KNX news
11 DE MARZO DE 2016
GWFcoder-System reads the absolute, mechanical meter measurement. Accurate and realiable (compelte reading precision via LEDs)!
The well-established GWFcoder®-system reads the absolute mechanical register value precisely and reliably and provides the data through standardized interfaces. The number wheels with three various long, asymmetrically arranged slots are being scanned through light pipes which are connected to five light emitting diodes (LED). Thus, the exact position of each number wheel can be detected and the encoded absolute register read can be transmitted. This functioning principle is patented by GWF. The GWFcoder®- interface provides an incomparably higher level of information compared to meters with pulse output.
GWF enhanced the reliable technology in its 2nd generation, so that 8 instead of 5 number wheels are being scanned and therefore a resolution of 1 liter is possible.
Parameter Setting
The available parameters allow you to define the following outputs: (type dependent)
- Meter value (m³)
- High-resolution meter value (l)
- Meter status
- Serial number and meter number
- Relative up counter Meter value / Reset
- Relative down counter Meter value / Reset / Zero
- Output 15min / 60min difference (m³)
- Due date billing Date / Set
- Output Flow rate
- Limit monitoring Flow rate 2 thresholds each
Storage of Consumption Data
The integrated KNX data logger stores the data at 15 minute intervals over a period of one year. The data can be read out directly via the NK-FW network coupler using a standard Internet browser. By using FTP, you can also download the stored data from the KNX/EIB module for further processing, for example with MS Excel or Flash / Silverlight. The application program offers 21 data points for further processing in the KNX/EIB bus. The individual data can be transmitted cyclically to the KNX bus.
GWF enhanced the reliable technology in its 2nd generation, so that 8 instead of 5 number wheels are being scanned and therefore a resolution of 1 liter is possible.
Parameter Setting
The available parameters allow you to define the following outputs: (type dependent)
- Meter value (m³)
- High-resolution meter value (l)
- Meter status
- Serial number and meter number
- Relative up counter Meter value / Reset
- Relative down counter Meter value / Reset / Zero
- Output 15min / 60min difference (m³)
- Due date billing Date / Set
- Output Flow rate
- Limit monitoring Flow rate 2 thresholds each
Storage of Consumption Data
The integrated KNX data logger stores the data at 15 minute intervals over a period of one year. The data can be read out directly via the NK-FW network coupler using a standard Internet browser. By using FTP, you can also download the stored data from the KNX/EIB module for further processing, for example with MS Excel or Flash / Silverlight. The application program offers 21 data points for further processing in the KNX/EIB bus. The individual data can be transmitted cyclically to the KNX bus.
05 DE AGOSTO DE 2010
NEW! IP-Pushbuttons from Lingg & Janke
These are not only innovative pushbuttons, but a new concept of equipping your KNX system with simple and low-priced control sensors.
Why are they unique?
• One Main module with BCU for up to 3 extension modules (up to 16 functions)
• Much less KNX components per line = reduction of system components
• Installation via pre-fabricated connection cables
• All their functions can be controlled via the facility web protocol on a pre-configured web page (in combination with a NK-FW gateway from Lingg & Janke)
What are the advantages?
• Very low-cost solution
• Very simple installation and configuration
• Very easy remote control via a standard web browser (Ex. with a PDA from the sofa)
These one-of-a-kind pushbuttons from Lingg & Janke come with a whole range of conventional mechanisms (HK05 Design from Kopp) which makes it a complete and all-round solution.
Check the the complete catalogue here.
Why are they unique?
• One Main module with BCU for up to 3 extension modules (up to 16 functions)
• Much less KNX components per line = reduction of system components
• Installation via pre-fabricated connection cables
• All their functions can be controlled via the facility web protocol on a pre-configured web page (in combination with a NK-FW gateway from Lingg & Janke)
What are the advantages?
• Very low-cost solution
• Very simple installation and configuration
• Very easy remote control via a standard web browser (Ex. with a PDA from the sofa)
These one-of-a-kind pushbuttons from Lingg & Janke come with a whole range of conventional mechanisms (HK05 Design from Kopp) which makes it a complete and all-round solution.
Check the the complete catalogue here.
23 DE JULIO DE 2010
New Current Transformer rated Energy Meter from Lingg & Janke
The long-awaited Current Transformer rated Energy Meter from Lingg & Janke has now been released! Up to now, with the existing energy meters from this manufacturer, you could only measure up to 85A, which is not enough for most industrial applications.
Using current transformers, you can measure any current and therefore open the range of Smart Metering projects to apply for.
This new counter has, just as the already existing counters, the Facility Web functionality implemented. This means that you can read out current and historical data of up one year via web browser (in combination with an NK-FW)
What makes this counter unique is that the transformation factor in each specific case will be fixed integrated in the counter. This makes configuration easier and less errors occur. Just keep in mind that you must indicate your transformation factor when submitting your order to Futurasmus KNX Group.
Of course, all the improvements in functionality that were implemented in the counter catalogue of Lingg & Janke not long ago, are also present here. In particular, it has the features of the 4 quadrant energy meter.
Using current transformers, you can measure any current and therefore open the range of Smart Metering projects to apply for.
This new counter has, just as the already existing counters, the Facility Web functionality implemented. This means that you can read out current and historical data of up one year via web browser (in combination with an NK-FW)
What makes this counter unique is that the transformation factor in each specific case will be fixed integrated in the counter. This makes configuration easier and less errors occur. Just keep in mind that you must indicate your transformation factor when submitting your order to Futurasmus KNX Group.
Of course, all the improvements in functionality that were implemented in the counter catalogue of Lingg & Janke not long ago, are also present here. In particular, it has the features of the 4 quadrant energy meter.
