If you still haven't created an account in our Web site and you are a professional from the sector, we invite you to do so. It is completely free and it will allow you to:
KNX presence detector with integrated KNX-BUS coupler Ceiling installation
DETECTORS
KNX presence detector with integrated KNX-BUS coupler Ceiling installation version Parameterization as of ETS 4 for integration in KNX systems The product database for import into the ETS database can be downloaded from the B.E.G. homepage.
KNX presence detector with integrated KNX-BUS coupler flush-mounted version
DETECTORS
KNX presence detector with integrated KNX-BUS interface Flush-mounted version Parameterization as of ETS 4 for integration in KNX systems The product database for import into the ETS database can be downloaded from the B.E.G. homepage.
KNX occupancy detector with integrated KNX bus connector 1x Light (for regulating or switching), 1x slave output, 3 separate HVAC blocs Intelligent semi-automatic mode, occupancy-independent regulating mode (photoelectric switch), full automatic mode Individual adaption of detection sensitivity for each PIR sensor Direction of movement can be identified Adaptation of dimming curve Mixed light measurement with internal and external light sensor Determination of the reflection factor, e.g. on a desk, with the optional BLE-IR adapter Burn-in function for fluorescent lamps selectable from 1h to 100h Various locking functions Status LEDs can be activated / deactivated Programming button can be operated via remote control Regulation / switching of three light groups via offset (external influence possible) Short presence, self-adjusting follow-up time, corridor function Soft-start Recall of light scenes HVAC mode (1 = comfort, 2 = standby, 3 = economy, 4 = antifreeze / heat protection) PIR sensors can be deactivated individually Detection area can be extended thanks to master-slave-mode Extensive optimization options for light measurement Measured light value is communicated to the bus IR remote control-capable via IR remote control (optional) PIN code Manual influence via external KNX push buttons possible Function control (heartbeat, cyclical sending) Forced switch-off Intelligent central-off function Premonition of switch-off Behavior on bus voltage definitive at choice Variable safety break after switching off the lights Settings ex ETS 4 for integration into KNX systems The product database for the ETS database can be downloaded from the B.E.G. homepage. Spring clamps blinds Typical applications: monitoring of large areas like underground garages, gyms, warehouses, loading ramps, halls
KNX occupancy detector designed for high-bay warehouses, with integrated KNX bus connector
External telescopic light sensor for a mounting height between 5 and 16m (mechanically adjustable) for measuring the light according to the application.
1x Light (for regulating or switching), 1x slave output, 3 separate HVAC-blocs
IR remote control-capable via 5 button remote control, programmable at choice (accessory)
Occupancy simulation
PIR sensors can be deactivated individually
Detection area can be extended thanks to master-slave-mode
Extensive optimization options for light measurement
Measured light value is communicated to the bus
IR remote control-capable via IR remote control (optionally)
PIN code
Manual influence via external KNX push buttons possible
Function control (heartbeat, cyclical sending)
Forced switch-off
Intelligent central-off function
Premonition of switch-off
Behaviour upon bus voltage return definable at choice
Variable safety pause after switching off the lights
Settings ex ETS 4 for integration in KNX systems
The product database for import into the ETS database can be downloaded from the B.E.G. homepage.
Adaption of dimming curve
Determination of the reflection factor, e.g. on a desk, with the optional BLE-IR-Adapter
Burn-in function for fluorescent lamps selectable from 1h till 100h
Soft-start
Blinds
There are markings for adjusting the detector
When used in high-bay warehouses, care should be taken that, in the cross-aisles of the warehouse, detectors are installed that can detect movement only in the desired aisle locations, by using blinds or other technical arrangements.
Application examples: monitoring of warehouses, high-bay storages where a large mounting height is given
KNX occupancy detector with integrated KNX bus connector
DETECTORS
KNX occupancy detector with integrated KNX bus connector 1x Light (for regulating or switching), 1x slave output, 3 separate HVAC-blocs HVAC mode (1=comfort, 2=stand-by, 3=economy, 4 = antifreeze/heat protection) Intelligent semi-automatic mode, occupancy-independent regulating mode (photoelectric switch), full automatic mode Individual adaption of the motion sensor sensitivity Detection area can be extended thanks to master-slave-mode Extensive optimization options for light measurement Measured light value is communicated to the bus Adaption of dimming curve Mixed light measurement with internal and external light sensor Determination of the reflection factor, e.g. on a desk, with the optional Infrared Luxmeter IR-LM IR remote control-capable via IR remote control (optionally) PIN code Burn-in function for fluorescent lamps selectable from 1h till 100h Various locking functions Status LEDs can be activated / deactivated Programming button (phys. address) can be operated via remote control Regulation/switching of three light groups via offset (external influence possible) Manual influence via external KNX push buttons possible Function control (heartbeat, cyclical sending) Short presence, self-adjusting follow-up time, corridor function Soft-start Forced switch-off Intelligent central-off function Recall of light scenes Premonition of switch-off Behaviour upon bus voltage return definable at choice Variable safety pause after switching off the lights ??Temperature- and noise sensor Settings ex ETS 4 for integration in KNX systems The product database for import into the ETS database can be downloaded from the B.E.G. homepage. Spring-clamps
KNX presence detector with integrated KNX-BUS interface Flush-mounted
DETECTORS
KNX presence detector with integrated KNX-BUS interface Flush-mounted version Presence simulation Parameterization from ETS 4 onwards for integration in KNX systems The product database for import into the ETS database can be downloaded from the B.E.G. homepage.
Pre-wired control unit for KNX occupancy detectors and other loads for being mounted in a false ceiling Gateway DALI/KNX for connecting up to 45 DALI lights GST18 plugs and sockets Pre-wiring allows for cost savings and prevents erroneous installations The integrated service switch allows for using (basic functions) the connected loads even without ETS All B.E.G. KNX motion and occupancy detectors can be combined with the KNX-RCT Already integrated are a DALI gateway, a roller shutter actuator and two push button interfaces
Automatic mode The parameterization to ETS 4 for the integration in KNX systems The product database for importing into the ETS system can be downloaded from the B.E.G. website. For the combination with cover frame (measurements of the inner cover 50 x 50 mm) in 5 different colors Examples of applications: monitoring of public facilities, toilets, corridors, libraries, meeting rooms Technical data Supply voltage: of the KNX bus Dimensions: (without bezel) 70 x 70 x 61 mm Rated current: 12 mA Detection angle: horizontal 180 ° Scope: max. 10 m cross max. 3 m frontal Cross coverage area: 157 m² / 1,1 m Assembly height
KNX occupancy detector with integrated KNX bus coupler, especially for installation in walls
DETECTORS
KNX occupancy detector with integrated KNX bus coupler, especially for installation in walls 1x Light (for regulating or switching), 1x slave output, 3 separate HVAC-blocs Intelligent semi-automatic mode, occupancy-independent regulating mode (photoelectric switch), full automatic mode Individual adaption of the motion sensor sensitivity Adaption of dimming curve Measuring of mixed light thanks to internal light sensor Determination of the reflection factor, e.g. on a desk, with the optional BLE-IR-Adapter Burn-in function for fluorescent lamps selectable from 1h till 100h Various locking functions Status LEDs can be activated / deactivated Programming button (phys. address) can be operated via remote control Regulation/switching of three light groups via offset (external influence possible) Short presence, self-adjusting follow-up time, corridor function Soft-start Recall of light scenes HVAC mode (1=comfort, 2=stand-by, 3=economy, 4 = antifreeze/heat protection) Detection area can be extended thanks to master-slave-mode Extensive optimization options for light measurement Measured light value is communicated to the bus IR remote control-capable via IR remote control (optionally) PIN code Manual influence via external KNX push buttons possible Function control (heartbeat, cyclical sending) Forced switch-off Intelligent central-off function Premonition of switch-off Behaviour upon bus voltage return definable at choice Variable safety pause after switching off the lights Settings ex ETS 4 for integration in KNX systems The product database for import into the ETS database can be downloaded from the B.E.G. homepage. For use with covering (interior cover dimensions 50x50mm) in 5 different colours In combination with centre plates usable with current frame systems of various manufacturers B.E.G. frames and centre plates for combination with other frame systems available Please order cover frame separately, available in various colours Application examples: monitoring of public lavatories, corridors, archive rooms, conference rooms
Futurasmus KNX Group is a highly specialized and internationally active KNX Wholesaler, being our forte the excellent technical support we provide. You can visit our online catalogue in this website and, if you are a professional, ask for a non binding offer for your KNX projects. Should you be interested in buying KNX components, you are welcome to read our General Sales Conditions and contact our technicians and commercial agents per telephone, e-mail or online help.
Since 2003 we have been a Certified Training Centre KNX++, which means that we are entitled to impart the KNX Basic Course as well as the KNX Advanced Course and KNX Tutor Course. We are manufacturer-independent and also offer other specialized and monographic KNX seminars. After teaching more than 1.500 KNX partners, our KNX Trainers have quite a large and positive expertise. Please, contact us for customized KNX training worldwide (groups of at least 8 people) at training@futurasmus-knxgroup.org
We use our own and third-party cookies, analyzing your browsing habits in out website, with the finality of ensuring the quality, security and improvement of the offered services through the same. In the case that the user does not explicitly state whether to accept the installation of cookies, but continues using our website, it will mean that he has consented expressly, informing him about the possibility to block or remove the installed cookies on his computer by configuring the appropriate settings of the browser. You can get more information on this subject reading our "Cookies Policy".