Order by:   Filter results: 
Web Code Reference Description Category Price
1260 2076-2 T 2-CHANNEL PUSHBUTTON INTERFACE INPUTS
The 2-channel and 4-channel pushbutton interfaces are equipped with 2/4 independent channels which - depending on parameterization - may be used as inputs or alternatively also as outputs (channels 1 or 2 only). The pushbutton interfaces can evaluate at their potentialfree inputs up to 2/4 pushbutton / switch states with a common reference potential and send the corresponding telegrams over the instabus EIB. The telegrams may be telegrams for switching or dimming, for blind/shutter control or for value transmitter applications (dimming value transmitter, light-scene extension, temperature or brightness value transmitters). Moreover, switch or pulse counters are available (2-channel type: 1 counter, 4-channel type: 2 counters). As an alternative, channels 1 and 2 can control up to 2 light-emitting diodes (LED) as independent outputs. To increase the output current (see technical data), these channels can also be connected in parallel with the same parametrization. The outputs are protected against short circuits, overload and wrong polarity. Technical data Supply instabus EIB : 21 - 32 V DC Power consumption : typically 150 mW Connection instabus EIB : instabus connecting terminal Inputs / Outputs dual type : 3-wire cable set quad type : 5-wire cable set length : 25 cm, can be prolonged to 5 m max. recommended cable : EIB bus line J-Y(St)Y 2x2x0.8mm Inputs dual type : up to 2 (depending on application) quad type : up to 4 (depending on application) Outputs for LEDs : max. 2 constant current : 0.8 mA per output Dimensions (W x H x D) : 44 x 29 x 16 mm Ambient temperature : -5 °C ... +45 °C Type of protection : IP 20 Safety class : III Technical specifications subject to change. ?? System information This unit is a product of the instabus-EIB-System and corresponds to the EIBA Guidelines. Detailed technical knowledge acquired in instabus training courses is a prerequisite for the understanding of the system. The functions of the device are software-dependent. Detailed information on the software and the functions implemented and the software itself are available from the manufacturer's product data bank. Planning, installation and commissionning of the device are effected with the help of EIBA-certified software. The updated product database and the technical description are available in the Internet under www.jung.de
1260
2076-2 T 2-CHANNEL PUSHBUTTON INTERFACE INPUTS
1261 2076-4 T CHANNEL PUSHBUTTON INTERFACE- 4-GANG INPUTS
The 2-channel and 4-channel pushbutton interfaces are equipped with 2/4 independent channels which - depending on parameterization - may be used as inputs or alternatively also as outputs (channels 1 or 2 only). The pushbutton interfaces can evaluate at their potentialfree inputs up to 2/4 pushbutton / switch states with a common reference potential and send the corresponding telegrams over the instabus EIB. The telegrams may be telegrams for switching or dimming, for blind/shutter control or for value transmitter applications (dimming value transmitter, light-scene extension, temperature or brightness value transmitters). Moreover, switch or pulse counters are available (2-channel type: 1 counter, 4-channel type: 2 counters). As an alternative, channels 1 and 2 can control up to 2 light-emitting diodes (LED) as independent outputs. To increase the output current (see technical data), these channels can also be connected in parallel with the same parametrization. The outputs are protected against short circuits, overload and wrong polarity. ?? Technical data Supply instabus EIB : 21 - 32 V DC Power consumption : typically 150 mW Connection instabus EIB : instabus connecting terminal Inputs / Outputs dual type : 3-wire cable set quad type : 5-wire cable set length : 25 cm, can be prolonged to 5 m max. recommended cable : EIB bus line J-Y(St)Y 2x2x0.8mm Inputs dual type : up to 2 (depending on application) quad type : up to 4 (depending on application) Outputs for LEDs : max. 2 constant current : 0.8 mA per output Dimensions (W x H x D) : 44 x 29 x 16 mm Ambient temperature : -5 °C ... +45 °C Type of protection : IP 20 Safety class : III Technical specifications subject to change. ?? System information This unit is a product of the instabus-EIB-System and corresponds to the EIBA Guidelines. Detailed technical knowledge acquired in instabus training courses is a prerequisite for the understanding of the system. The functions of the device are software-dependent. Detailed information on the software and the functions implemented and the software itself are available from the manufacturer's product data bank. Planning, installation and commissionning of the device are effected with the help of EIBA-certified software. The updated product database and the technical description are available in the Internet under www.jung.de
1261
2076-4 T CHANNEL PUSHBUTTON INTERFACE- 4-GANG INPUTS
2448 DAS 4110 AUßENSIRENE MIT BLITZLICHT SIN FAMILIA
Sabotageschutz gegen Aufschrauben und Wandabriss Anschluss an EAM 4000: a.) mind. 5-adrig, z.B. 3x2x0,8 JY-ST-Y b.) über Schaltaktor 6fach, z.B. Art.-Nr. 2136.6 REG für Blitz und Sirene (12 V DC aus Zentrale), Sabo-Kontakt über Binäreingang, z.B. Art.-Nr. 2126 REG bzw. Tasterschnittstelle, z.B. Art.-Nr. 2076-2 T bzw. 2076-4 T Technische Daten Betriebsspannung: 12 V DC (10,5 V – 13,5 V) Sirene Stromverbrauch: ca. 300 mA bei 12 V DC Lautstärke: ca. 112 dB (A) bei 1 m Abstand und 12 V DC Lautsprecher: Piezo (mit Tongenerator) Frequenz: 2 – 4 kHz Gehäusematerial: Polycarbonat Maße (B x H x T): 220 x 300 x 103 mm Schutzart: VdS-Umweltklasse IV; IP 34 Blitzlicht Stromverbrauch: ca. 200 mA bei 12 V DC Blitzfrequenz: ca. 35 Blitze/Minute bei 12 V DC Blitzenergie: ca. 0,8 Ws Lebensdauer: ca. 5.000.000 Blitze
2448
DAS 4110 AUßENSIRENE MIT BLITZLICHT SIN FAMILIA
2470 DAS 4300 U Flush-mounted key switch SIN FAMILIA
Flush-mounted key switch Front plate material: Lost-wax casted aluminium (profile cylinder lock is not included!)
2470
DAS 4300 U FLUSH-MOUNTED KEY SWITCH SIN FAMILIA
2471 28 Locking (profile cylinder) for key switch/push-button inserts (DIN 18 525) SIN FAMILIA
Locking (profile cylinder) for key switch/push-button inserts with individual keys
2471
28 LOCKING (PROFILE CYLINDER) FOR KEY SWITCH/PUSH-BUTTON INSERTS (DIN 18 525) SIN FAMILIA
2475 A 3180-1 A Automatik-Schalter 180° Komfort 1,10 m DETECTORS
KNX PIR automatic switch 180° 1.1 m, universal ETS-product family: Physical sensors Product type: Movement ranges AS 500/A 500/A plus. IVORY The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands or value transmission to devices such as binary outputs to switch groups of lights or dimming actuators. It can also be used to release a light scene in combination with a light scene push-button. It has three potentiometers for time, brightness and sensitivity adjustable from the front side. A slide switch (ON/AUTO/OFF) is also integrated. The automatic switch has two major modes. There is one for lighting purposes as already explained and one for monitoring purposes used for simple alarm detection or in connection with the Central Alarm Unit EAM 4000. By activating a specific object the device can be toggled between these modes.The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands or value transmission to devices such as binary outputs to switch groups of lights or dimming actuators. It can also be used to release a light scene in combination with a light scene push-button. It has three potentiometers for time, brightness and sensitivity adjustable from the front side. A slide switch (ON/AUTO/OFF) is also integrated. The automatic switch has two major modes. There is one for lighting purposes as already explained and one for monitoring purposes used for simple alarm detection or in connection with the Central Alarm Unit EAM 4000. By activating a specific object the device can be toggled between these modes.
2475
A 3180-1 A AUTOMATIK-SCHALTER 180° KOMFORT 1,10 M DETECTORS
2478 A 3280-1 A KNX PIR automatic switch 180° 2.2 m, universal DETECTORS
KNX PIR automatic switch 180° 2.2 m, universal ETS-product family: Physical sensors Product type: Movement ranges AS 500/A 500/A plu ivory The automatic switch has a detection angle of 180° and an area of 10 x 12 m. This angle can be restricted to 90° with a slip-on screen. The device has to be mounted in a height of 2.2 m. Additionally, the device has an integrated red LED used for testing mode or alarm indication when the cover was removed from the insert. It can also be programmed to release an alarm indication if somebody manipulated the cover. Software application: PIR universal
2478
A 3280-1 A KNX PIR AUTOMATIC SWITCH 180° 2.2 M, UNIVERSAL DETECTORS
2485 LS 3180-1 A KNX PIR automatic switch 180° 1,1 m, universal ivory DETECTORS
KNX PIR automatic switch 180° 1,1 m, universal ETS-product family: Physical sensors Product type: Movement ranges LS 990/LS plus/Stainless Steel/Aluminium/Anthracite/Gold/Chrome ivory The automatic switch has a detection angle of 180° and an area of 10 x 12 m. This angle can be restricted to 90° with a slip-on screen. The device has to be mounted in a height of 2.2 m. Additionally, the device has an integrated red LED used for testing mode or alarm indication when the cover was removed from the insert. It can also be programmed to release an alarm indication if somebody manipulated the cover. Software application: PIR universal A00802
2485
LS 3180-1 A KNX PIR AUTOMATIC SWITCH 180° 1,1 M, UNIVERSAL IVORY DETECTORS
2491 LS 3280-1 A KNX PIR automatic switch 180° 2.2 m, universal Ivory DETECTORS
KNX PIR automatic switch 180° 2.2 m, universal Ivory ETS-product family: Physical sensors Product type: Movement ranges LS 990/LS plus/Stainless Steel/Aluminium/Anthracite/Gold/Chrome The automatic switch has a detection angle of 180° and an area of 10 x 12 m. This angle can be restricted to 90° with a slip-on screen. The device has to be mounted in a height of 2.2 m. Additionally, the device has an integrated red LED used for testing mode or alarm indication when the cover was removed from the insert. It can also be programmed to release an alarm indication if somebody manipulated the cover. Software application: PIR universal A00802
2491
LS 3280-1 A KNX PIR AUTOMATIC SWITCH 180° 2.2 M, UNIVERSAL IVORY DETECTORS
2497 3180-1 A KNX PIR automatic switch 180° 2.2 m, universal Ivory DETECTORS
KNX PIR automatic switch 180° 2.2 m, universal Ivory ETS-product family: Physical sensors Product type: Movement ranges AS 500/A 500/A plus The automatic switch has a detection angle of 180° and an area of 10 x 12 m. This angle can be restricted to 90° with a slip-on screen. The device has to be mounted in a height of 2.2 m. Additionally, the device has an integrated red LED used for testing mode or alarm indication when the cover was removed from the insert. It can also be programmed to release an alarm indication if somebody manipulated the cover. Software application: PIR universal A00802
2497
3180-1 A KNX PIR AUTOMATIC SWITCH 180° 2.2 M, UNIVERSAL IVORY DETECTORS
2505 USV 640 MA KNX uninterrupted power supply 640 mA SYSTEM DEVICES
KNX uninterrupted power supply 640 mA ETS-product family: System component Product type: Power supply Series embodiment (SE)-device (8 units) The uninterrupted KNX power supply generates and monitors the system voltage. The integrated choke decouples the power supply and the bus-line. In order to buffer the KNX system-voltage during power failure, up to two 12 V lead-gel batteries can be connected. The batteries are charged by the power supply. The charging voltage is controlled temperature depending by the temperature sensor. In case of a power failure the uninterrupted power supply will be supplied by the batteries. The temperature sensor must be connected for a proper charging of the batteries. Via a floating change-over contact a failure of the uninterrupted power supply will be reported and stored. The following failures cause a switchover: power failure, battery failure, overvoltage, over load and short circuit. The max. charging time of the lead-gel battery amounts to 28 hours (1 x 12 Ah-battery) respectively 56 hours (2 x 12 Ah-batteries in parallel). 16 Technical data: Supplying Voltage: 230 V AC, +10/-15 %, 45 ... 65 Hz Power consumption: < 60 VA Power loss: < 10 W KNX Output Number 1 line with integrated choke Output voltage: 30 V DC, +1/-2 V, SELV Nominal current: 640 mA, permanent short circuit proof Permanent short-circuit current: < 1.5 A Mains failure bridgeover time: 200 ms (without connected battery) Battery type: lead-gel battery Number: max. 2 in parallel Rated voltage: recommended 1 Ah, 7 Ah, 12 Ah, 17 Ah Rated battery charge current: 650 mA, at battery capacity > 5 Ah 150 mA, at battery capacity < 5 Ah Temperature control: temperature-controlled charging voltage via temperature sensor Floating contact Rated voltage: 230 V AC resp. 12/24 V AC/DC Max. switching current: 6 A AC resp. 4 A DC Min. switching current: 100 mA (at U < 30 V AC/DC) Connections Change-over contact: 3 screw terminals each Battery and temperatur sensor: 2 screw terminals each Screw terminals: 0.2 ... 4 mm2 Operation temperature: -5°C ... +45°C
2505
USV 640 MA KNX UNINTERRUPTED POWER SUPPLY 640 MA SYSTEM DEVICES
2506 KSB 4 Cable-set Basis SIN FAMILIA
Cable-set Basis For the connection of the uninterrupted KNX power supply and the lead-gel battery the 4-wire cable-set (for one battery) respectively the 4-wire and the 2-wire set for two batteries must be used. The 4-wire cable-set has an integrated fuse and a temperature sensor, the 2-wire cable-set has only an integrated fuse. Technical data for: KSB 4 Cable: 4-wire cable 2-wire cable Diameter: 0,75 mm2 0,75 mm2 Length: 2 m 2 m Colours Battery connection: red (12 V battery) red (12 V battery) black (GND battery) black (GND battery) Temperature sensor: white (12 V temp. sensor) yellow (GND temp. sensor) Connection Battery: for the connection to the for the connection to the uninterrupted power supply: uninterrupted power supply: wire end sleeve wire end sleeve for connection to the battery: for connection to the battery: cable lug cable lug Temperature sensor: wire end sleeve Fuse: 5 x 20 mm, T6,3 H 250 V 5 x 20 mm, T6,3 H 250 V
2506
KSB 4 CABLE-SET BASIS SIN FAMILIA
2510 2070 U KNX bus coupling unit with supporting frame SYSTEM DEVICES
KNX bus coupling unit with supporting frame for flush mounting ETS-product family: System components Product type: Bus coupling unit suitable for wall boxes with Ø 60 mm The bus coupling unit (BCU) enables application modules (AM) to be connected to the KNX. The AM could be a push-button, sensor or display fixed with the BCU. The telegrams received via the KNX are processed by the BCU and passed on to the AM. In the opposite direction, signals coming from the AM are converted into telegrams and transmitted to the bus. With the help of the programming push-button and the programming LED the physical address is saved in the BCU. Technical data: Supply voltage: 24 V DC (+6 V / –4 V) Power consumption: max. 100 mW, max. 150 mW with application module Connection: KNX connection block Notes to the Al Output voltage: 5 V DC + 0,4 V; 24 V DC (+6 V / –4 V) Output power: max. 50 mW Protection: IP 20 Operation temperature: –5°C ... +45°C Storage temperature: –40°C ... +55°C Mounting: fitted in wall box 60 mm Dimensions: Depth of recess: 32 mm
2510
2070 U KNX BUS COUPLING UNIT WITH SUPPORTING FRAME SYSTEM DEVICES
2532 A 3180 Automatic switch 180° standard 1.10 m, AS 500, A 500, A plus white , empotrble DETECTORS
KNX PIR automatic switch 180° 1.1 m, standard ETS-product family: Physical sensors Product type: Movement ranges AS 500/A 500/A plus The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180° and an area of 10 x 12 m.This angle can be restricted to 90° with a slip-on screen. The device has to be mounted at a height of 1.1 m.
2532
A 3180 AUTOMATIC SWITCH 180° STANDARD 1.10 M, AS 500, A 500, A PLUS WHITE , EMPOTRBLE DETECTORS
2535 A 3280 KNX PIR automatic switch 180 2.2 m, standard, Standard AS 500, A 500, A plus, white,for bcu empotrable DETECTORS
KNX PIR automatic switch 180 2.2 m, standard In connection with the KNX/EIB system, the functionality of this device depends on software. Detailed information on loadable software and attainable functionality as well as the software itself can be obtained from the manufacturers product database. ETS-product family: Physical sensors Product type: Movement ranges AS 500/A 500/A plus The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180 and an area of 12 x 12 m. This angle can be restricted to 90 with a slip-on screen. The device has to be mounted at a height of 2.2 m. Software applications: PIR single unit A00101 Vers. 1 PIR master A00201 Vers. 1 PIR extension A00301 Vers. 1 PIR automatic switch - standard Ref.-No. ..3x80..
2535
A 3280 KNX PIR AUTOMATIC SWITCH 180 2.2 M, STANDARD, STANDARD AS 500, A 500, A PLUS, WHITE,FOR BCU EMPOTRABLE DETECTORS
2543 2130 USB KNX USB DATA-INTERFACE 2130 USB REG SYSTEM DEVICES
KNX USB data-interface 2130 USB REG ETS-product family: Communication The USB data interface enables the coupling of a PC for the addressing, programming and diagnoses of KNX components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the KNX if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future standards. For 2130 USB and 2130 USB REG Note: The USB data interface is supported by ETS 3 software from version a upwards and by the PC operating systems Windows 98, 98 SE, ME, 2000 and XP. Connection: The connection to the KNX is carried out with the aid of the bus connecting terminal. The USB connection is carried out with a certified USB cable (1 x B plug required) with a max. length of 5 m. 26 4 Technical data: Power supply: via USB port of the PC Connection KNX: KNX connecting terminal USB port: USB socket, type B Transmission protocol: compatible with USB 1.1/2.0 Length of USB cable: max. 5 m Ambient temperature: 5C ... +45C Storage temperature: 25C ... +70C Protection: IP 20 Protection class: II
2543
2130 USB KNX USB DATA-INTERFACE 2130 USB REG SYSTEM DEVICES
2605 3180 Automatic switch 180° standard 1.10 m white DETECTORS
KNX PIR automatic switch 180° 1.1 m, standard ETS-product family: Physical sensors Product type: Movement The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180° and an area of 10 x 12 m.This angle can be restricted to 90° with a slip-on screen. The device has to be mounted at a height of 1.1 m. Software applications: PIR single unit A00101 Vers. 1 PIR master A00201 Vers. 1 PIR extension A00301 Vers. 1
2605
3180 AUTOMATIC SWITCH 180° STANDARD 1.10 M WHITE DETECTORS
2612 3280 KNX PIR AUTOMATIC SWITCH 180° 2,20 m, standars desing cd 500 cd plus, white DETECTORS
KNX PIR automatic switch 180° 2.20 m, standard ETS-product family: Physical sensors Product type: Movement The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180° and an area of 10 x 12 m.This angle can be restricted to 90° with a slip-on screen. The device has to be mounted at a height of 1.1 m. Software applications: PIR single unit A00101 Vers. 1 PIR master A00201 Vers. 1 PIR extension A00301 Vers. 1
2612
3280 KNX PIR AUTOMATIC SWITCH 180° 2,20 M, STANDARS DESING CD 500 CD PLUS, WHITE DETECTORS
2625 3280-1 A Automatik-Schalter 180° Komfort 2,20 m universal, With procteccion disassembly, desing cd 500 cd plus, white DETECTORS
KNX PIR automatic switch 180° 2.2 m, universal ETS-product family: Physical sensors Product type: Movement The automatic switch has a detection angle of 180° and an area of 10 x 12 m. This angle can be restricted to 90° with a slip-on screen. The device has to be mounted in a height of 2.2 m. Additionally, the device has an integrated red LED used for testing mode or alarm indication when the cover was removed from the insert. It can also be programmed to release an alarm indication if somebody manipulated the cover. Software application: PIR universal A00802
2625
3280-1 A AUTOMATIK-SCHALTER 180° KOMFORT 2,20 M UNIVERSAL, WITH PROCTECCION DISASSEMBLY, DESING CD 500 CD PLUS, WHITE DETECTORS
2709 LS 3180 Automatic switch 180° standard 1.10 m. standard, Of wall., desing, LS 990, LS plus, white DETECTORS
KNX PIR automatic switch 180° 1.1 m, standard ETS-product family: Physical sensors Product type: Movement The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180° and an area of 10 x 12 m.This angle can be restricted to 90° with a slip-on screen. The device has to be mounted at a height of 1.1 m. Software applications: PIR single unit A00101 Vers. 1 PIR master A00201 Vers. 1 PIR extension A00301 Vers. 1
2709
LS 3180 AUTOMATIC SWITCH 180° STANDARD 1.10 M. STANDARD, OF WALL., DESING, LS 990, LS PLUS, WHITE DETECTORS
2715 LS 3280 KNX PIR AUTOMATIC SWITCH 180° 2.2 M, STANDARD, OF WALL , DESING LS 990, LS PLUS, WHITE DETECTORS
KNX PIR automatic switch 180° 2.2 m, standard ETS-product family: Physical sensors Product type: Movement ranges LS 990/LS plus/Stainless Steel/Aluminium/Anthracite/Gold/Chrome The KNX automatic switch is plugged onto a flush mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180° and an area of 12 x 12 m. This angle can be restricted to 90° with a slip-on screen. The device has to be mounted at a height of 2.2 m. Software applications: PIR single unit A00101 Vers. 1 PIR master A00201 Vers. 1 PIR extension A00301 Vers. 1 Technical data: Supply Voltage: 24 V DC (+6 V / -4 V) via BCU Power consumption: max. 110 mW Connection: 2 x 5-pole pin bar Protection: IP 20 Insulation voltage: referring to V VDE 0829 part 230 Behaviour at Bus voltage drop: no telegrams are sended Bus voltage return: object values = 0, out of function for approx. 80 sec. Operation temperature: -5°C ... +45°C Storage temperature: -25°C ... +75°C Mounting: plugged onto a flush mounted BCU
2715
LS 3280 KNX PIR AUTOMATIC SWITCH 180° 2.2 M, STANDARD, OF WALL , DESING LS 990, LS PLUS, WHITE DETECTORS
2772 2002 REG Power supply 640 mA SYSTEM DEVICES
Power Supply 320 mA Power Supply 640 mA ?? General system information This device is a product of the instabus-EIB system and complies with the EIBA Guidelines. Detailed technical knowledge acquired in instabus training courses is a prerequisite to proper understanding. ?? Function The 320 mA and 640 mA power supplies generate and monitor the instabus EIB system voltage of 30V DC (SELV). 320 mA power supply: Supply of a bus line with max. 32 instabus users via the BUS output without additional instabus EIB choke. 640 mA power supply: Supply of max. 64 instabus users arbitrarily distributed over 2 bus lines via the outputs BUS 1 and BUS 2 without additional instabus EIB choke. The 30V DC output in both devices is not equipped with a choke and permits supplying another line (e.g. main line) via a separately installed instabus EIB choke. This output can alternatively be used for the supply of further functional devices (e.g. auxiliary voltage for binary inputs). Important: The distribution of loads over the outputs is optional, provided that the total rated current is not exceeded. Safety warnings Attention: Electrical equipment must be installed and fitted only by qualified electricians and in observance of the applicable accident prevention regulations. To prevent electric shocks, disconnect the power supply before working on the device (by cutting out the circuit breaker). Any non-observance of the fitting instructions may cause fire or other hazards. ?? Installation The instabus EIB power supply unit must be installed exclusively on a 35 mm DIN rail in distribution boxes or in switch cabinets. Ensure sufficient ventilation to prevent the admissible temperature range of the device from being exceeded. ?? Connection The supply mains is connected to terminals L, N and in accordance with the schematic. The choke-equipped instabus output lines are connected to the terminals marked ‘BUS’ by means of an instabus connector. Connection to the voltage output without choke is made by means of an instabus connector to the terminal marked ’30V DC’. The power supplies can be connected in parallel in accordance with the EIB guideline, if the line length between two power supplies is at least 200 m on the bus side.
2772
2002 REG POWER SUPPLY 640 MA SYSTEM DEVICES
2773 2005 REG KNX power supply 320 mA SYSTEM DEVICES
KNX power supply 320 mA 2005 REG ETS-product family: System components Product type: Power supply Series embodiment (SE)-device (4 units) The power supply 320 mA produces and controls the system power for the KNX. The devices can be connected to a bus line via the terminal BUS, without an additional choke. Furthermore, the power supply offers a 30 V DC output to supply a further bus line (i.e. main line). For this an additional choke is required. Alternatively, that output can be used as a power supply for any further low voltage equipment. The connection of the bus by a bus terminal on the device does not require any data rail. The distribution of the load (KNX devices) is flexible on both outputs, but the rated current of 320 mA is the total limit. There is one reset switch on the device to short-circuit the bus line. The operation time for a reset should be at least 20 sec. Four LEDs are indicating the different operation status: LED-indication: 1st red LED: short-circuit or overload green LED: normal operation yellow LED: over voltage, when bus voltage > 31 V DC 2nd red LED: reset 1 for bus line 1 KNX power supply 320 mA 2005 REG ETS-product family: System components Product type: Power supply Series embodiment (SE)-device (4 units) The power supply 320 mA produces and controls the system power for the KNX. The devices can be connected to a bus line via the terminal BUS, without an additional choke. Furthermore, the power supply offers a 30 V DC output to supply a further bus line (i.e. main line). For this an additional choke is required. Alternatively, that output can be used as a power supply for any further low voltage equipment. The connection of the bus by a bus terminal on the device does not require any data rail. The distribution of the load (KNX devices) is flexible on both outputs, but the rated current of 320 mA is the total limit. There is one reset switch on the device to short-circuit the bus line. The operation time for a reset should be at least 20 sec. Four LEDs are indicating the different operation status: LED-indication: 1st red LED: short-circuit or overload green LED: normal operation yellow LED: over voltage, when bus voltage > 31 V DC 2nd red LED: reset 1 for bus line 1 Technical data: Input supplying Voltage: 161 V 264 V AC, 50-60 Hz Operation with 2 lines of 110 V mains possible ! 176 V 270 V DC (for emergency power supply) Power consumption: < 5 W under normal operation Connection: screw terminals 0.2 4 qmm single wire 2 x 0.2 2.5 qmm single wire Output Number 2 Bus terminal BUS 1 Rated voltage: 28 V 31 V DC, SELV Connection: KNX connection block Bus terminal 30 V DC Rated voltage: 28 V 31 V DC, SELV Connection: KNX connection block Rated current: max. 320 mA (BUS + 30 V DC) short-circuit protection Protection: IP 20 Operation temp.: 5C ... +45C Storage temp.: 25C ... +55C / +70C Mounting: on DIN rail 35 x 7.5
2773
2005 REG KNX POWER SUPPLY 320 MA SYSTEM DEVICES
2775 2130 USB REG USB-Datenschnittstelle REG SYSTEM DEVICES
KNX USB data-interface 2130 USB REG ETS-product family: Communication for DIN rail mounting Series embodiment (SE)-device (2 unit) The USB data interface enables the coupling of a PC for the addressing, programming and diagnoses of KNX components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the KNX if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future standards. For 2130 USB and 2130 USB REG Note: The USB data interface is supported by ETS 3 software from version a upwards and by the PC operating systems Windows 98, 98 SE, ME, 2000 and XP. Connection: The connection to the KNX is carried out with the aid of the bus connecting terminal. The USB connection is carried out with a certified USB cable (1 x B plug required) with a max. length of 5 m. Technical data: Power supply: via USB port of the PC Connection KNX: KNX connecting terminal USB port: USB socket, type B Transmission protocol: compatible with USB 1.1/2.0 Length of USB cable: max. 5 m Ambient temperature: 5C ... +45C Storage temperature: 25C ... +70C Protection: IP 20 Protection class: II
2775
2130 USB REG USB-DATENSCHNITTSTELLE REG SYSTEM DEVICES
2793 2193 REG Control unit 3-gang REG ACTUATORS - OUTPUTS
KNX control unit, 3-gang 2193 REG ETS-product family: Illumination Product type: Dimmer Series embodiment (SE)-device (4 units) The control unit receives telegrams for switching or dimming fluorescent lamps operated with an electronic ballast (ELB dynamic-type). The dimming signal is controlled by a 1-10 V interface input. Switching is effected by a relay contact that switches the ballasts voltage supply ON and OFF. This contact can also be actuated manually without any effect on the bus by 3 hardware slide switches. Technical data Supply Voltage: 24 V DC (+6 V / 4 V) Power consumption: max. 240 mW Connection: KNX connection block Input Number: 3 Signal voltage: 1 10 V Signal current: max. 100 mA per channel dependent on type of ballast (e.g. 1 INSTA ELB: 0.8 mA, Siemens ELB: 1 mA) Performance: Power MOS-FET, trailing edge or leading edge Rated voltage: 230 V AC 10 %, 50/60 Hz Rated current: 2 x 1.1 A Connection: clamp bar Length of wire: max. 500 m at 0.5 mm2 Output Number: 3 Performance: 3 make-contact, floating point Rated voltage: 230 V AC 10 %, 50 Hz Rated current: 16 A (ohmic load), dependent on the fluorescent lamps Capacity: 2500 W ohmic load 1100 W / 140 F capacitive load dependent on the ballast due to different inrush currents: i.e. max. 15 INSTA ELB TC 1 10 V (single tube) max. 12 INSTA ELB TC 1 10 V (double tube) Connection: clamp bar Protection: IP 20
2793
2193 REG CONTROL UNIT 3-GANG REG ACTUATORS - OUTPUTS
2808 WS 10 W WIND SENSOR WS 10 W (NO KNX DEVICE) SENSORS
Wind sensor WS 10 W (No KNX device) The wind sensor converts the wind speed into electrical signals. These signals are generated by a Reed contact which closes under the influence of magnets. The generated impulses are transformed into an output voltage proportional to the wind speed. A PTC-heating element takes care for a trouble free winter operation (only in combination with heating transformer WSSV 10). Technical data Range: 0,7 ... 40 m/s Electrical output: 0 ... 10 V at 40 m/s Supply voltage: 18 ... 32 V DC Current consumption: 6 ... 12 mA Contact type: Reed contact Heating: PTC-element (800 C) Operating voltage heating: 24 V AC/DC Lead wire: 3 m (LIYY 6 x 0.25 mm2)
2808
WS 10 W WIND SENSOR WS 10 W (NO KNX DEVICE) SENSORS
2809 WS 10 R RAIN SENSOR WS 10 R SENSORS
Rain sensor WS 10 R (No KNX device) The rain sensor is used for the measuring and evaluation of the rainfall. With a meander shaped sensor the conductance of the rain water is evaluated. A micro processor controls the heating (only in combination with heating transformer WSSV 10) and offers an output signal of 0 V or 10 V. Technical data Range of the electrical output: 0 V dry / 10 V rain (min. 1 kO load) Lead wire: 3 m (LIYY 5 x 0.25 mm2) Plasting housing with sealed electronics Connections: brown operating volt. + 24 V white correspond. ground green output 0 V / 10 V yellow heating 24 V grey heating 24 V
2809
WS 10 R RAIN SENSOR WS 10 R SENSORS
2812 WS 10 D DAWN SENSOR WS 10 D SENSORS
Dawn sensor WS 10 D (No KNX device) The dawn sensor is used for the measuring and evaluation of the brightness (dawn/dusk). The brightness measured by a photodiode is transmitted to an analog output signal of 0 V 10 V by the electronics. Technical data Range: 0 ... 255 Lux, linear Electrical output: 0 V ... 10 V, short-circuit / proof Protection: IP 65 Plasting housing with PG7 thread + screw and pressure respectively moisture compensation (recommended cable 3 x 0,25 mm2)
2812
WS 10 D DAWN SENSOR WS 10 D SENSORS
2815 2131.16 UP 1-gang switch actuator 16A FM INPUTS
KNX switch actuator, flush mounted 1-gang 2131.16 UP 2-gang 2132.6 UP ETS-product family: Output Product type: 1(2)-gang binary output The switching actuator receives telegrams from sensors via the KNX and switches an electrical load with its relay-output. The device is equipped with two extension inputs which - depending on parameterization - can act directly on the switching output (local control / only input 1, input 2 without function) or alternatively as binary inputs on the KNX. The connected potential-free switch or push-button contacts are sensed against a common reference potential at the switching actuator. As a binary input, the device can transmit telegrams for switching or dimming, for shutter/blind control or for value transmitter applications (dimming value transmitter, light-scene extension). Connecting 230 V signals or other external voltages to the extension inputs is not permitted. The switching actuator is supplied from the KNX and needs no additional external power supply. Technical data KNX supply Cable type: YY 6 x 6.0 mm; red: bus (+) / black: bus (-) Voltage: 21 - 32 V DC SELV Power consumption: typically 150 mW Connection: approx. 33 cm ready-made; connecting terminal (0.6 - 0.8 mm) Input Number: 2 (depending on parameterization either as extension inputs for push-button local control of the actuator or as independent binary inputs acting on the bus) Cable type: YY 6 x 0.6 mm green: extension input 1 white: reference potential (com) yellow: extension input 2 brown: reference potential (com) Cable length: approx. 33 cm ready-made, extendible to 5 m max. Scanning voltage: approx. - 19 V DC referred to "com"; continuous signal Loop resistance: max. 2 kOhm for safe "1" signal detection (rising edge) Output, for 2131.16 UP Number: 1 Cable type: 2 x H05 V-K 2.5 mm2 with ferrules Cable length: approx. 20 cm ready-made Switch type: make-contact, potential-free (µ-contact) bistable Switching voltage: 230 V AC; 50/60 Hz Max. switching current: 16 A Max inrush current: 400 A, 20 ms Switching capacity: Incandescent lamps 2.500 W (at 100.000 switching operations) HV halogen lamps 2.200 W (at 100.000 switching operations) LV halogen lamps inductive transformers 1.000 VA electronic transformers 1.000 W capacitive loads 230 V AC, 10 A switching current, max. 105 µF Output, for 2132.6 UP Number: 2 (with common phase connection "L") Cable type: 3 x H05 V-K 2.5 mm2 with ferrules Cable length: approx. 20 cm ready-made Switch type: make-contact, potential-free (µ-contact) bistable Switching voltage: 230 V AC; 50/60 Hz Max. switching current: 6 A for each output Max inrush current: 120 A, 20 ms Switching capacity: Incandescent lamps 1.200 W (at 25.000 switching operations) HV halogen lamps 1.200 W (at 25.000 switching operations) LV halogen lamps inductive transformers 500 VA electronic transformers 500 W capacitive loads 230 V AC, 6 A switching current, max. 14 µF Protection: IP 20 Safety class: III Mark of approval: KNX Ambient temperature: -5°C ... +45°C Storage/transport temperature: -25°C ... +70°C (storage above +45°C results in shorter lifetime) Mounting position: any Minimum spacings: none Fastening: e.g. placing into deep flush-mounting box (Ø 60 mm x 60 mm)
2815
2131.16 UP 1-GANG SWITCH ACTUATOR 16A FM INPUTS
2829 2050 RT SW Supply terminals SYSTEM DEVICES
KNX Bus connection block 2 poles, 4 connection points 2050 RT SW ETS-product family: System accessories Product type: Connection block Plug-in connections (screwless) 2 x 4 0.6 ... 0.8 mm single core
2829
2050 RT SW SUPPLY TERMINALS SYSTEM DEVICES
2960 LS 990 SW 1-GANG ROCKER BLACK SIN FAMILIA
LS 990 1-gang rocker for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: BLACK Manufacturer: JUNG Ref.-no.: LS 990 LG
2960
LS 990 SW 1-GANG ROCKER BLACK SIN FAMILIA
2966 LS 990 P SW WIPPE FÜR TASTER BA 1FACH SIN FAMILIA
KNX Taster BA Wippe mit Symbolen für Taster BA 1fach Mittenstellung Art.-Nr.: 2071.02 LED Farbe: schawrz Fabrikat : Jung Art.-Nr.: LS 990 P LG
2966
LS 990 P SW WIPPE FÜR TASTER BA 1FACH SIN FAMILIA
2972 LS 990 NA SW WIPPE MIT SCHRIFTFELD SIN FAMILIA
LS 990 Wippe mit Schriftfeld 7 x 57 mm für Schalter Art.-Nrn.: 506 U, 507 U, 502 U, 503 U für Tastschalter Art.-Nrn.: 506 TU, 507 TU, 502 TU für Taster Art.-Nrn.: 531 U, 533 U, 533-2 U für Taster BA 1fach Mittenstellung Art.-Nr.: 2071.02 LED Tasterstellung Art.-Nr.: 2071.01 LED Beschriftungsbogen, weiß 1 Bogen = 34 Nutzen 7 x 57 mm: Art.-Nr. BB 3 Mit Dichtungsflansch Art.-Nr.: 551 WU und programmspezifischen "IP 44-Rahmen" ist der Schutzgrad IP 44 gewährleistet. Farbe: lichtgrau (ähnlich RAL 7035) Fabrikat : Jung Art.-Nr.: LS 990 NA LG
2972
LS 990 NA SW WIPPE MIT SCHRIFTFELD SIN FAMILIA
2978 LS 990 KO5 SW WIPPE FÜR KONTROLLSCHALTE SIN FAMILIA
KNX Taster BA Wippe mit Lichtleiter für Kontrollschalter Art.-Nrn.: 506 KOU, 502 KOU, 503 KOU für Tast-Kontrollschalter Art.-Nrn.: 506 KOTU, 502 KOTU für beleuchtbare Taster Art.-Nrn.: 531 U, 533 U, 533-2 U, 534 U für Taster BA 1fach Mittenstellung Art.-Nr.: 2071.02 LED Tasterstellung Art.-Nr.: 2071.01 LED Mit Dichtungsflansch Art.-Nr.: 551 WU und programmspezifischen "IP 44-Rahmen" ist der Schutzgrad IP 44 gewährleistet. Farbe: SCHWARZ
2978
LS 990 KO5 SW WIPPE FÜR KONTROLLSCHALTE SIN FAMILIA
3118 LS 995 SW 2-GANG ROCKER SIN FAMILIA
LS 990 Wippe für Serienschalter Art.-Nr.: 505 U für Tast-Serienschalter Art.-Nrn.: 505 TU, 505 TU-91 für Doppel-Wechselschalter Art.-Nr.: 509 U für Tast-Doppelwechselschalter Art.-Nr.: 509 TU für Doppel-Taster Art.-Nrn.: 535 U, 539 U für Multi-Switch Art.-Nr.: 532-4 U (nicht Metallausführungen) für Taster BA 2fach Mittenstellung Art.-Nr.: 2072.02 LED Tasterstellung Art.-Nr.: 2072.01 LED Mit Dichtungsflansch Art.-Nr.: 551 WU und programmspezifischen "IP 44-Rahmen" ist der Schutzgrad IP 44 gewährleistet. Farbe: SCHWARZ
3118
LS 995 SW 2-GANG ROCKER SIN FAMILIA
3124 LS 995 MP SW 2-GANG ROCKER WITH SYMBOLSFOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Taster BA Wippe mit Symbolen für Taster BA 2fach Mittenstellung Art.-Nr.: 2072.02 LED Farbe: SCHWARZ Fabrikat : Jung Art.-Nr.: LS 995 MP LG
3124
LS 995 MP SW 2-GANG ROCKER WITH SYMBOLSFOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
4633 2132.6 UP Flush-mounted switch actuator, 2-gang with satellite input, 6A INPUTS
Flush mounted switch actuator 2-gang, 6 A with 2-gang universal binary input ETS product family: Output The switching actuator receives telegrams from sensors via the KNX and switches an electrical load with its relay-output. The device is equipped with two extension inputs which - depending on parameterization - can act directly on the switching output (local control / only input 1, input 2 without function) or alternatively as binary inputs on the KNX. The connected potential-free switch or push-button contacts are sensed against a common reference potential at the switching actuator. As a binary input, the device can transmit telegrams for switching or dimming, for shutter/blind control or for value transmitter applications (dimming value transmitter, light-scene extension). Connecting 230 V signals or other external voltages to the extension inputs is not permitted. The switching actuator is supplied from the KNX and needs no additional external power supply.
4633
2132.6 UP FLUSH-MOUNTED SWITCH ACTUATOR, 2-GANG WITH SATELLITE INPUT, 6A INPUTS
4724 2204.01 REGAM Analog actuator module, 4-gang ACTUATORS - OUTPUTS
KNX Devices Analog actuator module, 4-gang Rail mounting device, 4 rail units Extension module ¦ The analog output extension module exceeds a KNX Analog output, 2204.01 REGA by four additional sensor outputs. ¦ The analog output extension module offers four analog outputs which can be software parameterised for one of the following ranges. ¦ Outputs not used can be deactivated. Voltage signals: 0 ... 1 V DC 0 ... 10 V DC Current signals: 0 ... 20 mA DC 4 ... 20 mA DC Power supply Supply voltage: AC 24 V ~ ± 10 % Current consumption: max. 120 mA Current consumption at system connector: 6 mA Ambient temperature: – 5 °C ... + 45 °C Storage/transport temperature: – 25 °C ... + 70 °C Humidity Ambient/storage/transport: max. 93% r. F., no condensation Protection level: IP 20 acc. DIN EN 60 529 Mounting width: 4 TE / 72 mm Weight: approx. 155 g Terminals Outputs, power supply: screw terminals single wire: 0.5 ... 4 mm2 stranded without ferrule: 0.5 ... 4 mm2 stranded with ferrule: 0.5 ... 2.5 mm2 Connection KNX device: KNX bus connection block Analog outputs Number: 4 Ranges: 0 ... 1 V DC, 0 ... 10 V DC, 0 ... 20 mA DC, 4 ... 20 mA, DC Voltage signal load: = 1 kW Current signal load: = 500 W Manufacturer: JUNG Ref.-no.: 2204.01 REGAM
4724
2204.01 REGAM ANALOG ACTUATOR MODULE, 4-GANG ACTUATORS - OUTPUTS
4738 3210 UP KNX DIMMING ACTUATOR, FLUSH MOUNTED INPUTS
KNX dimming actuator, flush mounted 1-gang 3210 UP ETS-product family: Illumination Product type: Dimmer The universal dimming actuator receives telegrams for switching or dimming purposes. It can work with the principle of trailing or leading edge control. That means either low voltage halogen lamps with TRONIC transformer or conventional (inductive) transformer can be controlled. The device is equipped with two extension inputs which depending on parameterization can act directly on the switching output (local control with input 1) or alternatively as binary inputs on the KNX. The connected potential-free switch or push-button contacts are sensed against a common reference potential at the dimming actuator. As a binary input, the device can transmit telegrams for switching or dimming, for shutter/ blind control or for value transmitter applications (dimming value transmitter, light-scene extension). Connecting 230 V signals or other external voltages to the extension inputs is not permitted. The dimming actuator is supplied from the KNX and needs therefore no additional external power supply. Technical data KNX supply Cable type: YY 6 x 6.0 mm; red: bus (+) / black: bus () Voltage: 21 32 V DC SELV Power consumption: typically 150 mW Connection: approx. 33 cm ready-made; connecting terminal (0.6 0.8 mm) Input Number: 2 (depending on parameterization either as extension inputs for push-button local control of the actuator or as independent binary inputs acting on the bus) Cable type: YY 6 x 0.6 mm green: extension input 1 white: reference potential (com) yellow: extension input 2 brown: reference potential (com) Cable length: approx. 33 cm ready-made, extendible to 5 m max. Scanning voltage: approx. 19 V DC referred to com; continuous signal Loop resistance: max. 2 kOhm for safe 1 signal detection (rising edge)
4738
3210 UP KNX DIMMING ACTUATOR, FLUSH MOUNTED INPUTS
5223 2504 REGHE Blinds actuator, 4-gang AC 230 V, 2-gang DC 12-48 V ACTUATORS - OUTPUTS
Blinds actuator, 4-gang AC 230 V, 2-gang DC 12-48 V Rail mounting device, 4 units with manual electronic operation and LED status indication For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Shutter Technical data Outputs: 4 channels AC 230 V, 2 channels DC 12...48 V Contact type: make contact, potential-free Power supply mains: AC 110 V (-10 %) ... 240 V (+10 %) 50/60 Hz Wiring: screw terminals single wire: 0.5 ... 4 mm2 stranded without ferrule: 0.5 ... 4 mm2 stranded with ferrule: 0.5 ... 2.5 mm2 Breaking capacity AC1: 6 A (230 V) Switching current DC 12/24 V: 6 A Switching current DC 48 V: 3 A Max. blind/shutter running time: 20 min An ON-time must be followed by an OFF-time of at least the same length. Ambient temperature: -5 °C ... +45 °C Storing temperature: -25 °C ... +70 °C Product type: Shutter
5223
2504 REGHE BLINDS ACTUATOR, 4-GANG AC 230 V, 2-GANG DC 12-48 V ACTUATORS - OUTPUTS
5224 2316.16 REGHE KNX SWITCH/BLINDS ACTUATOR ACTUATORS - OUTPUTS
KNX Switch/blinds actuator Switch 8-gang, Blinds 4-gang The switching actuator receives telegrams from sensors or other controls via the KNX and switches electrical loads by its independent contacts. The relay outputs can be adjusted alternatively to switching or blinds operation by the software. Also a mixed switching/blinds operation is possible. Within the blinds operation, the actuator can operate blinds, shutters, awnings, ventilation flaps, curtains or other drives for 230V AC. In the switching mode it operates e.g. lighting applications or also low voltages. Each output has a line voltage supplied mono stabile relay. This way also preferred positions can be adjusted even at bus voltage drop. By means of the 4 push-buttons on top of the device, the relays can be operated by hand in parallel to the KNX without bus voltage or programming. Within the blinds operation mode, the functional scope includes separate adjustable driving times, advanced acknowledge functions, assignments to up to 5 safety functions, an extensive sun protection as well as scenarios and forced position functions. Also a central control of all blinds outputs is possible. Within the switching mode, the functional scope for each output channel includes extensive time functions, logics, scenarios or inhibit-functions and advanced acknowledge functions. Also the central switching of all outputs is possible. For projecting and commissioning the use of ETS 3.0d is recommended. Only with this ETS version or later versions the full functionality will be available (vd4-file). For ETS2 and older versions of ETS3 separate databases are available (vd2-file). Technical data KNX Supply Voltage: 21 32 V DC (SELV) Power consumption: typically 150 mW Connection: Bus terminal (KNX Type 5.1) Protection: IP 20 Safety class: III Mark of approval: KNX/VDE Ambient temperature: 5C ... +45C Storage/transport temperature: 25C ... +70C (storage above +45C results in shorter lifetime) Mounting position: any, recommended: output terminals on top Minimum spacings: none Fastening: on DIN rail 35 x 7.5
5224
2316.16 REGHE KNX SWITCH/BLINDS ACTUATOR ACTUATORS - OUTPUTS
5225 2308.16 REGHM KNX Switch/blinds actuator Switch 8-gang ACTUATORS - OUTPUTS
KNX Switch/blinds actuator Switch 8-gang, Blinds 4-gang The switching actuator receives telegrams from sensors or other controls via the KNX and switches electrical loads by its independent contacts. The relay outputs can be adjusted alternatively to switching or blinds operation by the software. Also a mixed switching/blinds operation is possible. Within the blinds operation, the actuator can operate blinds, shutters, awnings, ventilation flaps, curtains or other drives for 230V AC. In the switching mode it operates e.g. lighting applications or also low voltages. Each output has a line voltage supplied mono stabile relay. This way also preferred positions can be adjusted even at bus voltage drop. By means of the 4 push-buttons on top of the device, the relays can be operated by hand in parallel to the KNX without bus voltage or programming. Within the blinds operation mode, the functional scope includes separate adjustable driving times, advanced acknowledge functions, assignments to up to 5 safety functions, an extensive sun protection as well as scenarios and forced position functions. Also a central control of all blinds outputs is possible. Within the switching mode, the functional scope for each output channel includes extensive time functions, logics, scenarios or inhibit-functions and advanced acknowledge functions. Also the central switching of all outputs is possible. For projecting and commissioning the use of ETS 3.0d is recommended. Only with this ETS version or later versions the full functionality will be available (vd4-file). For ETS2 and older versions of ETS3 separate databases are available (vd2-file).
5225
2308.16 REGHM KNX SWITCH/BLINDS ACTUATOR SWITCH 8-GANG ACTUATORS - OUTPUTS
5226 2308.16 REGHE KNX Switch/blinds actuator Switch 8-gang, Blinds 4-gang ACTUATORS - OUTPUTS
KNX Switch/blinds actuator Switch 8-gang, Blinds 4-gang The switching actuator receives telegrams from sensors or other controls via the KNX and switches electrical loads by its independent contacts. The relay outputs can be adjusted alternatively to switching or blinds operation by the software. Also a mixed switching/blinds operation is possible. Within the blinds operation, the actuator can operate blinds, shutters, awnings, ventilation flaps, curtains or other drives for 230V AC. In the switching mode it operates e.g. lighting applications or also low voltages. Each output has a line voltage supplied mono stabile relay. This way also preferred positions can be adjusted even at bus voltage drop. By means of the 4 push-buttons on top of the device, the relays can be operated by hand in parallel to the KNX without bus voltage or programming. Within the blinds operation mode, the functional scope includes separate adjustable driving times, advanced acknowledge functions, assignments to up to 5 safety functions, an extensive sun protection as well as scenarios and forced position functions. Also a central control of all blinds outputs is possible. Within the switching mode, the functional scope for each output channel includes extensive time functions, logics, scenarios or inhibit-functions and advanced acknowledge functions. Also the central switching of all outputs is possible. For projecting and commissioning the use of ETS 3.0d is recommended. Only with this ETS version or later versions the full functionality will be available (vd4-file). For ETS2 and older versions of ETS3 separate databases are available (vd2-file).
5226
2308.16 REGHE KNX SWITCH/BLINDS ACTUATOR SWITCH 8-GANG, BLINDS 4-GANG ACTUATORS - OUTPUTS
5227 2308.16 REGCHM Switch actuator with C-load, 8-gang ACTUATORS - OUTPUTS
KNX Devices Switch actuator with C-load, 8-gang with current detection Rail mounting device, 8 units 8 make contacts with manual mechanical operation and status indicator For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Output Product type: Binary output KNX supply: 21 ... 32 V DC Wiring, KNX: KNX bus connection block Wiring, outputs: screw terminals single wire: 0.5 ... 4 mm2 stranded without ferrule: 0.5 ... 4 mm2 stranded with ferrule: 0.5 ... 2.5 mm2 Switch type: make contact, potential-free (?-contact) Relay type: bistable Switching capacities Contact rating: 16 A / 230 V AC 1 Switching capacity: acc. to DIN 60669 16 A / 200 ?F acc. to DIN 60947-4-1 AC 1 16 A acc. to DIN 60947-4-1 AC 3 16 A ohmic load: 3600 W Incandescent lamps: 3600 W HV halogen lamps: 3600 W LV halogen lamps with: - TRONIC transformer: 2500 W - conventional transformer: 2000 W Fluorescent lamps non-compensated: 3600 W Fluorescent lamps compensated: 2500 W Fluorescent lamps lead-lag circuit: 2500 W Manufacturer: JUNG Ref.-no.: 2308.16 REGCHM
5227
2308.16 REGCHM SWITCH ACTUATOR WITH C-LOAD, 8-GANG ACTUATORS - OUTPUTS
5228 2304.16 REGHM Switch actuator, 4-gang ACTUATORS - OUTPUTS
KNX Devices Switch actuator, 4-gang Rail mounting device, 4 units 4 make contacts with manual mechanical operation and status indicator ETS product family: Output Product type: Binary output KNX supply: 21 ... 32 V DC Wiring, KNX: KNX bus connection block Wiring, outputs: screw terminals single wire: 0.5 ... 4 mm2 stranded without ferrule: 0.5 ... 4 mm2 stranded with ferrule: 0.5 ... 2.5 mm2 Switch type: make contact, potential-free (?-contact) Relay type: bistable Switching capacities Contact rating: 16 A/230 V AC 1 ohmic load: 3600 W Incandescent lamps: 2500 W HV halogen lamps: 2500 W LV halogen lamps with: - TRONIC transformer: 1500 W - conventional transformer: 1200 W Fluorescent lamps non-compensated: 2500 W Fluorescent lamps compensated: 1300 W Fluorescent lamps lead-lag circuit: 2300 W Manufacturer: JUNG Ref.-no.: 2304.16 REGHM
5228
2304.16 REGHM SWITCH ACTUATOR, 4-GANG ACTUATORS - OUTPUTS
5229 2142 REG KNX Devices / Line coupler SYSTEM DEVICES
KNX Devices Line coupler Rail mounting device, 2 rail units ETS product family: System components Product type: Line coupler Function: The coupler connects two KNX lines together and guarantees electrical isolation between these lines. The exact function of the device is defined by the address and the selected application. Line coupler: Connection of a line and a main line with or without a filter function. The coupler is physically assigned to the secondary line (here: line). Backbone coupler: Connection of a main line and a backbone line with or without a filter function. The coupler is physically assigned to the secondary line (here: main line). Amplifier: Preparation and repetition of telegrams on a line, no filter function. Subdivision of a line into max. 4 independent line segments = max. 3 line repeaters per line connected in parallel. A separate power supply including a choke is required for each line segment. Power supply: 21 ... 32 V DC via the primary line Current consumption superordinate line: approx. 6 mA subordinate line: approx. 8 mA Wiring: KNX bus connection block for primary and secondary line Mounting: on DIN rail Ambient temperature: - 5 °C ... + 45 °C Storing temperature: - 25 °C ... + 70 °C Protection level: IP 20 acc. EN 60 529 Protection class: III acc. EN 61 140 Mounting width: 36 mm (2 rail units) Manufacturer: JUNG Ref.-no.: 2142 REG
5229
2142 REG KNX DEVICES / LINE COUPLER SYSTEM DEVICES
5230 2304.16 REGCHM Switch actuator with C-load, 4-gang ACTUATORS - OUTPUTS
KNX Devices Switch actuator with C-load, 4-gang with current detection Rail mounting device, 4 units 4 make contacts with manual mechanical operation and status indicator For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Output Product type: Binary output KNX supply: 21 ... 32 V DC Wiring, KNX: KNX bus connection block Wiring, outputs: screw terminals single wire: 0.5 ... 4 mm2 stranded without ferrule: 0.5 ... 4 mm2 stranded with ferrule: 0.5 ... 2.5 mm2 Switch type: make contact, potential-free (?-contact) Relay type: bistable Switching capacities Contact rating: 16 A / 230 V AC 1 Switching capacity: acc. to DIN 60669 16 A / 200 ?F acc. to DIN 60947-4-1 AC 1 16 A acc. to DIN 60947-4-1 AC 3 16 A ohmic load: 3600 W Incandescent lamps: 3600 W HV halogen lamps: 3600 W LV halogen lamps with: - TRONIC transformer: 2500 W - conventional transformer: 2000 W Fluorescent lamps non-compensated: 3600 W Fluorescent lamps compensated: 2500 W Fluorescent lamps lead-lag circuit: 2500 W Manufacturer: JUNG Ref.-no.: 2304.16 REGCHM
5230
2304.16 REGCHM SWITCH ACTUATOR WITH C-LOAD, 4-GANG ACTUATORS - OUTPUTS
5448 2214 REG A KNX ANALOG INPUT 2214 REGA INPUTS
KNX analog input 2214 REGA ETS-product family: Input Product type: 4-gang analog input Series embodiment (SE)-device (4 units) The analog input processes measured-value data supplied by analog sensors. Four analog transducers in any combination can be connected to the input. The analog input evaluates voltage and current signals. Voltage signals: 0 ... 1 V DC 0 ... 10 V DC Current signals: 0 ... 20 mA DC 4 ... 20 mA DC The 4 ... 20 mA current inputs can be monitored for open-circuit conditions. The following sensors from the JUNG range can be connected to the analog input: Brightness (WS 10 H), Twilight (WS 10 D), Temperature (WS 10 T), Wind (WS 10 W) and Rain (WS 10 R). An optional analog input extension module, ref.-no. 2214 REGAM, connected by a 6-pole system connector adds four more analog sensor inputs to the device. A 6-pole connector can be used for future extensions. The measured values are encoded by the analog input in the form of value telegrams (DPT 9.0xx, 2 byte or DPT 5.001, 1 byte) so that other bus subscribers (e.g. visualization software, Info Display) can display these measured values, generate messages or intervene in automatic control processes. Each measured value has two presettable limit values. As soon as a measured value rises above or drops below these limits, the analog input can transmitt the corresponding messages. The limit values can also be modified in operation by other devices as, for instance, a push-button sensor serving as a value transmitter. The analog input needs 24 V AC for operation. This voltage can be supplied, for instance, by the power supply unit (WSSV 10). This power supply unit can at the same time also supply the power for wind sensor heating or the power for a connected analog input extension module. The terminals US and GND supply 24 V DC (max. 100 mA altogether) to external analog sensors. In the event of short-circuits or overload between US and GND, the power is shut off. KNX analog input 2214 REGA ETS-product family: Input Product type: 4-gang analog input Series embodiment (SE)-device (4 units) The analog input processes measured-value data supplied by analog sensors. Four analog transducers in any combination can be connected to the input. The analog input evaluates voltage and current signals. Voltage signals: 0 ... 1 V DC 0 ... 10 V DC Current signals: 0 ... 20 mA DC 4 ... 20 mA DC The 4 ... 20 mA current inputs can be monitored for open-circuit conditions. The following sensors from the JUNG range can be connected to the analog input: Brightness (WS 10 H), Twilight (WS 10 D), Temperature (WS 10 T), Wind (WS 10 W) and Rain (WS 10 R). An optional analog input extension module, ref.-no. 2214 REGAM, connected by a 6-pole system connector adds four more analog sensor inputs to the device. A 6-pole connector can be used for future extensions. The measured values are encoded by the analog input in the form of value telegrams (DPT 9.0xx, 2 byte or DPT 5.001, 1 byte) so that other bus subscribers (e.g. visualization software, Info Display) can display these measured values, generate messages or intervene in automatic control processes. Each measured value has two presettable limit values. As soon as a measured value rises above or drops below these limits, the analog input can transmitt the corresponding messages. The limit values can also be modified in operation by other devices as, for instance, a push-button sensor serving as a value transmitter. The analog input needs 24 V AC for operation. This voltage can be supplied, for instance, by the power supply unit (WSSV 10). This power supply unit can at the same time also supply the power for wind sensor heating or the power for a connected analog input extension module. The terminals US and GND supply 24 V DC (max. 100 mA altogether) to external analog sensors. In the event of short-circuits or overload between US and GND, the power is shut off. Technical data KNX Supply Voltage: 21 - 32 V DC (SELV) Power consumption: typically 150 mW Connection: Bus terminal (KNX Typ 5.1) External supply, voltage: 24 V AC ± 10 % Current consumption: 250 mA max. Power consumption: max. 4 VA Connection: Screw terminals: 0.5 mm2 to 4 mm2, single-wire 0.34 mm2 to 4 mm2, fine-wire (without ferrule) 0.14 mm2 to 2.5 mm2, fine wire (incl. ferrule) Response to voltage failure Bus voltage only: No communication with KNX. Operating voltage only: No communication with KNX, no feeding of the measuring sensors. Bus and mains/operating voltage: No communication with KNX, no feeding of the measuring sensors. Response to recovery Bus voltage only: No communication with KNX, no feeding of the measuring sensors. Operating voltage only: No communication with KNX. Bus and mains/operating voltage: Communication with KNX according to initialization parameters. Module connection Numbers: 1 Connection: 6-pole system connector for analog input extension module Analog inputs Number: 4 Signal voltage/current: 0 ... 1 V DC, 0 ... 10 V DC, 0 ... 20 mA DC or 4 ... 20 mA DC, depending on parameterization Input resistance: Voltage measurement: approx. 18 kO Current measurement: approx. 100 O Connection: Screw terminals: 0.5 mm2 to 4 mm2, single-wire 0.34 mm2 to 4 mm2, fine-wire (without ferrule) 0.14 mm2 to 2.5 mm2, fine-wire (incl. ferrule) Measuring sensor power supply outputs Number: 2 Rated voltage: 24 V DC ±10 % Rated current: 100 mA DC (total) Connection: Screw terminals: 0.5 mm2 to 4 mm2, single-wire 0.34 mm2 to 4 mm2, fine-wire (without ferrule) 0.14 mm2 to 2.5 mm2, fine-wire (incl. ferrule) Protection: IP 20 Safety class: III Mark of approval: KNX/VDE Ambient temperature: -5°C ... +45°C Storage/transport temperature: -25°C ... +70°C (storage above +45°C reduces the lifetime) Mounting position: any Minimum distances: none Fastening: on DIN rail 35 x 7.5
5448
2214 REG A KNX ANALOG INPUT 2214 REGA INPUTS
5449 2204.01 REGA KNX Analog Output 4fold 2204.01REGA ACTUATORS - OUTPUTS
KNX analog output 2204.01 REGA ETS-product family: Output Product type: 4-gang analog output Series embodiment (SE)-device (4 units) The analog output converts measuring data received via KNX telegrams (DPT-ID 9.0xx and 5.010) into analog output signals. The analog output signals enable heating, ventilation and air conditioning units to adapt their output values to information received from the bus and thus to take part in control processes. Voltage signals: 0 ... 1 V DC 0 ... 10 V DC Current signals: 0 ... 20 mA DC 4 ... 20 mA DC The analog output offers four analog outputs which can be software-parameterised for one of the ranges mentioned above. Outputs not used can be deactivated. The output variables can be force-controlled from a coordinating control system. With an analog output extension module, the number of analog outputs can be increased from 4 to 8. In conjunction with the dimming function of a sensor, both, the analog output and also the analog output extension module can be used as an active control unit for dimming applications. The analog output needs 24 V AC for operation. The necessary power can be supplied by the power supply unit (WSSV 10). This power supply unit is capable of supplying power at the same time to a connected analog output extension module. 131
5449
2204.01 REGA KNX ANALOG OUTPUT 4FOLD 2204.01REGA ACTUATORS - OUTPUTS
5450 2178 TS KNX ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
KNX Devices Room temperature controller with integrated BCU with integrated push-button interface 4-gang with rotary knob for set point adjustment For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature Status LED: comfort mode (green) standby mode (green) night mode (green) dew point (red) frost/heat protection (red) energy request (yellow) operation mode heating (red) operation mode cooling (blue) 1 presence push-button 4 binary inputs. 2 channels can be used alternatively as independent outputs, max. 0,8 mA. Terminals: Sensor cable at terminal 1 - 5 (binary inputs and outputs): J-Y(St)Y 4 x 2 x 0,6 mm2 max. 5 m Temperature sensor (terminal 5 - 6): ready-made connecting cable 2 x 0.75 mm2 The sensor connection can be extended to 50 m max. by using cable 2 x 1.5 mm2 Achtung: Werden generell Leitungen mit einem Querschnitt von 1,5 mm2 verwendet, Schalterabzweigdose einsetzen! Type of loads (binary outputs): LED or electronic relay, max. 0.8 mA, DC 5 V Output value: max. 0.8 mA per output channel (at 1.5 V, typ. for red low-current LED) Colour: ivory
5450
2178 TS KNX ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
5451 2178 ORTS KNX Objektregler m. Tasters 2178ORTS CLIMATE CONTROL
KNX room temperature controller with integrated BCU and push-button interface ETS-product family: Heating, A/C, vent. or binary input, 4-gang Product type: Regulator all ranges as above The temperature controller with integrated BCU is used for a single room temperature control. Dependent on the operation mode and the actual temperature it controls a heating or cooling system by the KNX. It is possible to choose between different control principles as a continuous PI control, switching PI control (pulse width modulation) and a switching two-step control. The actual room temperature can be measured either by the integrated temperature sensor or by an external one which is connected to channel 4 of the integrated push-button interface. In addition to the basic system for heating or cooling, an additional heating or cooling system can be implemented whereby the control principles can be different. This is practicable when a room should be heated up faster due to cold temperatures (basic system: floor heating; additional system: electrical heating). The temperature controller knows five operation modes which are comfort, stand-by, night, frost / heat protection and disabled regulator. The integrated 4-gang push-button interface has similar features as the regular 2-/4-gang push-button interface (? please refer to ref.-no. 2076-2T / 4T). In addition, channel 4 can also be used to connect an external sensor, e.g. floor temperature sensor. The connection of 230 V signals or other external voltages to the inputs is not allowed. The temperature controller is also available in a version without any operational element as rotary knob, presence push-button or LED's. This version is called autostat. The functions of the autostat are exactly the same, it is operated solely via bus telegrams. This version is recommended for e.g. for public buildings where you should avoid the manual operation of the sensor.
5451
2178 ORTS KNX OBJEKTREGLER M. TASTERS 2178ORTS CLIMATE CONTROL
7814 98 Accessories and spare parts, Plug-in glow lamp 400V 0,5mA 98 SIN FAMILIA
Accessories and spare parts Plug-in glow lamp for 1-gang switch insert ref.-no.: 503 U, 603 W, 803 W for 1-gang switch insert with indicator light ref.-no.: 501-20 KOU, 502-20 KOU, 506-20 KOU, 503 KOU, 803 KOW average life approx. 40,000 h Version: 400 V, 0.5 mA Manufacturer: JUNG Ref.-no.: 98
7814
98 ACCESSORIES AND SPARE PARTS, PLUG-IN GLOW LAMP 400V 0,5MA 98 SIN FAMILIA
8216 2224 WH KNX weather station "home" SENSORS
The KNX weather station detects the meteorological data "Wind speed", "Precipitation", "Twilight", "Temperature" and the brightness in three directions. Its main area of application is the automatic, weather-dependent control of shading. It is specially designed for use in homes. To increase functional reliability, the weather station monitors itself in some important functions, and reports any corresponding errors to the bus automatically via indicator objects. It is intended for outdoor installation on a mast or on a wall. The bus coupling to the KNX/EIB is integrated (monoblock).Evaluation of the data themselves, in particular the limiting value processing, is performed already in the weather station. A built-in heater protects against degradation of function from frost and moisture condensation down to -20 °C. The heating system further ensures that the sensor surface of the precipitation sensor will dry off quickly after rain, and also melts snow and ice. Power is supplied to the unit via the bus, except for the heating system and the power supply for the precipitation sensor. The weather station requires an external 24 V AC/DC power supply for the heating system, without which precipitation detection is not possible. Logic gates are available for cascading a number of weather stations and for linking the limiting values and the monitoring functions. Blocking elements make it possible to block individual functions at the installation location. Designated use measurement and evaluation of weather data: wind speed, precipitation, twilight, temperature and brightness vertical mounting on the outside of buildings, preferably on roofs and at façades Product features integrated KNX bus coupler compact housing low-maintenance device measured-value acquisition and limit value monitoring The power supply ref.-no.: WSSV 10 is necessary for precipitation detection.
8216
2224 WH KNX WEATHER STATION "HOME" SENSORS
8346 93 Glimmlampe 230V 1,1 mA 93 SIN FAMILIA
für SCHUKO-Steckdosen mit Funktionsanzeige 230 V, 1,1 mA
8346
93 GLIMMLAMPE 230V 1,1 MA 93 SIN FAMILIA
8347 94 Glimmlampe 230V 0,8 mA 94 SIN FAMILIA
Glimmlampe für Schalter und Taster 230 V, 0,8 mA
8347
94 GLIMMLAMPE 230V 0,8 MA 94 SIN FAMILIA
8358 2302.16 REGHM Switch actuator, 2-gang ACTUATORS - OUTPUTS
Rail mounting device, 4 rail units 2 make contacts with manual mechanical operation and status indicator ETS product family: Output Product type: Binary output
8358
2302.16 REGHM SWITCH ACTUATOR, 2-GANG ACTUATORS - OUTPUTS
8362 FUS 4410 BR Magnet contact ALARMS CENTRAL
8362
FUS 4410 BR MAGNET CONTACT ALARMS CENTRAL
8628 4071 TSM Standard push-button module with BCU, 1-gang PUSH BUTTONS
When a button is pressed, and depending on the loaded application and the parameters pro-grammed, the push button sensor Standard TSM transmits telegrams to the KNX / EIB. These can be, for instance, telegrams for switching or momentary-contact control, for dimming or for shutter control. It is also possible to program value transmitter functions such as dimming value transmitters or light scene extensions. The 1-gang Standard TSM push button sensor consists of one large control surface, which is in-terrupted in the middle by an LED photoconductor. In the "Switching" application of the ETS, the control concept of this control surface can be configured as a rocker function or as a button function. The control concept is defined as a rocker in the "Dimming", "Blind" and "Value trans-mitter, scene extension" applications. With the rocker function, the control surface is divided into two actuation pressure points with the same basic function. With the button function, the control surface is evaluated as two functionally-different actuation pressure points (two buttons). The Standard TSM push button sensor possesses a status LED. This status LED can optionally either be permanently on or off, or otherwise act as an actuation or status indicator for a button or a rocker. If necessary, an operation LED can optionally serve as an orientation light. If the push button is in Programming mode, the operation LED flashes with a frequency of about 8 Hz. If there is no (suitable) application loaded in the push button, the operation LED flashes to indicate an error at a frequency of approx. 0.75 Hz and the push button sensor does not work. A bus coupling unit is already permanently integrated in the Standard TSM push button sensor, allowing the device to be connected directly to the bus cable during commissioning.
8628
4071 TSM STANDARD PUSH-BUTTON MODULE WITH BCU, 1-GANG PUSH BUTTONS
8629 4072 TSM Standard push-button module with integrated BCU, 2-gang PUSH BUTTONS
When a button is pressed, and depending on the loaded application and the parameters pro-grammed, the push button sensor Standard TSM transmits telegrams to the KNX / EIB. These can be, for instance, telegrams for switching or momentary-contact control, for dimming or for shutter control. It is also possible to program value transmitter functions such as dimming value transmitters or light scene extensions.The double Standard TSM push button sensor consists of two control surfaces. In the "Switch-ing" application of the ETS, the control concept of one control surface can be configured as a rocker function or as a button function. The control concept is defined as a rocker in the "Dim-ming", "Blind" and "Value transmitter, scene extension" applications. With the rocker function, one control surface is divided into two actuation pressure points with the same basic function. With the button function, one control surface is evaluated as two functionally-different actuation pressure points (two buttons).The Standard TSM push button sensor is equipped with one status LED per control surface. One status LED can optionally either be permanently on or off, or otherwise act as an button-press or status indicator for a button or a rocker.If necessary, an operation LED can optionally serve as an orientation light. If the push button is in Programming mode, the operation LED flashes with a frequency of about 8 Hz. If there is no (suitable) application loaded in the push button, the operation LED flashes to indicate an error at a frequency of approx. 0.75 Hz and the push button sensor does not work.A BCU is already permanently integrated in the Standard TSM push button sensor, allowing the device to be connected directly to the bus cable during commissioning.
8629
4072 TSM STANDARD PUSH-BUTTON MODULE WITH INTEGRATED BCU, 2-GANG PUSH BUTTONS
8630 4073 TSM Standard push-button module with integrated BCU, 3-gang PUSH BUTTONS
When a button is pressed, and depending on the loaded application and the parameters pro-grammed, the push button sensor Standard TSM transmits telegrams to the KNX / EIB. These can be, for instance, telegrams for switching or momentary-contact control, for dimming or for shutter control. It is also possible to program value transmitter functions such as dimming value transmitters or light scene extensions.The triple Standard TSM push button sensor consists of three control surfaces. In the "Switch-ing" application of the ETS, the control concept of one control surface can be configured as a rocker function or as a button function. The control concept is defined as a rocker in the "Dim-ming", "Blind" and "Value transmitter, scene extension" applications. With the rocker function, one control surface is divided into two actuation pressure points with the same basic function. With the button function, one control surface is evaluated as two functionally-different actuation pressure points (two buttons).The Standard TSM push button sensor is equipped with one status LED per control surface. One status LED can optionally either be permanently on or off, or otherwise act as a button-press or status indicator for a button or a rocker.If necessary, an operation LED can optionally serve as an orientation light. If the push button is in Programming mode, the operation LED flashes with a frequency of about 8 Hz. If there is no (suitable) application loaded in the push button, the operation LED flashes to indicate an error at a frequency of approx. 0.75 Hz and the push button sensor does not work.A BCU is already permanently integrated in the Standard TSM push button sensor, allowing the device to be connected directly to the bus cable during commissioning.
8630
4073 TSM STANDARD PUSH-BUTTON MODULE WITH INTEGRATED BCU, 3-GANG PUSH BUTTONS
8631 4074 TSM Standard push-button module with BCU, 4-gang PUSH BUTTONS
When a button is pressed, and depending on the loaded application and the parameters pro-grammed, the push button sensor Standard TSM transmits telegrams to the KNX / EIB. These can be, for instance, telegrams for switching or momentary-contact control, for dimming or for shutter control. It is also possible to program value transmitter functions such as dimming value transmitters or light scene extensions.The 4x Standard TSM push button sensor consists of four control surfaces. In the "Switching" application of the ETS, the control concept of one control surface can be configured as a rocker function or as a button function. The control concept is defined as a rocker in the "Dimming", "Blind" and "Value transmitter, scene extension" applications. With the rocker function, one con-trol surface is divided into two actuation pressure points with the same basic function. With the button function, one control surface is evaluated as two functionally-different actuation pressure points (two buttons).The Standard TSM push button sensor is equipped with one status LED per control surface. One status LED can optionally either be permanently on or off, or otherwise act as a button-press actuation or status indicator for a button or a rocker.If necessary, an operation LED can optionally serve as an orientation light. If the push button is in Programming mode, the operation LED flashes with a frequency of about 8 Hz. If there is no (suitable) application loaded in the push button, the operation LED flashes to indicate an error at a frequency of approx. 0.75 Hz and the push button sensor does not work.A BCU is already permanently integrated in the Standard TSM push button sensor, allowing the device to be connected directly to the bus cable during commissioning.
8631
4074 TSM STANDARD PUSH-BUTTON MODULE WITH BCU, 4-GANG PUSH BUTTONS
8641 4094 TSEM Universal push-button extension module PUSH BUTTONS
for cover kit 4-gang, complete, ref.-no.: .. 404 TSA .. for cover 4-gang with symbols, ref.-no.: .. 404 TSAP .. provides an additional 4-gang push-button as extension of a universal push-button module preferred installation: vertical 8 red LED: status indication
8641
4094 TSEM UNIVERSAL PUSH-BUTTON EXTENSION MODULE PUSH BUTTONS
8736 CD 403 TSA Cover kit 3-gang, complete wait PUSH BUTTONS
Covers for push-button modules Cover kit 3-gang, complete to clip on push-button module 3-gang: Standard, ref.-no.: 4073 TSM Universal, ref.-no.: 4093 TSM 24 V AC/DC, ref.-no.: 4236 TSM
8736
CD 403 TSA COVER KIT 3-GANG, COMPLETE WAIT PUSH BUTTONS
8752 CD 404 TSA Cover kit 4-gang, complete white PUSH BUTTONS
Covers for push-button modules Cover kit 4-gang, complete to clip on push-button module 4-gang: Standard, ref.-no.: 4074 TSM Universal, ref.-no.: 4094 TSM Universal push-button extension module, ref.-no.: 4094 TSEM 24 V AC/DC, ref.-no.: 4248 TSM
8752
CD 404 TSA COVER KIT 4-GANG, COMPLETE WHITE PUSH BUTTONS
8757 CD 404 TSAP 14 Cover 4-gang with symbols white PUSH BUTTONS
Covers for push-button modules Cover 4-gang with symbols to exchange the top left cover of the cover kit 3-gang ref.-no.: CD 403 TSA.. and top left and bottom right cover of the cover kit 4-gang ref.-no.: CD 404 TSA.. for completion the adapter frame ref-no. CD 4 AR is required!
8757
CD 404 TSAP 14 COVER 4-GANG WITH SYMBOLS WHITE PUSH BUTTONS
8762 CD 404 TSAP 23 Cover 4-gang with symbols whait PUSH BUTTONS
Covers for push-button modules Cover 4-gang with symbols to exchange the bottom left cover of the cover kit 3-gang ref.-no.: CD 403 TSA.. and top right and bottom left cover of the cover kit 4-gang ref.-no.: CD 404 TSA.. for completion the adapter frame ref-no. CD 4 AR is required
8762
CD 404 TSAP 23 COVER 4-GANG WITH SYMBOLS WHAIT PUSH BUTTONS
8796 A 2178 KNX room temperature controller CLIMATE CONTROL
KNX room temperature controller with integrated BCU ETS-product family: Heating, A/C, ventilation Product type: Regulator ranges CD 500/CD plus The temperature controller with integrated BCU is used for a single room temperature control. Dependent on the operation mode and the actual temperature it controls a heating or cooling system by the KNX. It is possible to choose between different control principles as a continuous PI control, switching PI control (pulse width modulation) and a switching two-step control. The actual room temperature is measured by the integrated temperature sensor. In addition to the basic system for heating or cooling, an additional heating or cooling system can be implemented whereby the control principles can be different. This is practicable when a room should be heated up faster due to cold temperatures (basic system: floor heating; additional system: electrical heating). The temperature controller knows five operation modes which are comfort, stand-by, night, frost / heat protection and disabled controller.
8796
A 2178 KNX ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8799 A 2178 TS Room temperature controller CLIMATE CONTROL
Room temperature controller with integrated BCU with integrated push-button interface 4-gang with rotary knob for set point adjustment For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature Status LED: comfort mode (green) standby mode (green) night mode (green)
8799
A 2178 TS ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8802 A 2178 TS AL Room temperature controller CLIMATE CONTROL
8802
A 2178 TS AL ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8804 A 2178 ORTS Room autostat CLIMATE CONTROL
with integrated BCU with integrated push-button interface 4-gang without rotary knob for set point adjustment without any operational elements For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature 4 binary inputs. 2 channels can be used alternatively as independent outputs, max. 0,8 mA.
8804
A 2178 ORTS ROOM AUTOSTAT CLIMATE CONTROL
8810 2178 Room temperature controller CLIMATE CONTROL
with integrated BCU with rotary knob for set point adjustment For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature
8810
2178 ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8822 LS 2178 Room temperature controller CLIMATE CONTROL
with integrated BCU with rotary knob for set point adjustment For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature Status LED: comfort mode (green) standby mode (green) night mode (green) dew point (red)
8822
LS 2178 ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8830 LS 2178 TS Room temperature controller CLIMATE CONTROL
with integrated BCU with integrated push-button interface 4-gang with rotary knob for set point adjustment For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature
8830
LS 2178 TS ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8835 ES 2178 TS Room temperature controller CLIMATE CONTROL
8835
ES 2178 TS ROOM TEMPERATURE CONTROLLER CLIMATE CONTROL
8838 LS 2178 ORTS Room autostat CLIMATE CONTROL
with integrated BCU with integrated push-button interface 4-gang without rotary knob for set point adjustment without any operational elements For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Phys. sensors Product type: Temperature 4 binary inputs. 2 channels can be used alternatively as independent outputs, max. 0,8 mA.
8838
LS 2178 ORTS ROOM AUTOSTAT CLIMATE CONTROL
8873 ABL/S2.1 Application unit logic CONTROLLERS
Rail mounting device, 2 rail units ETS product family: Controller Product type: Controller can be parameterised via ETS3 50 logical functions (AND, OR, One hot) 50 unidirectional and bidirectional gates 30 timers (with ON/OFF delay, pulse duration, staircase lighting function) 10 comparators
8873
ABL/S2.1 APPLICATION UNIT LOGIC CONTROLLERS
8888 FCA 2 REGHE Fan coil actuator 2-gang CLIMATE CONTROL
Rail mounting device, 4 rail units with manual electronic operation and LED status indication For projecting and commissioning the use of ETS 3.0d is recommended. Only with this version or later versions the full functionality will be available. ETS product family: Heating, A/C, Ventilation Product type: Fan-coil Product features · connection of a fan coil unit with up to 6 fan stages or connection of fan coil units with up to 3 fan stages respectively · manual output control, provisional operation · control options for heating, cooling or combined heating/cooling operation · 2-pipe or 4-pipe operation · individual or hierarchical switching of fan stages · feedback · output state indication · disable function for each channel Modes of operation · Bus operation: operation via touch sensors or room controller · Temporary manual control: manual operation locally with keypad, automatic return to bus operation · Permanent manual control mode: only manual operation locally on device
8888
FCA 2 REGHE FAN COIL ACTUATOR 2-GANG CLIMATE CONTROL
8889 RA 23024 REGHE Room actuator 230 V ACTUATORS - OUTPUTS
Rail mounting device, 4 rail units
with manual electronic operation and LED status indication
For projecting and commissioning the use of ETS 3.0d is recommended.
Only with this version or later versions the full functionality will be available.
ETS product family: Output
Product type: Binary output

Designated use
· Switching of electrical consumers AC 230 V with potential-free contacts
· Switching of electrically operated blinds, shutters, awnings and similar curtains
· Heating outputs: electronic outputs for switching electro-thermal valve drives

Product features
· Manual output control, provisional operation
· Feedback in manual control mode and in bus operation
· Scene function
· Disabling of individual outputs by hand or via the bus

Switching function
· Make-contact and break-contact operation
· Logic operation and forcing function
· Feedback function
· Central switching function with group feedback
· Time functions: ON-delay, OFF-delay, staircase lighting timer with early-warning function

Blind/shutter function
· Suitable for AC motors 230 V
· Direct control of blind/shutter position
· Direct control of slat position
· Checkback of running state, blind/shutter position and slat position
· Forced-control position from primary control
· Safety function: 3 independent wind alarms, rain alarm, frost alarm
· Sun protection function

Control of valve drives 230 V
· Switching or PWM operation
· Control of valve drives with working characteristics "normally open" or "normally closed“
· Overload and short-circuit protection
· Emergency operation in the event of bus failure for summer and winter
· Protection against jamming valves
· Forced-control position

8889
RA 23024 REGHE ROOM ACTUATOR 230 V ACTUATORS - OUTPUTS
8893 2508 REGHE Blinds actuator, 8-gang AC 230 V, 4-gang DC 12-48 V ACTUATORS - OUTPUTS
Rail mounting device, 8 rail units with manual electronic operation and LED status indication Product features - Manual output control, provisional operation - Suitable for AC motors 230 V and DC motors 12...48 V - Automatic run time detection with 230 V AC drives - Direct control of blind/shutter position - Direct control of slat position - Scene function - Checkback of run status, blind/shutter position and slat position for bus and manual operation - Forced top and bottom position from primary control - Safety function: 3 independent wind alarms, rain alarm, frost alarm - Sun protection function
8893
2508 REGHE BLINDS ACTUATOR, 8-GANG AC 230 V, 4-GANG DC 12-48 V ACTUATORS - OUTPUTS
8907 OPC-EDITOR OPC editor VISUALIZATION
KNX Facility Pilot Facility Pilot software Note: The software is locked with a software key and must be activated within 20 days after the installation. System requirements: Windows XP, Internet Explorer 6, DirectX (version 9b), Adobe Reader For the installation under Windows XP administrator rights are required. Adobe Reader, Internet Explorer and DirectX are delivered with the FAP CD-ROM. Recommended order of installation: 1. Internet Explorer 2. DirectX 3. Facility Pilot 4. Adobe Reader Hardware requirements: Pentium IV or equal, min. 1.2 GHz RAM: 256 MB Free space on hard disc: 40 GB (depending on the data processing / archives) Resolution: 1024 x 768 Colours: min. 16 bit per pixel Interface: serial or USB for the application of FALCON Internet connection: (optional) when e-mail notification is used Version: OPC editor Manufacturer: JUNG Ref.-no.: OPC-EDITOR
8907
OPC-EDITOR OPC EDITOR VISUALIZATION
9927 4092 TSEM Universal push-button extension module 2 gang PUSH BUTTONS
for the extension of up to 4 additional push-buttons for the devices: * Universal push-button module * RCD Compact module preferred installation: vertical Adapter frames are included in delivery: ref.-no. LS 4 AR for LS design ranges (pre-mounted) and ref.-no. CD 4 AR for CD 500 red LED: status indication
9927
4092 TSEM UNIVERSAL PUSH-BUTTON EXTENSION MODULE 2 GANG PUSH BUTTONS
9928 4093 TSEM Universal push-button extension module 3 gang PUSH BUTTONS
for the extension of up to 4 additional push-buttons for the devices: * Universal push-button module * RCD Compact module preferred installation: vertical Adapter frames are included in delivery: ref.-no. LS 4 AR for LS design ranges (pre-mounted) and ref.-no. CD 4 AR for CD 500 red LED: status indication
9928
4093 TSEM UNIVERSAL PUSH-BUTTON EXTENSION MODULE 3 GANG PUSH BUTTONS
10113 2501 UP Flush-mounted blinds actuator, 1-gang with satellite input ACTUATORS - OUTPUTS
3 binary inputs ETS product family: Shutter Product type: Shutter Product characteristics Switching of venetian blinds, awnings and similar hangings with AC 110 ... 230 V~ Installation into standard wall box with Ø 60 mm Terminals for connection are included Three binary inputs for floating contacts, can be used as satellite inputs for local control Power supply via bus, no additional power supplay necessary Blinds function Direct control of blind position Direct control of louvre angle Feedback of movement, blind position and louvre position Forced position by superior control Security function: 3 independent wind alarms, rain alarm, frost alarm Sun protection function
10113
2501 UP FLUSH-MOUNTED BLINDS ACTUATOR, 1-GANG WITH SATELLITE INPUT ACTUATORS - OUTPUTS
10170 4093 KRM TS D Room controller display compact module CLIMATE CONTROL
Adapter frames are included in delivery: ref.-no. LS 4 AR for LS design ranges (pre-mounted) and ref.-no. CD 4 AR for CD 500 recommended mounting height: 1.5 m Intended use · Measurement and feedback control of the room temperature · Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc. · Installation in wall box according to DIN 49 073 Product characteristics · All buttons can be assigned with functions for controller operation. · Four red status LEDs · A blue operation LED as an orientation light and to indicate the programming status · Integrated bus coupling unit · Connection of push-button extension module · Integrated room temperature sensor · Room temperature control with setpoint value specification · Display of room or setpoint temperature · Display of outdoor temperature - with external sensor, e.g. weather station · Display of time, in conjunction with KNX time encoder · Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc. · Push-button function or rockers function, vertical or horizontal
10170
4093 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE CLIMATE CONTROL
10311 2504 REGHER Shutter actuator 4-gang AC 230 V ACTUATORS - OUTPUTS
Rail mounting device, 4 rail units with manual electronic operation and LED status indication ETS product family: Shutter Product type: Shutter
10311
2504 REGHER SHUTTER ACTUATOR 4-GANG AC 230 V ACTUATORS - OUTPUTS
13167 A 2178 ORTS CH Room autostat with integrated BCU with integrated push-button interface 4-gang without rotary knob for set point adjustment CLIMATE CONTROL
Room autostat with integrated BCU with integrated push-button interface 4-gang without rotary knob for set point adjustment

without any operational elements
Only with the ETS 3.0d version or later versions the full functionality will be available.
ETS product family: Heating, A/C, ventilation
Product type: Regulator

13167
A 2178 ORTS CH ROOM AUTOSTAT WITH INTEGRATED BCU WITH INTEGRATED PUSH-BUTTON INTERFACE 4-GANG WITHOUT ROTARY KNOB FOR SET POINT ADJUSTMENT CLIMATE CONTROL
10694 IPS 100 REG Ethernet interface for bus system GATEWAYS

Ethernet interface for bus system Bus system EIB/KNX, Model Ethernet interface, Mounting method DRA, Width in number of modular spacings 2, With LED indication, Operating voltage 24V, Protocol Other,

10694
IPS 100 REG ETHERNET INTERFACE FOR BUS SYSTEM GATEWAYS
10803 CO2 A 2178 CO2 multi-sensor with humidity sensor and room temperature controller SENSORS

CO2 multi-sensor with humidity sensor and room temperature controller
Intended use

  • Measurement of CO2 concentration, relative air humidity and air temperature
  • Output of the measured values as telegram to the bus, e.g. for controlling fans or window drives via KNX telegrams
  • Single-room temperature control in KNX installations
  • Installation in appliance box according to DIN 49073
Product characteristics
  • Limit value monitoring for CO2 concentration (max. 4 threshold values) and air humidity (max. 2 threshold values)
  • Dew point alarm e.g. for cooling blankets and conservatories, to avoid mould formation
  • Two binary inputs for connection of floating contacts e.g. buttons, switches, window contacts
  • Logic gates for simple gating functions

Technical data  
Rated voltage KNX:DC 21 ... 32 V SELV 
Current consumption KNX:typical 12.5 mA
max. 25 mA (4 s/15 s as a cycle) 
Connection, KNX:terminal 
Protection class:III 
Ambient temperature:–5 ... +45 °C 
Binary inputs  
 Cable length:max. 5 m 
 Cable type:J-Y(St)Y 2 x 2 x 0.8 mm2 
CO2 sensor  
 Measuring range:0 ... 2000 ppm 
Humidity sensors  
 Measuring range:10 ... 95 % relative humidity (r. h.) 
Temperature sensors  
 Measuring range:–5 ... +45 °C 
10803
CO2 A 2178 CO2 MULTI-SENSOR WITH HUMIDITY SENSOR AND ROOM TEMPERATURE CONTROLLER SENSORS
10805 CO2 A 2178 AL CO2 multi-sensor with humidity sensor and room temperature controller, A500 SENSORS
CO2 multi-sensor with humidity sensor and room temperature controller

Intended use
  • Measurement of CO2 concentration, relative air humidity and air temperature
  • Output of the measured values as telegram to the bus, e.g. for controlling fans or window drives via KNX telegrams
  • Single-room temperature control in KNX installations
  • Installation in appliance box according to DIN 49073


Product characteristics

  • Limit value monitoring for CO2 concentration (max. 4 threshold values) and air humidity (max. 2 threshold values)
  • Dew point alarm e.g. for cooling blankets and conservatories, to avoid mould formation
  • Two binary inputs for connection of floating contacts e.g. buttons, switches, window contacts
  • Logic gates for simple gating functions

Technical data  
Rated voltage KNX:DC 21 ... 32 V SELV 
Current consumption KNX:typical 12.5 mA
max. 25 mA (4 s/15 s as a cycle) 
Connection, KNX:terminal 
Protection class:III 
Ambient temperature:–5 ... +45 °C 
Binary inputs  
 Cable length:max. 5 m 
 Cable type:J-Y(St)Y 2 x 2 x 0.8 mm2 
CO2 sensor  
 Measuring range:0 ... 2000 ppm 
Humidity sensors  
 Measuring range:10 ... 95 % relative humidity (r. h.) 
Temperature sensors  
 Measuring range:–5 ... +45 °C 
10805
CO2 A 2178 AL CO2 MULTI-SENSOR WITH HUMIDITY SENSOR AND ROOM TEMPERATURE CONTROLLER, A500 SENSORS
11080 CO2 CD 2178 CO2 multi-sensor with humidity sensor and room temperature controller SENSORS
Intended use
  • Measurement of CO2 concentration, relative air humidity and air temperature
  • Output of the measured values as telegram to the bus, e.g. for controlling fans or window drives via KNX telegrams
  • Single-room temperature control in KNX installations
  • Installation in appliance box according to DIN 49073


Product characteristics

  • Limit value monitoring for CO2 concentration (max. 4 threshold values) and air humidity (max. 2 threshold values)
  • Dew point alarm e.g. for cooling blankets and conservatories, to avoid mould formation
  • Two binary inputs for connection of floating contacts e.g. buttons, switches, window contacts
  • Logic gates for simple gating functions

Technical data  
Rated voltage KNX:DC 21 ... 32 V SELV 
Current consumption KNX:typical 12.5 mA
max. 25 mA (4 s/15 s as a cycle) 
Connection, KNX:terminal 
Protection class:III 
Ambient temperature:–5 ... +45 °C 
Binary inputs  
 Cable length:max. 5 m 
 Cable type:J-Y(St)Y 2 x 2 x 0.8 mm2 
CO2 sensor  
 Measuring range:0 ... 2000 ppm 
Humidity sensors  
 Measuring range:10 ... 95 % relative humidity (r. h.) 
Temperature sensors  
 Measuring range:–5 ... +45 °C 
11080
CO2 CD 2178 CO2 MULTI-SENSOR WITH HUMIDITY SENSOR AND ROOM TEMPERATURE CONTROLLER SENSORS
11156 2424 REGHE Blinds actuator, 4-gang DC 12-48 V ACTUATORS - OUTPUTS
Rail mounting device, 4 rail units
with manual electronic operation and LED status indication
Only with the ETS 3.0d version or later versions the full functionality will be available.
ETS product family: Shutter
Product type: Shutter

 
Intended use
  • Switching of electrically driven Venetian blinds, rolling shutters, awnings and similar hangings for AC 230 V mains voltage or DC 12...48 V extra-low voltage.
  • Mounting on DIN rail in distribution boxes

 
Product characteristics
  • Outputs can be operated manually, construction site mode
  • Suitable for 230 V AC motors and 12...48 V DC motors
  • Automatic operation time detection possible with 230 V drives
  • Hanging position directly controllable
  • Slat position directly controllable
  • Light scene function
  • Acknowledgement of movement state, hanging position and slat position in bus and manual operation.
  • Top and bottom forced position via higher-level controller
  • Safety function: 3 independent wind alarms, rain alarm, frost alarm
  • Sun protection function
  • Integration into building temperature management is possible
  • Disabling of individual outputs manually or via bus

Technical data  
Outputs:4 independent channels for one blind/shutter motor each 
Contact type:floating make contact 
Switching voltage DC:DC 12 ... 48 V 
Breaking capacity DC 12 V:6 A 
Breaking capacity DC 24 V:6 A 
Breaking capacity DC 48 V:3 A 
Min. switching current DC:100 mA 
Connection:screw terminals 
 single wire:0.5 ... 4 mm2 
 stranded without ferrule:0.5 ... 4 mm2 
 stranded with ferrule:0.5 ... 2.5 mm2 
11156
2424 REGHE BLINDS ACTUATOR, 4-GANG DC 12-48 V ACTUATORS - OUTPUTS
11157 2502 REGHE Blinds actuator, 2-gang AC 230 V, 1-gang DC 12-48 V ACTUATORS - OUTPUTS
Rail mounting device, 4 rail units
with manual electronic operation and LED status indication
Only with the ETS 3.0d version or later versions the full functionality will be available.
ETS product family: Shutter
Product type: Shutter

Intended use
  • Switching of electrically driven Venetian blinds, rolling shutters, awnings and similar hangings for AC 230 V mains voltage or DC 12...48 V extra-low voltage.
  • Mounting on DIN rail in distribution boxes

 
Product characteristics
  • Outputs can be operated manually, construction site mode
  • Suitable for 230 V AC motors and 12...48 V DC motors
  • Automatic operation time detection possible with 230 V drives
  • Hanging position directly controllable
  • Slat position directly controllable
  • Light scene function
  • Acknowledgement of movement state, hanging position and slat position in bus and manual operation.
  • Top and bottom forced position via higher-level controller
  • Safety function: 3 independent wind alarms, rain alarm, frost alarm
  • Sun protection function
  • Integration into building temperature management is possible
  • Disabling of individual outputs manually or via bus

Technical data  
Outputs:2 channels AC 230 V, 1 channel DC 12...48 V  
Power supply mains:AC 230/240 V ~, 50/60 Hz 
Connection:screw terminals 
 single wire:0.5 ... 4 mm2 
 stranded without ferrule:0.5 ... 4 mm2 
 stranded with ferrule:0.5 ... 2.5 mm2 
Breaking capacity AC1:6 A (230 V) 
Switching current DC 12/24 V:6 A 
Switching current DC 48 V:3 A 
Max. blind/shutter running time:20 min 
Power loss:max. 4.5 W 
Ambient temperature:–5 ... +45 °C 
Storing temperature:–25 ... +70 °C 
Approvals:VDE 
11157
2502 REGHE BLINDS ACTUATOR, 2-GANG AC 230 V, 1-GANG DC 12-48 V ACTUATORS - OUTPUTS
12244 ME 3180-1 A AT PIR observer 180°, universal DETECTORS
ETS product family: Physical sensors
Product type: Movement
A slide switch (ON/AUTO/OFF) is integrated.
The device has three potentiometers for time, brightness and sensitivity adjustable from the front side
(time, brightness ± 50% adjustable, basic settings via ETS).
sesitivity approx. 20 ... 100 %

The KNX universal automatic switch is plugged onto a flush-mounted bus coupling unit. It reacts to changes in temperature as people are moving into the detection area. This causes switching commands or value transmission to devices such as binary outputs to switch light or dimming actuators. It can also be used to release light scenes in combination with a light scene control unit.
The universal automatic switch is equipped with three potentiometers for time, brightness and sensitivity adjustable from the front side. A slide switch (ON/AUTO/OFF) is also integrated. It has two major operation modes. One mode for lighting purposes as explained and one mode for monitoring purposes used for simple alarm detection or in combination with the Central Alarm Unit EAM 4000. By activating a specific object the device can be toggled between the two modes.
The universal automatic switch has a detection angle of 180°. This angle can be restricted to 90° with a slip-on screen.

Two different universal automatic switches are available:
  • Device for 1.1 m mounting height (ref-no: ..3180-1 A..)
  • Device for 2.2 m mounting height (ref-no: ..3280-1 A..)

The universal automatic switch has three applications:
  • PIR single unit for stand-alone installation
  • PIR master unit for master/extension installation (e.g. long corridor)
  • PIR extension unit for master/extension installation
    In connection with the KNX system, the functionality of this device depends on software. Detailed information on loadable software and attainable functionality as well as the software itself can be obtained from the manufacturer’s product database.
    An updated version of the product database and the technical descriptions are available at http://gb.jung.de
12244
ME 3180-1 A AT PIR OBSERVER 180°, UNIVERSAL DETECTORS
12247 ME 3180 C PIR observer 180°,1,10 m, standard of wall DETECTORS
for bus coupling unit ref.-no.: 2070 U
ETS product family: Physical sensors
Product type: Movement
sesitivity approx. 20 ... 100 %, adjustable with potentiometer

The KNX standard automatic switch is plugged onto a flush-mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180°. This angle can be restricted to 90° with a slip-on screen.

Two different standard automatic switches are available:
  • Device for 1.1 m mounting height (ref-no: ..3180..)
  • Device for 2.2 m mounting height (ref-no: ..3280..)

The standard automatic switch has three applications:
  • PIR single unit for stand-alone installation
  • PIR master unit for master/extension installation (e.g. long corridor)
  • PIR extension unit for master/extension installation
    In connection with the KNX system, the functionality of this device depends on software. Detailed information on loadable software and attainable functionality as well as the software itself can be obtained from the manufacturer’s product database.
    An updated version of the product database and the technical descriptions are available at http://gb.jung.de
12247
ME 3180 C PIR OBSERVER 180°,1,10 M, STANDARD OF WALL DETECTORS
12251 ME 3280 AT PIR observer 180, standard DETECTORS
for bus coupling unit ref.-no.: 2070 U
ETS product family: Physical sensors
Product type: Movement
sesitivity approx. 20 ... 100 %, adjustable with potentiometer

The KNX standard automatic switch is plugged onto a flush-mounted bus coupling unit. It reacts to changes in temperature like people moving into the detection area. This causes switching commands to devices such as binary outputs to switch groups of lights. The automatic switch has a detection angle of 180°. This angle can be restricted to 90° with a slip-on screen.

Two different standard automatic switches are available:
  • Device for 1.1 m mounting height (ref-no: ..3180..)
  • Device for 2.2 m mounting height (ref-no: ..3280..)

The standard automatic switch has three applications:
  • PIR single unit for stand-alone installation
  • PIR master unit for master/extension installation (e.g. long corridor)
  • PIR extension unit for master/extension installation
In connection with the KNX system, the functionality of this device depends on software. Detailed information on loadable software and attainable functionality as well as the software itself can be obtained from the manufacturer’s product database.
An updated version of the product database and the technical descriptions are available at http://gb.jung.de
12251
ME 3280 AT PIR OBSERVER 180, STANDARD DETECTORS
12350 CO2 AL 2178 CO2 multi-sensor with humidity sensor and room temperature controller SENSORS
LS ranges
CO2 multi-sensor with humidity sensor and room temperature controller.
12350
CO2 AL 2178 CO2 MULTI-SENSOR WITH HUMIDITY SENSOR AND ROOM TEMPERATURE CONTROLLER SENSORS
12378 MBT 2424 KNX glass panel, 24 capacitive sensor buttons and 24 status LEDs. PUSH BUTTONS
The glass panel with aluminium housing is equipped with 24 capacitive sensor buttons and 24 status LEDs.
The panel enables the control of switching, dimming and push-button functions as well as light scene and value transmitter functions. The LEDs can be separately parameterised to be illuminated in green, red or blue to signalise different situations of the KNX installation. Single sensor buttons, full columns or the entire panel can be blocked with blocking functions. Acoustic signals when pushing the sensor buttons can be parameterised. The surface can be labelled with exchangeable labelling foils, which can be labelled with the JUNG label tool.
The MBT 2424 will be installed into a 2-gang wall box or a surface-mounted housing. Programming takes place via ETS. A drilling template and a bit for assembling will be delivered with the device.
12378
MBT 2424 KNX GLASS PANEL, 24 CAPACITIVE SENSOR BUTTONS AND 24 STATUS LEDS. PUSH BUTTONS
12740 3904 REGHE Universal dimming actuator, 4-gang, 4 x 250 W, HV LED lamps typ. 4 x 7 ... 50 W, 1 x 950 W ACTUATORS - OUTPUTS
Intended use
  • Switching and dimming of incandescent lamps, HV halogen lamps and Tronic-Transformers with halogen lamps or dimmable inductive transformers with halogen or LED lamps, HV-LED lamps and compact fluorescent lamp
  • Mounting on DIN rail according to EN 60715 in distribution boxes

Product characteristics
  • Automatic or manual selection of the dimming principle suitable for the load
  • Protected against no-load, short-circuit and overheating
  • Signal in the event of a short-circuit
  • Outputs can be operated manually
  • Feedback of the switching position and the dimming value
  • Parameterisable switch-on and dimming behaviour
  • Time functions: switch-on delay, switch-off delay, staircase lighting timer with pre-warning function
  • Light scene operation
  • Disabling of individual outputs manually or via bus
  • Status indicator of the outputs via LED
  • Operating hours counter
  • Mains failure longer than approx. 5 seconds leads to switch-off of the dimmer actuator. Depending on the parameter setting, the connected load is calibrated after resumption of power supply.
  • Increase in output power possible through parallel switching of multiple outputs (max. 950 W)
12740
3904 REGHE UNIVERSAL DIMMING ACTUATOR, 4-GANG, 4 X 250 W, HV LED LAMPS TYP. 4 X 7 ... 50 W, 1 X 950 W ACTUATORS - OUTPUTS
12742 3901 REGHE Universal dimming actuator / speed regulator, 1 x 500 W ACTUATORS - OUTPUTS
Intended use
  • Switching and dimming of incandescent lamps, HV halogen lamps and Tronic-Transformers with halogen lamps or dimmable inductive transformers with halogen or LED lamps, HV-LED lamps and compact fluorescent lamp
  • Mounting on DIN rail according to EN 60715 in distribution boxes
  • Speed controller for regulating the speed of single-phase motors e.g. induction motors, shaded pole motors or universal motors

Product characteristics
  • Automatic or manual selection of the dimming principle suitable for the load
  • Protected against no-load, short-circuit and overheating
  • Signal in the event of a short-circuit
  • Outputs can be operated manually
  • Feedback of the switching position and the dimming value
  • Parameterisable switch-on and dimming behaviour
  • Time functions: switch-on delay, switch-off delay, staircase lighting timer with pre-warning function
  • Light scene operation
  • Disabling of individual outputs manually or via bus
  • Status indicator of the outputs via LED
  • Operating hours counter
  • Mains failure longer than approx. 5 seconds leads to switch-off of the dimmer actuator. Depending on the parameter setting, the connected load is calibrated after resumption of power supply.
12742
3901 REGHE UNIVERSAL DIMMING ACTUATOR / SPEED REGULATOR, 1 X 500 W ACTUATORS - OUTPUTS
12746 DS 4092 TS Rotary sensor, integrated BCU, integrated push-button interface 3-gang, push-button function and acoustic signal CONTROLLERS
Function: switching, dimming, shutter control, value transmitter, scene extension
12746
DS 4092 TS ROTARY SENSOR, INTEGRATED BCU, INTEGRATED PUSH-BUTTON INTERFACE 3-GANG, PUSH-BUTTON FUNCTION AND ACOUSTIC SIGNAL CONTROLLERS
12775 3361 WW Presence detector with integrated BCU, 3 PIR sensors 360°, Standartçd DETECTORS
Product characteristics
  • Integrated bus coupling unit
  • 3 PIR sensors
  • Detection field 360° (3 x 120°)
  • Integrated brightness sensor
  • Deployed as presence detector, motion detector, or for alert operation
  • Output functions: Switching, staircase function, switching with forced position, value transmitter, light scene extension, operating mode setting for room temperature controller
  • Detection area extendible by parallel switching of several devices as main unit or extension unit
  • Manual sensitivity adjustment
  • Status LED: Flashes during motion detection; depending on programming in normal operation or only during the walking test mode

Additional characteristics of "Universal" version:
  • Manual operation with IR remote control possible (ref.-no.: KNX PM FB IR)
  • 5 function blocks for motion or presence detection each with 2 outputs
  • Function blocks switchable, e.g. for day/night operation
  • PIR sensors can be evaluated separately
  • Brightness sensor function with 3 limiting values
  • Light control with max. of 3 channels, setpoint shift in operation, separate configuration of dimming-up, control and dimming-down phase
  • Light control can be combined with presence detector function

Presence detector function:
  • Detection of the smallest motions e.g. at a workplace for detecting the presence of persons
  • Switch on: Motion detection and brightness threshold not reached
  • Switch off: No motion in the detection field and shut-off delay elapsed or brightness threshold exceeded

Motion detector function:
  • Motion detection for passageways in buildings
  • Switch on: Motion detection and brightness threshold not reached
  • Switch off: No motion in the detection field and shut-off delay elapsed
  • After reacting and switching on, the motion detection works independently of the brightness.

Signalling mode:
  • Brightness-independent detection of motions in the detection field
  • Switch on: After detection of an adjustable number of motions within the set monitoring period
  • Switch off: No persons in the detection field and shut-off delay elapsed
12775
3361 WW PRESENCE DETECTOR WITH INTEGRATED BCU, 3 PIR SENSORS 360°, STANDARTÇD DETECTORS
12883 SC 1000 KNX Smart Control KNX, including KNX module VISUALIZATION
Intended use
  • Operating loads and displaying the status of systems and information e.g. light switching, dimming, controlling blinds/shutters, temperature and consumption values etc.
  • Operation with power supply (ref.-no.: NT 2405 VDC or NT 2415 REG VDC)
  • Installation indoors in 2 flush-mounted appliance boxes according to DIN 49073

Product characteristics
  • Illuminated programmable colour screen TFT, 800 x 480 pixels, 16.7 million colours, WVGA
  • Vertical installation flush with the wall
  • Capacitive touchscreen, operation via touch directly on the glass surface
  • Integrated card reader for microSD cards (for future extensions)
  • Integrated loudspeaker (for future extensions)
  • External loudspeaker module connectable (accessory, for future extensions)
  • Insert with KNX module
  • External pushbutton extension module connectable (via KNX module)
  • Operating functions switching, dimming, controlling blinds, valuators, calling up light scenes, etc.
  • Integrated room temperature sensor
  • Integrated brightness sensor
  • Room temperature control with setpoint value specification
  • Display of room temperature, setpoint temperature and outdoor temperature, time and weekday etc.
12883
SC 1000 KNX SMART CONTROL KNX, INCLUDING KNX MODULE VISUALIZATION
12893 2531 UP Flush-mounted room climate interface with satellite input ACTUATORS - OUTPUTS
3 binary inputs
1 blinds output, 1 output "TRIAC" (heating)

Product characteristics
  • Switching of venetian blinds, awnings and similar hangings with AC 230 V~
  • Switching of electrothermal valve drives
  • Installation into standard wall box with Ø 60 mm
  • Terminals for connection are included
  • Three binary inputs for floating contacts, can be used as satellite inputs for local control
  • Power supply via bus, no additional power supply necessary

Blinds function
  • Direct control of blind position
  • Direct control of louvre angle
  • Feedback of movement, blind position and louvre position
  • Forced position by superior control
  • Security function: 3 independent wind alarms, rain alarm, frost alarm
  • Sun protection function

Function of valve drives
  • ON/OFF operation mode or PWM operation mode
  • Valve drive types "normally open" or "normally closed" can be controlled
  • Overload-proof, short-circuit proof
  • Protection against blocked valves
  • Forced position
  • Cyclical monitoring of input signals can be parameterized

PWM operation mode: electrothermal valve drives have only 2 positions: "open" and "closed". The PWM mode has a quasi-continuous behaviour by means of switching ON and OFF during the cycle time of the valve drive.
12893
2531 UP FLUSH-MOUNTED ROOM CLIMATE INTERFACE WITH SATELLITE INPUT ACTUATORS - OUTPUTS
12895 3902 REGHE Universal dimming actuator, 2-gang x 300 W ACTUATORS - OUTPUTS
2 x 300 W, HV LED lamps typ. 2 x 7 ... 60 W
Rail mounting device, 4 rail units
ETS product family: Illumination
Product type: Dimmer

Intended use
  • Switching and dimming of incandescent lamps, HV halogen lamps and Tronic-Transformers with halogen lamps or dimmable inductive transformers with halogen or LED lamps, HV-LED lamps and compact fluorescent lamp
  • Mounting on DIN rail according to EN 60715 in distribution boxes

Product characteristics
  • Automatic or manual selection of the dimming principle suitable for the load
  • Protected against no-load, short-circuit and overheating
  • Signal in the event of a short-circuit
  • Outputs can be operated manually
  • Feedback of the switching position and the dimming value
  • Parameterisable switch-on and dimming behaviour
  • Time functions: switch-on delay, switch-off delay, staircase lighting timer with pre-warning function
  • Light scene operation
  • Disabling of individual outputs manually or via bus
  • Status indicator of the outputs via LED
  • Operating hours counter
  • Mains failure longer than approx. 5 seconds leads to switch-off of the dimmer actuator. Depending on the parameter setting, the connected load is calibrated after resumption of power supply.
12895
3902 REGHE UNIVERSAL DIMMING ACTUATOR, 2-GANG X 300 W ACTUATORS - OUTPUTS
12899 4071.02 LED Push-button BCU, neutral position PUSH BUTTONS
Function: switching, dimming, shutter control
LED: always ON, always OFF, status indication

Can operate up to two different groups (with switch function).
Status indication is possible with LED

Depending on the version of the push-button BCU ? 1-gang rocker or 2-gang rocker ? centre plates are used with and without indication lights. The “upper” or “lower” rockers can be controlled with the push-button with “neutral position”, while only the “lower” rocker can be pressed with the push-button with “switch position”. The push-button BCU can only function with an application program i.e. the push-button BCU consists of the device (hardware) and the application program (software).
12899
4071.02 LED PUSH-BUTTON BCU, NEUTRAL POSITION PUSH BUTTONS
12900 2095 LUX Flush-mounted brightness controller SENSORS
Intended use
  • Measurement and control of lighting in interior areas
  • Ceiling installation on fixed ceilings
  • Installation in wall box according to DIN 49073
Function
The brightness controller is used for metering and controlling workspace and room lighting. At the user’s direction, the control can be selected as a switching On/Off control for controlling switch actuators or as a continuous constant light level control for controlling dimming actuators or switch/dimming actuators. The controller has an integrated bus coupling unit with bus connection via a bus terminal. The device is powered from the bus voltage.
The controller is delivered with two white-painted optical fibre rods (one rod with a plane light-sensitive surface and one rod with an oblique (30°) light-sensitive surface). One of these is plugged in by the user. Normally, the optical fibre rod with the plane light-sensitive surface is to be used. If necessary, the direction of the light-collection cone can be shifted by using the optical fibre rod with the oblique light-sensitive surface.
The brightness sensor and the red blinking commissioning LED are under the optical fibre rod.
12900
2095 LUX FLUSH-MOUNTED BRIGHTNESS CONTROLLER SENSORS
12902 8472.02 LED W 2-gang Push-button BCU, neutral position PUSH BUTTONS
Depending on the version of the push-button BCU – 1-gang rocker or 2-gang rocker – center plates are used with and without indication lights.
The “upper” or “lower” rockers can be controlled with the push-button with “neutral position”, while only the “lower” rocker can be pressed with the push-button with “switch position”. The push-button BCU can only function with an application program
i.e. the push-button BCU consists of the device (hardware) and the application program (software).
Function: switching, dimming, shutter control
LED: always ON, always OFF, status indication

Can operate up to four different groups (with switch function).
Status indication is possible with LED
12902
8472.02 LED W 2-GANG PUSH-BUTTON BCU, NEUTRAL POSITION PUSH BUTTONS
12903 2514 REGHE Blinds actuator, 4-gang AC 230 V, 2-gang DC 12-48 V ACTUATORS - OUTPUTS
Intended use
  • Switching of electrically driven Venetian blinds, rolling shutters, awnings and similar hangings for AC 230 V mains voltage or DC 12...48 V extra-low voltage.
  • Mounting on DIN rail in distribution boxes

Product characteristics
  • Suitable for 230 V AC motors and 12...48 V DC motors
  • Automatic operation time detection for 230 V motors can be set
  • Slat position directly controllable
  • Acknowledgement of travelling state and slat position in bus and manual mode
  • Light scene function
  • Top and bottom forced position via higher-level controller
  • Sun protection function
12903
2514 REGHE BLINDS ACTUATOR, 4-GANG AC 230 V, 2-GANG DC 12-48 V ACTUATORS - OUTPUTS
12904 2501 HZ UP Flush-mounted heating actuator, 1-gang with satellite input INPUTS
3 binary inputs
1 output "TRIAC"
ETS product family: Heating, A/C, Ventilation
Product type: Valve

Product characteristics
  • Switching of electrothermal valve drives
  • Installation into standard wall box with Ø 60 mm
  • Terminals for connection are included
  • Three binary inputs for floating contacts, can be used as satellite inputs for local control
  • Power supply via bus, no additional power supplay necessary

Function of valve drives
  • ON/OFF operation mode or PWM operation mode
  • Valve drive types "normally open" or "normally closed" can be controlled
  • Overload-proof, short-circuit proof
  • Protection against blocked valves
  • Forced position
  • Cyclical monitoring of input signals can be parameterized


PWM operation mode: electrothermal valve drives have only 2 positions: "open" and "closed". The PWM mode has a quasi-continuous behaviour by means of switching ON and OFF during the cycle time of the valve drive.

12904
2501 HZ UP FLUSH-MOUNTED HEATING ACTUATOR, 1-GANG WITH SATELLITE INPUT INPUTS
12906 FAPV-SERVER-REG Facility Pilot Server VISUALIZATION
Intended use
  • Operation and visualisation of system statuses and information on building automation
  • Displaying information services
  • Operation with power supply (ref.-no.: NT 2415 REG VDC)
  • Mounting on DIN rail according to EN 60715

Product characteristics
  • DIN rail PC with KNX connection
  • Operating system: Windows® Embedded Standard 2009
  • Integrated graphics card and network adapter
  • Interfaces – accessible from front: Slot for micro SD memory card, 2 x USB (2 x 500 mA)
  • Interfaces – accessible from above: Ethernet, DVI, 2 x USB (1 x 500 mA)
  • Facility Pilot version for RMD server preinstalled
  • Two internal KNX interfaces for simultaneous access to KNX system by local Facility Pilot and remote maintenance from outside

The visualization can be realised in several ways:
  • via a monitor (not supplied) connected directly to the DVI port
  • via devices with Windows XP Professional / Windows 7 and Facility Pilot client connected via LAN
  • via iPhone / iPod Touch / iPad
  • KNX-Process connection via the integrated KNX-Data interface
The second KNX-Data interface is used for remote access to the KNX system.
12906
FAPV-SERVER-REG FACILITY PILOT SERVER VISUALIZATION
13239 4072.01 LED Push-button BCU, switch position PUSH BUTTONS
Function: switching, dimming, shutter control
LED: always ON, always OFF

Can operate up to two different groups (with switch function).
Status indication is possible with LED

Depending on the version of the push-button BCU ? 1-gang rocker or 2-gang rocker ? centre plates are used with and without indication lights. The “upper” or “lower” rockers can be controlled with the push-button with “neutral position”, while only the “lower” rocker can be pressed with the push-button with “switch position”. The push-button BCU can only function with an application program i.e. the push-button BCU consists of the device (hardware) and the application program (software).
13239
4072.01 LED PUSH-BUTTON BCU, SWITCH POSITION PUSH BUTTONS
13379 3361-1 WW Presence detector with integrated BCU, 3 PIR, 360° DETECTORS
Produkteigenschaften
  • Integrierte Busankopplung
  • 3 PIR-Sensoren
  • Erfassungsfeld 360° (3 x 120°)
  • Integrierter Helligkeitssensor
  • Einsatz als Präsenzmelder, Bewegungsmelder, oder für Meldebetrieb
  • Ausgangsfunktionen: Schalten, Treppenhausfunktion, Schalten mit Zwangsstellung, Wertgeber, Lichtszenennebenstelle, Betriebsmodusvorgabe für Raumtemperaturregler
  • Erfassungsbereich erweiterbar durch Parallelschalten mehrerer Geräte als Haupt- und Nebenstelle
  • Einsteller zur manuellen Korrektur der Empfindlichkeit
  • Status-LED: Blinkt bei Bewegungserfassung; je nach Programmierung im normalen Betrieb oder nur während des Gehtest-Betriebs

Zusätzliche Eigenschaften Version "Universal":
  • Manuelle Bedienung mit IR-Fernbedienung möglich (Art.-Nr.: KNX PM FB IR)
  • 5 Funktionsblöcke zur Bewegungs- bzw. Präsenzerfassung mit je 2 Ausgängen
  • Funktionsblöcke umschaltbar, z.B. für Tag-/Nachtbetrieb
  • PIR-Sensoren separat auswertbar
  • Helligkeitssensorfunktion mit 3 Grenzwerten
  • Tageslichtabhängige Lichtregelung mit max. 3 Kanälen, Sollwertverschiebung im Betrieb, separater Konfiguration von Anregel-, Regel- und Abregelphase
  • Lichtregelung mit Präsenzmelderfunktion kombinierbar

Präsenzmelderfunktion:
  • Erfassung kleinster Bewegungen z.B. an einem Arbeitsplatz zur Erkennung der Anwesenheit von Personen
  • Einschalten: Anwesenheit von Personen und Helligkeitsschwelle unterschritten
  • Ausschalten: Keine Personen im Erfassungsfeld und Ablauf der Nachlaufzeit, oder Helligkeitsschwelle überschritten

Bewegungsmelderfunktion:
  • Erfassung von Bewegungen zur Verkehrswegsicherung in Gebäuden
  • Einschalten: Anwesenheit von Personen und Helligkeitsschwelle unterschritten
  • Ausschalten: Keine Personen im Erfassungsfeld und Ablauf der Nachlaufzeit
Nach dem Ansprechen und Einschalten arbeitet die Bewegungserfassung helligkeitsunabhängig.

Meldebetrieb:
  • Helligkeitsunabhängige Erfassung von Bewegungen im Erfassungsfeld
  • Einschalten: Nach Erkennen einer einstellbaren Anzahl Bewegungen innerhalb des eingestellten Überwachungszeitraums
  • Ausschalten: Keine Personen im Erfassungsfeld und Ablauf der Nachlaufzeit


Zubehör:
Schutzkorb Art.-Nr.: SK 180-90 WW

Zubehör:
Aufputz-Gehäuse Art.-Nr.: PM-KAPPE-1PM-KAPPE AL-1
13379
3361-1 WW PRESENCE DETECTOR WITH INTEGRATED BCU, 3 PIR, 360° DETECTORS
13412 LS 5093 TSM Universal push-button module, 3-gang PUSH BUTTONS

Universal push-button module, 3-gang

including transparent cover ref.-no.: LS 50 NA
for cover kit 3-gang, complete, ref.-no.: ..503 TSA .. in the LS design ranges
can be extended by means of a push-button extension module, ref.-no.: LS 509.. TSEM
ETS product family: Push-button
Product type: 3-gang push-button

Intended use

  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073

Product characteristics

  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang



Spare part:
transparent cover ref.-no.: LS 50 NA

Accessories:
Neutral cover ref.-no.: LS 50 NA WLS 50 NA WWLS 50 NA LGLS 50 NA SW,AL 50 NA-LES 50 NA-L, AL 50 NA AN-L, ME 50 NA C-LME 50 NA AT-LME 50 NA D-L

13412
LS 5093 TSM UNIVERSAL PUSH-BUTTON MODULE, 3-GANG PUSH BUTTONS
13437 A 5071 TSM Standard push-button module, 1-gang PUSH BUTTONS
Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit

13437
A 5071 TSM STANDARD PUSH-BUTTON MODULE, 1-GANG PUSH BUTTONS
13444 A 5072 TSM Standard push-button module, 2-gang PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 2-gang, complete, ref.-no.: A 502 TSA ..
ETS product family: Push-button
Product type: 2-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13444
A 5072 TSM STANDARD PUSH-BUTTON MODULE, 2-GANG PUSH BUTTONS
13445 A 5073 TSM Standard push-button module, 3-gang PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 3-gang, complete, ref.-no.: A 503 TSA ..
ETS product family: Push-button
Product type: 3-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit


Spare part:
Transparent cover ref.-no.: A 50 NA

Accessories:
Neutral cover ref.-no.: A 50 NA WA 50 NA WWA 50 NA SWA 50 NA ALA 50 NA CH,A 50 NA MO
13445
A 5073 TSM STANDARD PUSH-BUTTON MODULE, 3-GANG PUSH BUTTONS
13446 A 5074 TSM Standard push-button module, 4-gang PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 4-gang, complete, ref.-no.: A 504 TSA ..
ETS product family: Push-button
Product type: 4-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit

13446
A 5074 TSM STANDARD PUSH-BUTTON MODULE, 4-GANG PUSH BUTTONS
13447 A 5091 TSM KNX Tastsensor-Modul Universal, 1fach PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 1-gang, complete, ref.-no.: A 501 TSA ..
can be extended by means of a push-button extension module, ref.-no.: A 509.. TSEM
ETS product family: Push-button
Product type: 1-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang
13447
A 5091 TSM KNX TASTSENSOR-MODUL UNIVERSAL, 1FACH PUSH BUTTONS
13448 A 5092 TSM Universal push-button module, 2-gang PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 2-gang, complete, ref.-no.: A 502 TSA ..
can be extended by means of a push-button extension module, ref.-no.: A 509.. TSEM
ETS product family: Push-button
Product type: 2-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang


Spare part:
Transparent cover ref.-no.: A 50 NA

Accessories:
Neutral cover ref.-no.: A 50 NA WA 50 NA WWA 50 NA SWA 50 NA ALA 50 NA CH,A 50 NA MO

 

13448
A 5092 TSM UNIVERSAL PUSH-BUTTON MODULE, 2-GANG PUSH BUTTONS
13449 A 5093 TSM Universal push-button module, 3-gang PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 3-gang, complete, ref.-no.: A 503 TSA ..
can be extended by means of a push-button extension module, ref.-no.: A 509.. TSEM
ETS product family: Push-button
Product type: 3-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang

13449
A 5093 TSM UNIVERSAL PUSH-BUTTON MODULE, 3-GANG PUSH BUTTONS
13450 A 5094 TSM Universal push-button module, 4-gang PUSH BUTTONS
including transparent cover ref.-no.: A 50 NA
for cover kit 4-gang, complete, ref.-no.: A 504 TSA ..
can be extended by means of a push-button extension module, ref.-no.: A 509.. TSEM
ETS product family: Push-button
Product type: 4-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang


Spare part:
Transparent cover ref.-no.: A 50 NA

Accessories:
Neutral cover ref.-no.: A 50 NA WA 50 NA WWA 50 NA SWA 50 NA ALA 50 NA CH,A 50 NA MO
13450
A 5094 TSM UNIVERSAL PUSH-BUTTON MODULE, 4-GANG PUSH BUTTONS
13481 CD 5071 TSM Standard push-button module, 1-gang PUSH BUTTONS
including transparent cover ref.-no.: CD 50 NA
for cover kit 1-gang, complete, ref.-no.: CD 501 TSA ..
ETS product family: Push-button
Product type: 1-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit

Spare part:
transparent cover ref.-no.: CD 50 NA

Accessories:
Neutral cover ref.-no.: CD 50 NA WCD 50 NA WWCD 50 NA GRCD 50 NA LG,CD 50 NA SW
13481
CD 5071 TSM STANDARD PUSH-BUTTON MODULE, 1-GANG PUSH BUTTONS
13482 CD 5072 TSM Standard push-button module, 2-gang PUSH BUTTONS
including transparent cover ref.-no.: CD 50 NA
for cover kit 2-gang, complete, ref.-no.: CD 502 TSA ..
ETS product family: Push-button
Product type: 2-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit


Spare part:
transparent cover ref.-no.: CD 50 NA

Accessories:
Neutral cover ref.-no.: CD 50 NA WCD 50 NA WWCD 50 NA GRCD 50 NA LG,CD 50 NA SW
13482
CD 5072 TSM STANDARD PUSH-BUTTON MODULE, 2-GANG PUSH BUTTONS
13483 CD 5073 TSM Standard push-button module, 3-gang PUSH BUTTONS
including transparent cover ref.-no.: CD 50 NA
for cover kit 3-gang, complete, ref.-no.: CD 503 TSA ..
ETS product family: Push-button
Product type: 3-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13483
CD 5073 TSM STANDARD PUSH-BUTTON MODULE, 3-GANG PUSH BUTTONS
13531 CD 5074 TSM Standard push-button module, 4-gang PUSH BUTTONS
Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13531
CD 5074 TSM STANDARD PUSH-BUTTON MODULE, 4-GANG PUSH BUTTONS
13532 CD 5091 TSM Universal push-button module, 1-gang PUSH BUTTONS
Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang
13532
CD 5091 TSM UNIVERSAL PUSH-BUTTON MODULE, 1-GANG PUSH BUTTONS
13533 CD 5092 TSM Universal push-button module, 2-gang PUSH BUTTONS
including transparent cover ref.-no.: CD 50 NA
for cover kit 2-gang, complete, ref.-no.: CD 502 TSA ..
can be extended by means of a push-button extension module, ref.-no.: CD 509.. TSEM
ETS product family: Push-button
Product type: 2-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang
13533
CD 5092 TSM UNIVERSAL PUSH-BUTTON MODULE, 2-GANG PUSH BUTTONS
13534 CD 5093 TSM Universal push-button module, 3-gang PUSH BUTTONS
including transparent cover ref.-no.: CD 50 NA
for cover kit 3-gang, complete, ref.-no.: CD 503 TSA ..
can be extended by means of a push-button extension module, ref.-no.: CD 509.. TSEM
ETS product family: Push-button
Product type: 3-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang
13534
CD 5093 TSM UNIVERSAL PUSH-BUTTON MODULE, 3-GANG PUSH BUTTONS
13535 CD 5094 TSM Universal push-button module, 4-gang PUSH BUTTONS
including transparent cover ref.-no.: CD 50 NA
for cover kit 4-gang, complete, ref.-no.: CD 504 TSA ..
can be extended by means of a push-button extension module, ref.-no.: CD 509.. TSEM
ETS product family: Push-button
Product type: 4-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang
13535
CD 5094 TSM UNIVERSAL PUSH-BUTTON MODULE, 4-GANG PUSH BUTTONS
13565 LS 5071 TSM Standard push-button module, 1-gang PUSH BUTTONS
Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13565
LS 5071 TSM STANDARD PUSH-BUTTON MODULE, 1-GANG PUSH BUTTONS
13580 LS 5072 TSM Standard push-button module, 2-gang PUSH BUTTONS
including transparent cover ref.-no.: LS 50 NA
for cover kit 2-gang, complete, ref.-no.: ..502 TSA .. in the LS design ranges
ETS product family: Push-button
Product type: 2-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13580
LS 5072 TSM STANDARD PUSH-BUTTON MODULE, 2-GANG PUSH BUTTONS
13581 LS 5073 TSM Standard push-button module, 3-gang SIN FAMILIA
including transparent cover ref.-no.: LS 50 NA
for cover kit 3-gang, complete, ref.-no.: ..503 TSA .. in the LS design ranges
ETS product family: Push-button
Product type: 3-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13581
LS 5073 TSM STANDARD PUSH-BUTTON MODULE, 3-GANG SIN FAMILIA
13582 LS 5074 TSM Standard push-button module, 4-gang PUSH BUTTONS
including transparent cover ref.-no.: LS 50 NA
for cover kit 4-gang, complete, ref.-no.: ..504 TSA .. in the LS design ranges
ETS product family: Push-button
Product type: 4-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • To be completed with cover kit
  • One red status LED for a pair of buttons
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Inscription field
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
13582
LS 5074 TSM STANDARD PUSH-BUTTON MODULE, 4-GANG PUSH BUTTONS
13583 LS 5091 TSM Universal push-button module, 1-gang PUSH BUTTONS
including transparent cover ref.-no.: LS 50 NA
for cover kit 1-gang, complete, ref.-no.: ..501 TSA .. in the LS design ranges
can be extended by means of a push-button extension module, ref.-no.: LS 509.. TSEM
ETS product family: Push-button
Product type: 1-gang push-button

Intended use
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073
Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Integrated bus coupling unit
  • Connection for a push-button extension module, 1-4 gang
13583
LS 5091 TSM UNIVERSAL PUSH-BUTTON MODULE, 1-GANG PUSH BUTTONS
13586 LS 5091 TSEM Push-button extension module, 1 fold SIN FAMILIA
including transparent cover ref.-no.: LS 50 NA
for the extension of the Universal push-button module (ref.-no.: LS 509.. TSM) with up to 4 additional push-buttons

Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • One or two functions per button
  • To be completed with cover kit
  • Illuminated inscription field
  • One status LED per button, red, green or blue, adjustable
  • One operation LED as orientation light and programming status – red, green or blue, adjustable
  • Brightness of status LED, operation LED and inscription field adjustable, can be changed during operation, e.g. during night times
  • Measurement of room temperature
  • Extension unit for room temperature controller
  • Inhibit function: Inhibit or function mode change of single or all button functions
  • Alarm function, optional acknowledge by pressing any button
  • Energy saving mode
  • Transparent cover kit (included) for temporary site use without design covers
  • Cable lenghts: max. 30 m, cable type: J-Y(St)Y 2 x 2 x 0.8 mm2
13586
LS 5091 TSEM PUSH-BUTTON EXTENSION MODULE, 1 FOLD SIN FAMILIA
13634 RCD CD 4092 M Room controller display module 2-gang CLIMATE CONTROL
can be extended by means of a push-button extension module, ref.-no.: 409.. TSEM

recommended mounting height: 1.5 m

Intended use
  • Operation of consumers, e.g. lights on/off, dimming, blinds/shutters up/down, brightness values, temperatures, storing and recalling of light scenes etc.
  • Room temperature control
  • Fan coil application with up to 4 fan speeds and auto function
  • LCD display is freely programmable (14 byte string text) with up to 4 pages with up to 3 lines
  • Installation in mounting box according to DIN 49073

Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • Vertical and horizontal key/rocker functions
  • Two red LEDs per control key as status or operation indicators
  • Display of values and texts
  • Running text display for one or two messages with max. 14 characters
  • Integrated room temperature controller
  • Room temperature control with setpoint value preset
  • Display of room temperature and setpoint temperature
  • Indication of outside temperature (only with external sensor)
  • Integrated bus coupling unit
  • In combination with Facitility Pilot "Multi-Room Control": music play control, display of music titles, artists, etc.
  • Display unit for the KNX central alarm unit
  • Connection for a push-button extension module, 1-4 gang
13634
RCD CD 4092 M ROOM CONTROLLER DISPLAY MODULE 2-GANG CLIMATE CONTROL
13635 RCD LS 4092 M Room controller display module 2-gang, Serie LS CLIMATE CONTROL
can be extended by means of a push-button extension module, ref.-no.: 409.. TSEM

recommended mounting height: 1.5 m

Intended use
  • Operation of consumers, e.g. lights on/off, dimming, blinds/shutters up/down, brightness values, temperatures, storing and recalling of light scenes etc.
  • Room temperature control
  • Fan coil application with up to 4 fan speeds and auto function
  • LCD display is freely programmable (14 byte string text) with up to 4 pages with up to 3 lines
  • Installation in mounting box according to DIN 49073

Product characteristics
  • Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
  • Vertical and horizontal key/rocker functions
  • Two red LEDs per control key as status or operation indicators
  • Display of values and texts
  • Running text display for one or two messages with max. 14 characters
  • Integrated room temperature controller
  • Room temperature control with setpoint value preset
  • Display of room temperature and setpoint temperature
  • Indication of outside temperature (only with external sensor)
  • Integrated bus coupling unit
  • In combination with Facitility Pilot "Multi-Room Control": music play control, display of music titles, artists, etc.
  • Display unit for the KNX central alarm unit
  • Connection for a push-button extension module, 1-4 gang
13635
RCD LS 4092 M ROOM CONTROLLER DISPLAY MODULE 2-GANG, SERIE LS CLIMATE CONTROL
13644 RCD CD 4092 TSA Cover kit, complete, 2 fold CLIMATE CONTROL
to clip on room controller display module 2-gang ref.-no.: RCD CD 4092 M
13644
RCD CD 4092 TSA COVER KIT, COMPLETE, 2 FOLD CLIMATE CONTROL
13690 IPS 200 REG knx-IP interface GATEWAYS
Intended use
  • Operation as data interface
  • Mounting on DIN rail in distribution boxes

Product characteristics
  • LED display for KNX communication, Ethernet communication and programming mode
  • Configuration via ETS
  • Max. 4 connections to IP terminal devices, e.g. for simultaneous visualisation and configuration
  • Supply from network line (Power-over-Ethernet acc. to IEEE 802.3af) through separate voltage supply ref.-no. NT 2415 REG VDC or the auxiliary voltage output of the KNX voltage supply
  • Electrical isolation between KNX and IP network
  • Power consumption max. 1 W
13690
IPS 200 REG KNX-IP INTERFACE GATEWAYS
13691 IPR 200 REG KNX IP-Router SYSTEM DEVICES
Rail mounting device, 3 rail units
ETS product family: System components
Product type: IP router

Intended use
  • Connection between KNX devices and PC or other data processing devices via IP
  • Operation as line/area coupler or data interface
  • Mounting on DIN rail in distribution boxes

Product characteristics
  • KNXnet/IP routing for communication between KNX lines, areas and systems via IP network
  • Telegramm forwarding and filtering according to physical address or group address
  • LED display for KNX communication, Ethernet communication and programming mode
  • Configuration via ETS and Telnet
  • SNTP server, with battery backup
  • Commissioning with display support
  • Max. 5 connections to IP terminal devices, e.g. for simultaneous visualisation and configuration
  • Outage message of the KNX system to the IP system
  • Supply from network line (Power-over-Ethernet acc. to IEEE 802.3af) through separate voltage supply ref.-no. NT 2415 REG VDC or the auxiliary voltage output of the KNX voltage supply
  • Electrical isolation between KNX and IP network
  • Power consumption max. 1 W
13691
IPR 200 REG KNX IP-ROUTER SYSTEM DEVICES
13693 2128 REG Binary input, 8-gang INPUTS
Rail mounting device, 4 rail units
8 inputs 12 ... 48 V AC/DC
with status indicator
ETS product family: Input
Product type: Binary input

Intended use
  • Polling of conventional switching or push-button contacts, glass break detectors etc. in KNX systems, for reporting of states, operation of loads, etc.
  • Mounting on DIN rail according to EN 60715 in distribution boxes

Product characteristics
  • Status LED for each input
  • Detection of voltage levels and changes on the input
  • Transmitting the input state to the bus
  • Transmission behaviour freely settable
  • Functions: switching, dimming, blinds up/down, brightness values, temperatures, calling up and saving scenes
  • Inputs can be disabled separately
  • External AC and DC voltages can be connected
  • Auxiliary voltage output for polling potential-free contacts
  • No separate power supply required
  • Separate reference potentials for inputs
13693
2128 REG BINARY INPUT, 8-GANG INPUTS
14678 W 220 WW Observer 220° with digital signal evaluation DETECTORS
Intended use
  • Automatic switching of lighting depending on the thermal movement and ambient brightness.
  • Surface-mounting in indoor and outdoor areas

Product characteristics
  • Digital signal evaluation
  • Moisture-proof
  • Shut-off delay, sensitivity and brightness value adjustable
  • Test operation for checking the detection area
  • Switch light ON or OFF for 4 hours
  • Short-time operation to control signal encoders
  • Sensor head adjustable in 2 axes
  • Self-adhesive cover plate elements for limiting the detection area
  • High protection against ambient light
  • 580 switching segments in 4 layers
  • Separate protection against crawling under
  • Parallel connection of multiple motion detectors possible
  • Manual switch ON possible with push-button, break contact


Important: Energy saving lamps cause high inrush currents which may cause the switch contact to get stuck. Then a reduction of capacity is required! Please check suitability of lamps before installation.
Delay time limitation: Once the detector has switched on, the brightness is no longer evaluated. To prevent the light from remaining permanently on (e.g. beyond dawn) caused by permanent movements, the device is provided with an intelligent limiting function.
The delay time (time the light remains on after detection of the last movement) is selected depending on the real switch-on time:
Switch-on time Delay time (approx)
up to 60 min depending on setting
up to 70 min 4 min
up to 75 min 2 min
up to 80 min 1 min
up to 85 min 30 sec
up to 90 min 15 sec
90 min switching-off
The detector switches off after 90 minutes, at the latest, even if there are still movements in the detection field. Restarting will only be effected if the ambient brightness drops below the preset brightness level and if a movement is detected in the detection field.
14678
W 220 WW OBSERVER 220° WITH DIGITAL SIGNAL EVALUATION DETECTORS
15928 A 5178 TSM Room temperature controller module 2-gang CLIMATE CONTROL
Intended use
  • Single-room temperature control in KNX installations
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, recalling and saving light scenes, etc.
  • Installation in wall box according to DIN 49073

Product characteristics
All buttons can be assigned with push-button sensor functions or functions for controller operation.
  • Measurement of the room temperature
  • Room temperature control with setpoint value specification
  • Extension for room temperature controller
  • Push-button functions switching, dimming, blind control, value transmitter, scene recall, etc.
  • One or two functions per button
  • Completion with cover kit 2-gang
  • Illuminable inscription panel
  • Two red status LEDs per button – red, green or blue adjustable
  • One operation LED as an orientation light and to indicate the programming status – red, green or blue adjustable
  • Brightness of status LED, operation LED and labelling field adjustable; switchable while in operation, e.g. during the night
  • Disabling function: Disable or function switch-over of all or of individual push-button functions
  • Alarm function, optionally with confirmation by pressing any button
  • Energy saving mode (for operation without controller function)
  • Integrated bus coupling unit
  • Connection for a push-button extension module, for expansion with up to eight additional buttons
15928
A 5178 TSM ROOM TEMPERATURE CONTROLLER MODULE 2-GANG CLIMATE CONTROL
15929 CD 5178 TSM Room temperature controller module 2-gang CLIMATE CONTROL
Intended use
  • Single-room temperature control in KNX installations
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, recalling and saving light scenes, etc.
  • Installation in wall box according to DIN 49073

Product characteristics
All buttons can be assigned with push-button sensor functions or functions for controller operation.
  • Measurement of the room temperature
  • Room temperature control with setpoint value specification
  • Extension for room temperature controller
  • Push-button functions switching, dimming, blind control, value transmitter, scene recall, etc.
  • One or two functions per button
  • Completion with cover kit 2-gang
  • Illuminable inscription panel
  • Two red status LEDs per button – red, green or blue adjustable
  • One operation LED as an orientation light and to indicate the programming status – red, green or blue adjustable
  • Brightness of status LED, operation LED and labelling field adjustable; switchable while in operation, e.g. during the night
  • Disabling function: Disable or function switch-over of all or of individual push-button functions
  • Alarm function, optionally with confirmation by pressing any button
  • Energy saving mode (for operation without controller function)
  • Integrated bus coupling unit
  • Connection for a push-button extension module, for expansion with up to eight additional buttons
15929
CD 5178 TSM ROOM TEMPERATURE CONTROLLER MODULE 2-GANG CLIMATE CONTROL
15930 LS 5178 TSM Room temperature controller module 2-gang CLIMATE CONTROL
Intended use
  • Single-room temperature control in KNX installations
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, recalling and saving light scenes, etc.
  • Installation in wall box according to DIN 49073

Product characteristics
All buttons can be assigned with push-button sensor functions or functions for controller operation.
  • Measurement of the room temperature
  • Room temperature control with setpoint value specification
  • Extension for room temperature controller
  • Push-button functions switching, dimming, blind control, value transmitter, scene recall, etc.
  • One or two functions per button
  • Completion with cover kit 2-gang
  • Illuminable inscription panel
  • Two red status LEDs per button – red, green or blue adjustable
  • One operation LED as an orientation light and to indicate the programming status – red, green or blue adjustable
  • Brightness of status LED, operation LED and labelling field adjustable; switchable while in operation, e.g. during the night
  • Disabling function: Disable or function switch-over of all or of individual push-button functions
  • Alarm function, optionally with confirmation by pressing any button
  • Energy saving mode (for operation without controller function)
  • Integrated bus coupling unit
  • Connection for a push-button extension module, for expansion with up to eight additional buttons
15930
LS 5178 TSM ROOM TEMPERATURE CONTROLLER MODULE 2-GANG CLIMATE CONTROL
15931 2336 REG HZ HE Heating actuator, 6-gang CLIMATE CONTROL
Intended use
  • Switching of electrothermal actuators for heaters or cooling ceilings
  • Installation in distribution boxes on DIN rail according to DIN EN 60715

Product characteristics
  • Switching operation or PWM operation
  • Actuators with characteristics opened or closed without power
  • Stellantriebe 230 V oder 24 V ansteuerbar
  • Ausgänge manuell bedienbar, Baustellenbetrieb
  • Rückmeldung im Handbetrieb und im Busbetrieb
  • Sperren einzelner Ausgänge per Hand oder Bus
  • Overload-protected, short circuit-protected; Fehlermeldung mit LED
  • Protection against jamming valves
  • Forced position
  • Various setpoints for forced position or emergency operation in case of bus failure for summer or winter
  • Cyclical monitoring of the input signals can be parameterised
  • Feedback via bus, e.g. in case of mains failure, overload or sensor failure
15931
2336 REG HZ HE HEATING ACTUATOR, 6-GANG CLIMATE CONTROL
15932 2103 REG ES Energy detector, 3-gang, for rail mounting SMART METERING
Produkteigenschaften
Der Energiesensor verfügt über drei Kanäle zum Anschluss von Verbrauchern an bis zu drei Außenleiter mit einem gemeinsamen Nullleiter. Für jeden Kanal können folgende Größen gemessen werden:
  • Spannung (eff.)
  • Stromstärke (eff.)
  • Wirkleistung
  • Blindleistung

Zusätzlich werden Wirkleistung und Blindleistung über alle Kanäle aufsummiert und als Drehstromgrößen sowie die Netzfrequenz bereitgestellt.
Entsprechend der Parametrierung werden die Messwerte zyklisch und / oder bei Änderung bzw. bei expliziter Anforderung auf den KNX-Bus gesendet. Zusätzlich ist für einige Größen das Senden eines Telegramms beim Über- und Unterschreiten eines Grenzwerts vorgesehen.

Für jeden Kanal und für die Drehstromgrößen existieren folgende Zählwerke:
  • 1 x Energiezähler gesamt
  • 1 x Energiezähler ¼-h-Wert
  • 3 x Energiezähler n
  • 3 x Energiezwischenzähler n
15932
2103 REG ES ENERGY DETECTOR, 3-GANG, FOR RAIL MOUNTING SMART METERING
16031 A 1540 KO5 Centre plate with knob and lens for rotary sensor ref.-no.: DS 4092 TS PUSH BUTTONS
Centre plate with knob and lens for rotary sensor ref.-no.: DS 4092 TS
16031
A 1540 KO5 CENTRE PLATE WITH KNOB AND LENS FOR ROTARY SENSOR REF.-NO.: DS 4092 TS PUSH BUTTONS
17222 3361-1 M WW Presence detector mini with integrated BCU DETECTORS

Manual operation with IR remote control possible (ref.-no.: KNX PM FB IR)
5 function blocks for motion or presence detection each with 2 outputs
Function blocks switchable, e.g. for day/night operation
PIR sensors can be evaluated separately
Brightness sensor function with 3 limiting values
Light control with max. 3 channels, setpoint shift in operation, separate configuration of dimming-up, control and dimming-down phase
Light control can be combined with presence detector function

Presence detector function:
Detection of the smallest motions e.g. at a workplace for detecting the presence of persons
Switch on: Motion detection and brightness threshold not reached
Switch off: No motion in the detection field and shut-off delay elapsed or brightness threshold exceeded

Motion detector function:
Motion detection for passageways in buildings
Switch on: Motion detection and brightness threshold not reached
Switch off: No motion in the detection field and shut-off delay elapsed
After reacting and switching on, the motion detection works independently of the brightness.

Signalling mode:
Brightness-independent detection of motions in the detection field
Switch on: After detection of an adjustable number of motions within the set monitoring period
Switch off: No persons in the detection field and shut-off delay elapsed

17222
3361-1 M WW PRESENCE DETECTOR MINI WITH INTEGRATED BCU DETECTORS
17226 LS 5194 KRM TS D Room controller display compact module 4-gang CLIMATE CONTROL

Room controller display compact module 4-gang

for cover kit 4-gang, complete, ref.-no.: ..504 TSA .. in the LS range
can be extended by means of a room controller extension module, ref.-no.: LS 5178 TSEM
can be extended by means of a push-button extension module, ref.-no.: LS 509.. TSEM

recommended mounting height: 1.5 m
Intended use
Measurement and feedback control of the room temperature
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
Each button can be used for push-button sensor of contoller functions.
Backlit LC display
One or two functons per button
To be completed with cover kit
Eight status LED – red, green or blue
Brightness of status LED and LCD adjustable
Integrated bus coupling unit
Connection of extension modules
Integrated room temperature sensor
External sensor (ref.-no.: FF 7.8) can be connected
Room temperature control with setpoint value specification
Two internal independent controllers for two independent areas – in connection with extension modules
Display of room or set temperature (°C or °F)
Display of outdoor temperature – with external sensor, e.g. weather station
Display of time, in conjunction with KNX time encoder
Push-button function or rocker function
Inhibit function: blocking or change of function of the entire or single button functions
Alarm function, optional with acknowledge by pressing any button
Function symbols can be shown

17226
LS 5194 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE 4-GANG CLIMATE CONTROL
17287 4194 TSM Universal push-button module, 4-gang PUSH BUTTONS

ETS product family: Push-button
Product type: 4-gang push-button
1 blue LED: operation indication
8 red LED: status indication

Intended use

Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
The push-button functions switching, dimming, controlling blinds, valuators, calling up scenes, etc.
To be completed with cover kit
Two red status LEDs for each button
A blue operation LED as an orientation light and to indicate the programming status
Measurement of room temperature
Integrated bus coupling unit
Transparent cover kit (included) for temporary site use without design covers
One, two or three functions per button
Push-button function or rockers function, vertical or horizontal
Connection of push-button extension module to extend the universal push-button sensor module to include four additional buttons

17287
4194 TSM UNIVERSAL PUSH-BUTTON MODULE, 4-GANG PUSH BUTTONS
17288 4192 TSM KNX Tastsensor-Modul Universal, 2fach PUSH BUTTONS

Adapter frames are included in delivery: ref.-no. LS 4 AR for LS range (pre-mounted) and ref.-no. CD 4 AR for CD range. AS / A ranges without adapter frame.
Only with the ETS 3.0d version or later versions the full functionality will be available.
ETS product family: Push-button
Product type: 2-gang push-button
1 blue LED: operation indication
4 red LED: status indication

Intended use
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
The push-button functions switching, dimming, controlling blinds, valuators, calling up scenes, etc.
To be completed with cover kit
Two red status LEDs for each button
A blue operation LED as an orientation light and to indicate the programming status
Measurement of room temperature
Integrated bus coupling unit
Transparent cover kit (included) for temporary site use without design covers
One, two or three functions per button
Push-button function or rockers function, vertical or horizontal
Connection of push-button extension module to extend the universal push-button sensor module to include four additional buttons

17288
4192 TSM KNX TASTSENSOR-MODUL UNIVERSAL, 2FACH PUSH BUTTONS
17493 A 5192 KRM TS D Room controller display compact module 2-gang CLIMATE CONTROL

for cover kit 2-gang, complete, ref.-no.: A 502 TSA ..
can be extended by means of a room controller extension module, ref.-no.:A 5178 TSEM
can be extended by means of a push-button extension module, ref.-no.:A 509.. TSEM

recommended mounting height: 1.5 m
Intended use

Measurement and feedback control of the room temperature
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
Each button can be used for push-button sensor of contoller functions.
Backlit LC display
One or two functons per button
To be completed with cover kit
Eight status LED – red, green or blue
Brightness of status LED and LCD adjustable
Integrated bus coupling unit
Connection of extension modules
Integrated room temperature sensor
External sensor (ref.-no.: FF 7.8) can be connected
Room temperature control with setpoint value specification
Two internal independent controllers for two independent areas – in connection with extension modules
Display of room or set temperature (°C or °F)
Display of outdoor temperature – with external sensor, e.g. weather station
Display of time, in conjunction with KNX time encoder
Push-button function or rocker function
Inhibit function: blocking or change of function of the entire or single button functions
Alarm function, optional with acknowledge by pressing any button

17493
A 5192 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE 2-GANG CLIMATE CONTROL
17498 A 5194 KRM TS D Room controller display compact module 4-gang CLIMATE CONTROL
for cover kit 4-gang, complete, ref.-no.: A 504 TSA ..
can be extended by means of a room controller extension module, ref.-no.:A 5178 TSEM
can be extended by means of a push-button extension module, ref.-no.:A 509.. TSEM

recommended mounting height: 1.5 m
Intended use
  • Measurement and feedback control of the room temperature
  • Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
  • Installation in wall box according to DIN 49073

Product characteristics
Each button can be used for push-button sensor of contoller functions.
  • Backlit LC display
  • One or two functons per button
  • To be completed with cover kit
  • Eight status LED – red, green or blue
  • Brightness of status LED and LCD adjustable
  • Integrated bus coupling unit
  • Connection of extension modules
  • Integrated room temperature sensor
  • External sensor (ref.-no.: FF 7.8) can be connected
  • Room temperature control with setpoint value specification
  • Two internal independent controllers for two independent areas – in connection with extension modules
  • Display of room or set temperature (°C or °F)
  • Display of outdoor temperature – with external sensor, e.g. weather station
  • Display of time, in conjunction with KNX time encoder
  • Push-button function or rocker function
  • Inhibit function: blocking or change of function of the entire or single button functions
  • Alarm function, optional with acknowledge by pressing any button
17498
A 5194 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE 4-GANG CLIMATE CONTROL
17503 A 5178 TSEM Room controller extension module 2-gang SIN FAMILIA

for cover kit 2-gang, complete, ref.-no.: A 502 TSA ..
for the extension of a room controller module (ref.-no.: A 5192 KRM TS D, A 5194 KRM TS D) with a second room temperature control unit

Intended use
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Measurement of room temperature
Extension for room controller modules (.. 5192 KRM TS D, .. 5194 KRM TS D)
Installation in wall box according to DIN 49073
Cable lenghts: max. 30 m, cable type: J-Y(St)Y 2 x 2 x 0.8 mm2

17503
A 5178 TSEM ROOM CONTROLLER EXTENSION MODULE 2-GANG SIN FAMILIA
17507 CD 5192 KRM TS D Room controller display compact module 2-gang SIN FAMILIA

for cover kit 2-gang, complete, ref.-no.: CD 502 TSA ..
can be extended by means of a room controller extension module, ref.-no.: CD 5178 TSEM
can be extended by means of a push-button extension module, ref.-no.: CD 509.. TSEM

recommended mounting height: 1.5 m
Intended use
Measurement and feedback control of the room temperature
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
Each button can be used for push-button sensor of contoller functions.
Backlit LC display
One or two functons per button
To be completed with cover kit
Eight status LED – red, green or blue
Brightness of status LED and LCD adjustable
Integrated bus coupling unit
Connection of extension modules
Integrated room temperature sensor
External sensor (ref.-no.: FF 7.8) can be connected
Room temperature control with setpoint value specification
Two internal independent controllers for two independent areas – in connection with extension modules
Display of room or set temperature (°C or °F)
Display of outdoor temperature – with external sensor, e.g. weather station
Display of time, in conjunction with KNX time encoder
Push-button function or rocker function
Inhibit function: blocking or change of function of the entire or single button functions
Alarm function, optional with acknowledge by pressing any button
Function symbols can be shown

17507
CD 5192 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE 2-GANG SIN FAMILIA
17508 CD 5194 KRM TS D Room controller display compact module 4-gang CLIMATE CONTROL

for cover kit 4-gang, complete, ref.-no.: CD 504 TSA ..
can be extended by means of a room controller extension module, ref.-no.: CD 5178 TSEM
can be extended by means of a push-button extension module, ref.-no.: CD 509.. TSEM

recommended mounting height: 1.5 m
Intended use
Measurement and feedback control of the room temperature
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
Each button can be used for push-button sensor of contoller functions.
Backlit LC display
One or two functons per button
To be completed with cover kit
Eight status LED – red, green or blue
Brightness of status LED and LCD adjustable
Integrated bus coupling unit
Connection of extension modules
Integrated room temperature sensor
External sensor (ref.-no.: FF 7.8) can be connected
Room temperature control with setpoint value specification
Two internal independent controllers for two independent areas – in connection with extension modules
Display of room or set temperature (°C or °F)
Display of outdoor temperature – with external sensor, e.g. weather station
Display of time, in conjunction with KNX time encoder
Push-button function or rocker function
Inhibit function: blocking or change of function of the entire or single button functions
Alarm function, optional with acknowledge by pressing any button
Function symbols can be shown

17508
CD 5194 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE 4-GANG CLIMATE CONTROL
17509 CD 5178 TSEM Room controller extension module 2-gang PUSH BUTTONS

or cover kit 2-gang, complete, ref.-no.: CD 502 TSA ..
for the extension of a room controller module (ref.-no.: CD 5192 KRM TS D, CD 5194 KRM TS D) with a second room temperature control unit

Intended use
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Measurement of room temperature
Extension for room controller modules (.. 5192 KRM TS D, .. 5194 KRM TS D)
Installation in wall box according to DIN 49073
Cable lenghts: max. 30 m, cable type: J-Y(St)Y 2 x 2 x 0.8 mm2

17509
CD 5178 TSEM ROOM CONTROLLER EXTENSION MODULE 2-GANG PUSH BUTTONS
17518 LS 5192 KRM TS D Room controller display compact module 2-gang SIN FAMILIA

an be extended by means of a room controller extension module, ref.-no.: LS 5178 TSEM
can be extended by means of a push-button extension module, ref.-no.: LS 509.. TSEM

recommended mounting height: 1.5 m
Intended use
Measurement and feedback control of the room temperature
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in wall box according to DIN 49073

Product characteristics
Each button can be used for push-button sensor of contoller functions.
Backlit LC display
One or two functons per button
To be completed with cover kit
Eight status LED – red, green or blue
Brightness of status LED and LCD adjustable
Integrated bus coupling unit
Connection of extension modules
Integrated room temperature sensor
External sensor (ref.-no.: FF 7.8) can be connected
Room temperature control with setpoint value specification
Two internal independent controllers for two independent areas – in connection with extension modules
Display of room or set temperature (°C or °F)
Display of outdoor temperature – with external sensor, e.g. weather station
Display of time, in conjunction with KNX time encoder
Push-button function or rocker function
Inhibit function: blocking or change of function of the entire or single button functions
Alarm function, optional with acknowledge by pressing any button
Function symbols can be shown

17518
LS 5192 KRM TS D ROOM CONTROLLER DISPLAY COMPACT MODULE 2-GANG SIN FAMILIA
17519 LS 5178 TSEM Room controller extension module 2-gang PUSH BUTTONS

for cover kit 2-gang, complete, ref.-no.: ..502 TSA .. in the LS range
for the extension of a room controller module (ref.-no.: LS 5192 KRM TS D, LS 5194 KRM TS D) with a second room temperature control unit

Intended use
Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Measurement of room temperature
Extension for room controller modules (.. 5192 KRM TS D, .. 5194 KRM TS D)
Installation in wall box according to DIN 49073
Cable lenghts: max. 30 m, cable type: J-Y(St)Y 2 x 2 x 0.8 mm2

17519
LS 5178 TSEM ROOM CONTROLLER EXTENSION MODULE 2-GANG PUSH BUTTONS
17523 4191 TSM Universal push-button module, 1-gang PUSH BUTTONS

Adapter frames are included in delivery: ref.-no. LS 4 AR for LS range (pre-mounted) and ref.-no. CD 4 AR for CD range. AS / A ranges without adapter frame.
Only with the ETS 3.0d version or later versions the full functionality will be available.
ETS product family: Push-button
Product type: 1-gang push-button
1 blue LED: operation indication
2 red LED: status indication

Intended use

Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in flush-box according to DIN 49073

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Measurement of room temperature
To be completed with cover kit
Two red status LED per button
One blue operation LED as an orientation light and to indicate the programming status
Integrated bus coupling unit
One, two or three functions per button
Push-button function or rocker function, vertical or horizontal
Connection for a push-button extension module, 1-4 gang
Transparent cover kit (included) for temporary site use without design covers

17523
4191 TSM UNIVERSAL PUSH-BUTTON MODULE, 1-GANG PUSH BUTTONS
17524 4193 TSM Universal push-button module, 3-gang PUSH BUTTONS

for cover kit 2-gang, complete, ref.-no.: .. 402 TSA ..
ffür Tastensatz 2fach, komplett, Art.-Nr.: .. 402 TSA ..
for cover kit 3-gang, complete, ref.-no.: .. 403 TSA ..
for cover 2-gang with symbols, ref.-no.: .. 402 TSAP ..
for cover 4-gang with symbols, ref.-no.: .. 404 TSAP ..
can be extended by means of a push-button extension module, ref.-no.: 409.. TSEM
Adapter frames are included in delivery: ref.-no. LS 4 AR for LS range (pre-mounted) and ref.-no. CD 4 AR for CD range. AS / A ranges without adapter frame.
Only with the ETS 3.0d version or later versions the full functionality will be available.
ETS product family: Push-button
Product type: 3-gang push-button
1 blue LED: operation indication
6 red LED: status indication

Intended use


Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values, temperatures, calling up and saving light scenes, etc.
Installation in flush-box according to DIN 49073

Product characteristics

Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Measurement of room temperature
To be completed with cover kit
Two red status LED per button
One blue operation LED as an orientation light and to indicate the programming status
Integrated bus coupling unit
One, two or three functions per button
Push-button function or rocker function, vertical or horizontal
Connection for a push-button extension module, 1-4 gang
Transparent cover kit (included) for temporary site use without design covers

17524
4193 TSM UNIVERSAL PUSH-BUTTON MODULE, 3-GANG PUSH BUTTONS
17530 A 5071 RF TSM KNX RF radio transmitter module 1-gang RF

Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 1-gang push-button
1 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
Transparent cover ref.-no.: A 50 NA

Accessories:
Neutral cover ref.-no.: A 50 NA W, A 50 NA WW, A 50 NA SW, A 50 NA AL, A 50 NA CH, A 50 NA MO

17530
A 5071 RF TSM KNX RF RADIO TRANSMITTER MODULE 1-GANG RF
17533 A 5072 RF TSM KNX RF radio transmitter module 2-gang PUSH BUTTONS

including transparent cover ref.-no.: A 50 NA
for cover kit 2-gang, complete, ref.-no.: A 502 TSA ..
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 2-gang push-button
2 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)

17533
A 5072 RF TSM KNX RF RADIO TRANSMITTER MODULE 2-GANG PUSH BUTTONS
17534 A 5073 RF TSM KNX RF Funk-Wandsender-Modul 3fach PUSH BUTTONS

including transparent cover ref.-no.: A 50 NA
for cover kit 3-gang, complete, ref.-no.: A 503 TSA ..
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 3-gang push-button
3 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
Transparent cover ref.-no.: A 50 NA

Accessories:
Neutral cover ref.-no.: A 50 NA W, A 50 NA WW, A 50 NA SW, A 50 NA AL, A 50 NA CH, A 50 NA MO

17534
A 5073 RF TSM KNX RF FUNK-WANDSENDER-MODUL 3FACH PUSH BUTTONS
17535 A 5074 RF TSM KNX RF radio transmitter module 4-gang PUSH BUTTONS

including transparent cover ref.-no.: A 50 NA
for cover kit 4-gang, complete, ref.-no.: A 504 TSA ..
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 4-gang push-button
4 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
Transparent cover ref.-no.: A 50 NA

Accessories:
Neutral cover ref.-no.: A 50 NA W, A 50 NA WW, A 50 NA SW, A 50 NA AL, A 50 NA CH, A 50 NA MO

17535
A 5074 RF TSM KNX RF RADIO TRANSMITTER MODULE 4-GANG PUSH BUTTONS
17536 CD 5071 RF TSM KNX RF radio transmitter module 1-gang RF

including transparent cover ref.-no.: CD 50 NA
for cover kit 1-gang, complete, ref.-no.: CD 501 TSA ..
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 1-gang push-button
1 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
transparent cover ref.-no.: CD 50 NA

Accessories:
Neutral cover ref.-no.: CD 50 NA W, CD 50 NA WW, CD 50 NA GR, CD 50 NA LG, CD 50 NA SW

17536
CD 5071 RF TSM KNX RF RADIO TRANSMITTER MODULE 1-GANG RF
17537 CD 5072 RF TSM KNX RF radio transmitter module 2-gang RF

or cover kit 2-gang, complete, ref.-no.: CD 502 TSA ..
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 2-gang push-button
2 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
transparent cover ref.-no.: CD 50 NA

Accessories:
Neutral cover ref.-no.: CD 50 NA W, CD 50 NA WW, CD 50 NA GR, CD 50 NA LG, CD 50 NA SW

17537
CD 5072 RF TSM KNX RF RADIO TRANSMITTER MODULE 2-GANG RF
17538 CD 5073 RF TSM KNX RF radio transmitter module 3-gang RF

including transparent cover ref.-no.: CD 50 NA
including transparent cover ref.-no.: CD 50 NA
for cover kit 3-gang, complete, ref.-no.: CD 503 TSA ..
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 3-gang push-button
3 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
transparent cover ref.-no.: CD 50 NA

Accessories:
Neutral cover ref.-no.: CD 50 NA W, CD 50 NA WW, CD 50 NA GR, CD 50 NA LG, CD 50 NA SW

17538
CD 5073 RF TSM KNX RF RADIO TRANSMITTER MODULE 3-GANG RF
17542 LS 5071 RF TSM KNX RF radio transmitter module 1-gang RF

including transparent cover ref.-no.: LS 50 NA
for cover kit 1-gang, complete, ref.-no.: ..501 TSA .. in the LS range
Can not be combined with frames in Flat Design.
Project design and commissioning with ETS5 or a more recent version.
ETS product family: Push-button
Product type: 1-gang push-button
1 green LED: actuator status
1 red LED: transmission status

Intended use
Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness values, calling up and saving light scenes
Operation in cabled KNX systems via radio converter (ref.-no.: MK 100 RF)
Mounting on appliance box according to DIN 49073, screw fixing on walls or adhesive fixing on smooth, even surfaces (glass)

Product characteristics
Push-button functions for switching, dimming, blinds control, valuators, light scenes, etc.
Button pairs for push-button function or rocker function
Status indication with LED
Integrated temperature sensor
Battery-powered device (battery compartment accessible from front)


Spare part:
transparent cover ref.-no.: LS 50 NA

Accessories:
Neutral cover ref.-no.: LS 50 NA W, LS 50 NA WW, LS 50 NA LG, LS 50 NA SW, AL 50 NA-L, ES 50 NA-L, AL 50 NA AN-L, ME 50 NA C-L, ME 50 NA AT-L, ME 50 NA D-L

17542
LS 5071 RF TSM KNX RF RADIO TRANSMITTER MODULE 1-GANG RF
17625 2225 WS U KNX universal weather station SENSORS

compact housing
including fastening arm
ETS product family: Input
Product type: Analogue input 4-gang

Intended use

Measurement and evaluation of weather data: wind speed, wind direction, precipitation, brightness, global radiation, twilight, temperature, relative air humidity and air pressure
Installation on the outside of buildings, preferable in the roof and facade area
Operation with additional power supply (ref.-no.: WSSV 10)

Product characteristics

Integrated GPS/GLONASS receiver for automated positioning
Calculation of additional weather data: absolute air humidity, chill temperature, comfort
Function for shading control
Integrated KNX bus coupling unit
Measuring and limit value monitoring
Software logic modules for linking events
Integrated heating

The weather station needs an operating voltage supply of 24 V AC, for example power supply module ref.-no. WSSV 10.

Spare part:
fastening arm ref.-no.: 2225 BFA

17625
2225 WS U KNX UNIVERSAL WEATHER STATION SENSORS
17826 SP K 10 FAPVD SW Display screen 10.1 inches. VISUALIZATION
KNX Smart pilot, 25.6 cm (10.1 inches), with black glass frame.

Rated voltage: AC 90 to 260 V ~, 50/60 Hz

For wall mounting, capacitive touch screen, without fan, without mechanical elements or moving parts,

Screen size: 223 x 125 mm (diagonal: 256 mm = 10.1 inches),

Format: 16: 9,

Resolution: WSVGA (1024 X 600), backlit LED Display

Reset switch,

Start, Languages in the disabled state incorporated,

Operating system: Windows Embedded Standard 2009, 2 preinstalled,

Software: Divus Phone video software for the integration of TKM equipment, pre-installed,

Built-in speaker, Built-in microphone,

Processor Model: Intel Atom N450, Industrial

CF 4 GB of memory and 2 GB of RAM,

4 USB ports: 2 in the rear and 2 in the state, 2 (separate)

LAN ports: built-in rear, 1000 Mbit / s,

Remote Maintenance: Via Internet / LAN
17826
SP K 10 FAPVD SW DISPLAY SCREEN 10.1 INCHES. VISUALIZATION
17921 SP 5.1 KNX Touch Panel 5.8 "TFT VISUALIZATION
KNX Smart Panel
With integrated 4: 3 bus coupler for wall mounting, touch screen
Fanless, without mechanically moving parts.
Product characteristics
Illuminated TFT graphic color monitor, 640 x 480 pixels, 16.7 million colors
Touch screen
Operating system Linux
Acoustic signal transmitter
KNX interface
Interfaces: Front accessible: 1 x USB
Interfaces: From rear accessible: Ethernet RJ45 (10/100 Mbit / s)
Programming via IP and USB stick
Predefined graphical user interface
Free graphical user interface
Combination of predefined and free user interface
Master pages: max. 10
Free pages: max. 50
Elements: max. 400
Copy & paste features
Remote functionality
Quick access to pages and functions
17921
SP 5.1 KNX TOUCH PANEL 5.8 "TFT VISUALIZATION
18365 SC 10 VISUALIZATION

Smart Control 10.1’’

aspect ratio 16:9
for installation in walls, capacitive touch screen
fanless, without rotating parts

  • Door call function only in combination with Siedle Smart Gateway SG 650-..
  • KNX visualisation in combination with Facility Pilot Server (ref.-no.: FAPV SERVER REG GB)
  • KNX visualisation in combination with Smart Visu Server (ref.-no.: SV-SERVER-INT)
  • Pre-installed iHaus-Server-App; iHaus-KNX connection exclusively via IP router (ref.-no.: IPR 200 REG) or IP interface (ref.-no.: IPS 200 REG)
  • eNet visualisation in combination with eNet server for rail mounting (ref.-no.: ENET-SERVER)
  • eNet visualisation in combination with eNet radio IP gateway IP (ref.-no.: FM-GATE-IP)
  • Pre-installed weather page
Update firmware prior to commissioning.
Please check Release Notes.

Accessories:
Flush-mounted recessed box ref.-no.: SC 10 EBG
Power supply ref.-no.: NT 2415 REG VDC
REDUCE INFO

VersionReference numberInformation 
25.6 cm – 10.1’’SC 10
INFO
*Price on request
Technical data
Screen size (W x H):223 x 125 mm
Screen diagonal:256 mm / 10.1’’
Resolution:WSVGA (1024 x 600), LED backlight display
Frame dimensions (W x H):333 x 200 mm
Power consumption:max. 15 W
Power supply:PoE+ acc. to IEEE 802.3at, with Cat5e/Cat6 cable, length max. 100 m or
DC 12 ... 32 V via external power supply (ref.-no. NT 2415 REG VDC, not included)
Operating system:Android 4.2
Processor:Cortex-A9
Main memory:2 GB
Mass storage:8 GB Flash (available disc space depends on operating system)
Slot of memory card:microSD
Loudspeaker:integrated
Microphone:integrated
USB ports:2 x USB 2.0
1 x Mini-USB OTG (accessible from the front)
LAN connections:1 x 10/100 Mbit/s
Ambient temperature:0 ... +30 °C
18365
SC 10 VISUALIZATION
3554 LSP 985 ES FRAME STAINLESS STEEL, SERIE LS PLUS SIN FAMILIA
Frames for horizontal and vertical installation Stainless Steel 5-gang 115 x 399 mm
3554
LSP 985 ES FRAME STAINLESS STEEL, SERIE LS PLUS SIN FAMILIA
2472 28 G Locking (profile cylinder) for key switch/push-button inserts with equal keys. (DIN 18 252) SIN FAMILIA
Locking (profile cylinder) for key switch/push-button inserts with equal keys
2472
28 G LOCKING (PROFILE CYLINDER) FOR KEY SWITCH/PUSH-BUTTON INSERTS WITH EQUAL KEYS. (DIN 18 252) SIN FAMILIA
2498 PM-Kappe Surface cap DETECTORS
Surface cap Presence detector whait alpine
2498
PM-KAPPE SURFACE CAP DETECTORS
2501 FUS 4410 WW Magnet contact, white ALARMS CENTRAL
KNX Alarm system Magnet contact Der Magnetkontakt ist staub- und wassergeschuetzt in ein Glasroehrchen eingeschmolzen (Reedkontakt). Ein Reedkontakt wird beruehrungslos durch einen Permanentmagneten betaetigt. Beim Einbau in Stahlprofile (magnetischer Werkstoff) koennen nur Blockreedkontakte verwendet werden. Lieferumfang: 2 Aufbaugehaeuse, 2 Kappen, 3 Unterlegteile 2 mm 1 Unterlegteil 6 mm Anschluss an EAM 4000: ueber Binaereingang 6fach, z.B. Art.-Nr.: 2126 REG, bzw. Tasterschnittstelle, z.B. Art.-Nr.: 2076-2 T bzw. 2076-4 T, mind. 2-adrig, z.B. J-Y(St)Y 2x2x0,8 Colour: brown Version: (similar RAL 8022) ava_fabrikat ava_artnr FUS 4410 BR
2501
FUS 4410 WW MAGNET CONTACT, WHITE ALARMS CENTRAL
2544 A 569 PLT Center plate for USB data interface SYSTEM DEVICES
The USB data interface enables the coupling of a PC for the addressing, programming and diagnoses of KNX components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the KNX if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future standards.
2544
A 569 PLT CENTER PLATE FOR USB DATA INTERFACE SYSTEM DEVICES
2636 569 T Centre plate for USB data interface ref.-no.: 2130 USB SYSTEM DEVICES
Centre plate for USB data interface ref.-no.: 2130 USB for Rutenbeck: UM-MA 2 Up with UM-real Cat.6a A for Dätwyler: flush-mounted modular jack socket (for 2 x MS-K 1/8 Cat.6a), ref.-no.: 440 012
2636
569 T CENTRE PLATE FOR USB DATA INTERFACE REF.-NO.: 2130 USB SYSTEM DEVICES
2646 569 TNA Centre plate with inscription field 6 x 37 mm for USB data interface ref.-no.: 2130 USB SYSTEM DEVICES
for USB data interface ref.-no.: 2130 USB for Rutenbeck: UM-MA 2 Up with UM-real Cat.6a A for Dätwyler: flush-mounted modular jack socket (for 2 x MS-K 1/8 Cat.6a), ref.-no.: 440 012
2646
569 TNA CENTRE PLATE WITH INSCRIPTION FIELD 6 X 37 MM FOR USB DATA INTERFACE REF.-NO.: 2130 USB SYSTEM DEVICES
2727 LS 969 T Center plate for USB data interface, Ls 990, Ls plus , white SYSTEM DEVICES
KNX USB data-interface 2130 USB ETS-product family: Communication LS 990 / LS plus / Aluminium / Stainless Steel / Anthracite / Chrom / Gold The USB data interface enables the coupling of a PC for the addressing, programming and diagnoses of KNX components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the KNX if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future
2727
LS 969 T CENTER PLATE FOR USB DATA INTERFACE, LS 990, LS PLUS , WHITE SYSTEM DEVICES
2733 AL 2969 T NA Center plate for USB data interface, desing Ls 990, Ls plus, aluminium SYSTEM DEVICES
KNX USB data-interface 2130 USB ETS-product family: Communication CD 500 / CD plus with inscription plate The USB data interface enables the coupling of a PC for the addressing, programming and diagnoses of KNX components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the KNX if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future standards.
2733
AL 2969 T NA CENTER PLATE FOR USB DATA INTERFACE, DESING LS 990, LS PLUS, ALUMINIUM SYSTEM DEVICES
2811 WS 10 H BRIGHTNESS SENSOR WS 10 H SENSORS
Brightness sensor WS 10 H (No KNX device) The brightness sensor is used for the measuring and evaluation of the brightness. The brightness measured by a photodiode is transmitted to an analog output signal of 0 V – 10 V by the electronics. Technical data Range: 0 ... 60.000 Lux, linear Electrical output: 0 V ... 10 V, short-circuit / proof Protection: IP 65 Plasting housing with PG7 thread + screw and pressure respectively moisture compensation (recommended cable 3 x 0.25 mm2)
2811
WS 10 H BRIGHTNESS SENSOR WS 10 H SENSORS
2813 WS 10 T TEMPERATURE SENSOR WS 10 T SENSORS
Temperature sensor WS 10 T (No KNX device) The temperature sensor is used for the measuring and evaluation of the temperature. The temperature measured by a temperature sensor is transmitted to an analog output signal of 0 V 10 V by the electronics. Technical data Range: 30 C ... +70 C, linear Electrical output: 0 V ... 10 V, short-circuit / proof Protection: IP 65 Plasting housing with PG7 thread + screw and pressure respectively moisture compensation (recommended cable 3 x 0.25 mm2)
2813
WS 10 T TEMPERATURE SENSOR WS 10 T SENSORS
2830 2050 K Connection cover KNX ACCESSORIES
Connection cover For REG components ETS product family: System accessories
2830
2050 K CONNECTION COVER KNX ACCESSORIES
2849 EBG 24 FLUSH MOUNTED RECESSED BOX EBG 24 VISUALIZATION
Flush mounted recessed box EBG 24 212 x 124 x 75 mm (W x H x D) Fits for MT 701 and FP 701 CT IP.
2849
EBG 24 FLUSH MOUNTED RECESSED BOX EBG 24 VISUALIZATION
2874 CD 590 Rocker 1-gang, switch position, pusch buttons, white PUSH BUTTONS
KNX Push button BCU 1-gang rocker for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: CD 590
2874
CD 590 ROCKER 1-GANG, SWITCH POSITION, PUSCH BUTTONS, WHITE PUSH BUTTONS
2883 CD 590 P 1-gang rocker with symbols for 1-gang push-button BCU , cd 500, cd plus PUSH BUTTONS
KNX Push button BCU 1-gang rocker with symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: CD 590 P
2883
CD 590 P 1-GANG ROCKER WITH SYMBOLS FOR 1-GANG PUSH-BUTTON BCU , CD 500, CD PLUS PUSH BUTTONS
2892 CD 590 NA 1-gang rocker with inscription plate Ivory for 1-gang push-button BCU white desing cd 500 cd plus PUSH BUTTONS
KNX Push button BCU 1-gang rocker with inscription field 9 x 58 mm for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Beschriftungsbogen, weiß 1 Bogen = 26 Nutzen 9 x 58 mm: Art.-Nr. BB 3.1 Beschriftungsbogen für Metallausführungen weiß, 1 Bogen = 34 Nutzen 7 x 57 mm: Art.-Nr. BB 3 For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: CD 590 NA
2892
CD 590 NA 1-GANG ROCKER WITH INSCRIPTION PLATE IVORY FOR 1-GANG PUSH-BUTTON BCU WHITE DESING CD 500 CD PLUS PUSH BUTTONS
2896 CD 590 NA GR 1-gang rocker with inscription plate , grey desing cd 500 cd plus PUSH BUTTONS
KNX Push button BCU 1-gang rocker with inscription field 9 x 58 mm for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Beschriftungsbogen, weiß 1 Bogen = 26 Nutzen 9 x 58 mm: Art.-Nr. BB 3.1 Beschriftungsbogen für Metallausführungen weiß, 1 Bogen = 34 Nutzen 7 x 57 mm: Art.-Nr. BB 3 For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: grey Manufacturer: JUNG Ref.-no.: CD 590 NA GR
2896
CD 590 NA GR 1-GANG ROCKER WITH INSCRIPTION PLATE , GREY DESING CD 500 CD PLUS PUSH BUTTONS
2897 CD 590 NA LG 1-gang rocker with inscription plate, ligth grey desing cd 500 cd plus PUSH BUTTONS
KNX Push button BCU 1-gang rocker with inscription field 9 x 58 mm for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Beschriftungsbogen, weiß 1 Bogen = 26 Nutzen 9 x 58 mm: Art.-Nr. BB 3.1 Beschriftungsbogen für Metallausführungen weiß, 1 Bogen = 34 Nutzen 7 x 57 mm: Art.-Nr. BB 3 For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: light grey Manufacturer: JUNG Ref.-no.: CD 590 NA LG
2897
CD 590 NA LG 1-GANG ROCKER WITH INSCRIPTION PLATE, LIGTH GREY DESING CD 500 CD PLUS PUSH BUTTONS
2910 CD 590 KO5P Push button BCU 1-gang rocker with lens and symbols ivory PUSH BUTTONS
KNX Push button BCU 1-gang rocker with lens and symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: CD 590 KO5P
2910
CD 590 KO5P PUSH BUTTON BCU 1-GANG ROCKER WITH LENS AND SYMBOLS IVORY PUSH BUTTONS
2919 CD 590 NAKO5 KNX Push button BCU 1-gang rocker with lens and inscription field 9 x 58 mm ivory SIN FAMILIA
KNX Push button BCU 1-gang rocker with lens and inscription field 9 x 58 mm illumination possible for switch insert with indicator light ref.-no.: 506 KOU, 502 KOU, 503 KOU for push switch insert with indicator light ref.-no.: 506 KOTU, 502 KOTU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U, 534 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Beschriftungsbogen, weiß 1 Bogen = 26 Nutzen 9 x 58 mm: Art.-Nr. BB 3.1 Beschriftungsbogen für Metallausführungen weiß, 1 Bogen = 34 Nutzen 7 x 57 mm: Art.-Nr. BB 3 Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: CD 590 NAKO5
2919
CD 590 NAKO5 KNX PUSH BUTTON BCU 1-GANG ROCKER WITH LENS AND INSCRIPTION FIELD 9 X 58 MM IVORY SIN FAMILIA
2926 A 590 WW KNX Push button BCU 1-gang rocker white alpine SIN FAMILIA
KNX Push button BCU 1-gang rocker

for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U
for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU
for push-button insert ref.-no.: 531 U, 533 U, 533-2 U
for 1-gang push-button BCU
neutral position ref.-no.: 2071.02 LED
switch position ref.-no.: 2071.01 LED

For rockers to be illuminated use ref.-no. ..KO..

Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range.

Colour: white

Manufacturer: JUNG
Ref.-no.: A 590 WW

2926
A 590 WW KNX PUSH BUTTON BCU 1-GANG ROCKER WHITE ALPINE SIN FAMILIA
2928 A 590 P WW KNX Push button BCU 1-gang rocker with symbols white alpine PUSH BUTTONS
KNX Push button BCU 1-gang rocker with symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: white Manufacturer: JUNG Ref.-no.: A 590 P WW
2928
A 590 P WW KNX PUSH BUTTON BCU 1-GANG ROCKER WITH SYMBOLS WHITE ALPINE PUSH BUTTONS
2929 A 590 P AL KNX Push button BCU 1-gang rocker with symbols aluminium SIN FAMILIA
KNX Push button BCU 1-gang rocker with symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: aluminium Manufacturer: JUNG Ref.-no.: A 590 P AL
2929
A 590 P AL KNX PUSH BUTTON BCU 1-GANG ROCKER WITH SYMBOLS ALUMINIUM SIN FAMILIA
2930 A 590 KO5 WW KNX Push button BCU 1-gang rocker with lens white alpine SIN FAMILIA
KNX Push button BCU 1-gang rocker with lens

illumination possible
for switch insert with indicator light ref.-no.: 506 KOU, 502 KOU, 503 KOU
for push switch insert with indicator light ref.-no.: 506 KOTU, 502 KOTU
for push-button insert ref.-no.: 531 U, 533 U, 533-2 U, 534 U
for 1-gang push-button BCU
neutral position ref.-no.: 2071.02 LED
switch position ref.-no.: 2071.01 LED

Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range.

Colour: white

Manufacturer: JUNG
Ref.-no.: A 590 KO5 WW

2930
A 590 KO5 WW KNX PUSH BUTTON BCU 1-GANG ROCKER WITH LENS WHITE ALPINE SIN FAMILIA
2931 A 590 KO5 AL KNX Push button BCU 1-gang rocker with lens aluminium SIN FAMILIA
KNX Push button BCU 1-gang rocker with lens illumination possible for switch insert with indicator light ref.-no.: 506 KOU, 502 KOU, 503 KOU for push switch insert with indicator light ref.-no.: 506 KOTU, 502 KOTU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U, 534 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: aluminium Manufacturer: JUNG Ref.-no.: A 590 KO5 AL
2931
A 590 KO5 AL KNX PUSH BUTTON BCU 1-GANG ROCKER WITH LENS ALUMINIUM SIN FAMILIA
2932 AS 590 AS 500AS 500 1-gang rocker, full plate white SIN FAMILIA
AS 500AS 500 1-gang rocker, full plate for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU. Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590
2932
AS 590 AS 500AS 500 1-GANG ROCKER, FULL PLATE WHITE SIN FAMILIA
2933 AS 591 AS 500 1-gang rocker white PUSH BUTTONS
AS 500 1-gang rocker for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591
2933
AS 591 AS 500 1-GANG ROCKER WHITE PUSH BUTTONS
2936 A 590 KO5P WW 1-gang rocker with lens and symbols SIN FAMILIA
1-gang rocker with transparent lens and symbols (A 500, A plus) for 1-gang push-button BCU
2936
A 590 KO5P WW 1-GANG ROCKER WITH LENS AND SYMBOLS SIN FAMILIA
2937 A 590 KO5P AL 1-GANG ROCKER SIN FAMILIA
1-gang rocker with transparent lens and symbols (A 500, A plus) for 1-gang push-button BCU
2937
A 590 KO5P AL 1-GANG ROCKER SIN FAMILIA
2938 AS 590 P KNX Taster BA 1-gang rocker with symbols, full plate , white PUSH BUTTONS
KNX Taster BA 1-gang rocker with symbols, full plate for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590 P
2938
AS 590 P KNX TASTER BA 1-GANG ROCKER WITH SYMBOLS, FULL PLATE , WHITE PUSH BUTTONS
2939 AS 591 P 1-GANG ROCKER WITH SYMBOLS (AS 500) white PUSH BUTTONS
KNX Push button BCU 1-gang rocker with symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: white Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591 P WW
2939
AS 591 P 1-GANG ROCKER WITH SYMBOLS (AS 500) WHITE PUSH BUTTONS
2942 AS 590 KO5 KNX Push button BCU 1-gang rocker with lens white PUSH BUTTONS
KNX Push button BCU 1-gang rocker with lens, full plate illumination possible for switch insert with indicator light ref.-no.: 506 KOU, 502 KOU, 503 KOU for push switch insert with indicator light ref.-no.: 506 KOTU, 502 KOTU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U, 534 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU. Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590 KO5
2942
AS 590 KO5 KNX PUSH BUTTON BCU 1-GANG ROCKER WITH LENS WHITE PUSH BUTTONS
2943 AS 591 KO5 1-GANG ROCKER WITH TRANSPARENT LENS (AS 500) ivory PUSH BUTTONS
KNX Push button BCU 1-gang rocker with lens illumination possible for switch insert with indicator light ref.-no.: 506 KOU, 502 KOU, 503 KOU for push switch insert with indicator light ref.-no.: 506 KOTU, 502 KOTU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U, 534 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591 KO5
2943
AS 591 KO5 1-GANG ROCKER WITH TRANSPARENT LENS (AS 500) IVORY PUSH BUTTONS
2946 SL 590 WW 1-GANG ROCKER sl 500 white alpine PUSH BUTTONS
SL 500 1-gang rocker for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU switch position ref.-no.: 2071.01 LED Colour: white Manufacturer: JUNG Ref.-no.: SL 590 WW
2946
SL 590 WW 1-GANG ROCKER SL 500 WHITE ALPINE PUSH BUTTONS
2952 AS 590 KO5P KNX Taster Ba 1-gang rocker with lens and symbols, full plate WHITE PUSH BUTTONS
KNX Taster Ba 1-gang rocker with lens and symbols, full plate for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590 KO5P
2952
AS 590 KO5P KNX TASTER BA 1-GANG ROCKER WITH LENS AND SYMBOLS, FULL PLATE WHITE PUSH BUTTONS
2953 AS 591 KO5P 1-GANG ROCKER WITH TRANSPARENT LENS AND SYMBOLS WHITE PUSH BUTTONS
KNX Push button BCU 1-gang rocker with lens and symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591 KO5P
2953
AS 591 KO5P 1-GANG ROCKER WITH TRANSPARENT LENS AND SYMBOLS WHITE PUSH BUTTONS
2957 LS 990 1-GANG ROCKER WHITE LS 990 SIN FAMILIA
LS 990 1-gang rocker for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: LS 990
2957
LS 990 1-GANG ROCKER WHITE LS 990 SIN FAMILIA
2963 LS 990 P 1-gang rocker with symbols, WHITE, LS 990 SIN FAMILIA
KNX Push button BCU 1-gang rocker with symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: LS 990 P
2963
LS 990 P 1-GANG ROCKER WITH SYMBOLS, WHITE, LS 990 SIN FAMILIA
2964 LS 990 P WW 1-gang rocker with symbols WHITE ALPINE SIN FAMILIA
KNX Push button BCU 1-gang rocker with symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: white Manufacturer: JUNG Ref.-no.: LS 990 P WW
2964
LS 990 P WW 1-GANG ROCKER WITH SYMBOLS WHITE ALPINE SIN FAMILIA
2969 LS 990 NA LS 990 1-gang rocker with inscription field 9 x 58 mm SIN FAMILIA
LS 990 1-gang rocker with inscription field 9 x 58 mm for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Beschriftungsbogen, weiß 1 Bogen = 26 Nutzen 9 x 58 mm: Art.-Nr. BB 3.1 For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: LS 990 NA
2969
LS 990 NA LS 990 1-GANG ROCKER WITH INSCRIPTION FIELD 9 X 58 MM SIN FAMILIA
2973 AL 2990 NA LS 990 1-gang rocker with inscription field 12 x 55 mm, ALUMINIUM SIN FAMILIA
Aluminium 1-gang rocker with inscription field 12 x 55 mm for switch insert ref.-no.: 506 U, 507 U, 502 U, 503 U for push switch insert ref.-no.: 506 TU, 507 TU, 502 TU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Version: aluminium Manufacturer: JUNG Ref.-no.: AL 2990 NA
2973
AL 2990 NA LS 990 1-GANG ROCKER WITH INSCRIPTION FIELD 12 X 55 MM, ALUMINIUM SIN FAMILIA
2975 LS 990 KO5 LS 990, 1-gang rocker with lens, WHITE SIN FAMILIA
LS 990 1-gang rocker with lens illumination possible for switch insert with indicator light ref.-no.: 506 KOU, 502 KOU, 503 KOU for push switch insert with indicator light ref.-no.: 506 KOTU, 502 KOTU for push-button insert ref.-no.: 531 U, 533 U, 533-2 U, 534 U for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED switch position ref.-no.: 2071.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: LS 990 KO5
2975
LS 990 KO5 LS 990, 1-GANG ROCKER WITH LENS, WHITE SIN FAMILIA
2981 LS 990 KO5P 1-gang rocker with lens and symbols, KNX Push button BCU . white SIN FAMILIA
KNX Push button BCU 1-gang rocker with lens and symbols for 1-gang push-button BCU neutral position ref.-no.: 2071.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: LS 990 KO5P
2981
LS 990 KO5P 1-GANG ROCKER WITH LENS AND SYMBOLS, KNX PUSH BUTTON BCU . WHITE SIN FAMILIA
2984 LS 990 KO5P SW WIPPE FÜR TASTER BA SIN FAMILIA
Wippe mit Lichtleiter und Symbolen für Taster BA 1fach Mittenstellung Art.-Nr.: 2071.02 LED Farbe:SCHWARZ
2984
LS 990 KO5P SW WIPPE FÜR TASTER BA SIN FAMILIA
2987 CD 595 KO5MP KNX Push button BCU 2-gang rocker with lens and symbols ls 990, white PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: CD 595 KO5MP
2987
CD 595 KO5MP KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS LS 990, WHITE PUSH BUTTONS
2988 CD 595 KO5P KNX Push button BCU 2-gang rocker with lens and symbols, white , ls 990 SIN FAMILIA
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: ivory Manufacturer: JUNG Ref.-no.: CD 595 KO5P
2988
CD 595 KO5P KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS, WHITE , LS 990 SIN FAMILIA
3015 CD 595 2-gang rocker cd 500, ivory PUSH BUTTONS
CD 500 2-gang rocker for switch insert ref.-no.: 505 U, 509 U for push switch insert ref.-no.: 505 TU, 509 TU for push-button insert ref.-no.: 535 U, 539 U for multi switch insert ref.-no.: 532-4 U for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: CD 595
3015
CD 595 2-GANG ROCKER CD 500, IVORY PUSH BUTTONS
3024 CD 595 MP KNX Push button BCU 2-gang rocker with symbols, white PUSH BUTTONS
KNX Push button BCU 2-gang rocker with symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: CD 595 MP
3024
CD 595 MP KNX PUSH BUTTON BCU 2-GANG ROCKER WITH SYMBOLS, WHITE PUSH BUTTONS
3033 CD 595 P cd 500, 2-gang rocker with symbols white PUSH BUTTONS
CD 500 2-gang rocker with symbols for blind switch insert ref.-no.: 509 VU for blind push-button insert ref.-no.: 539 VU for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: CD 595 P
3033
CD 595 P CD 500, 2-GANG ROCKER WITH SYMBOLS WHITE PUSH BUTTONS
3042 CD 595 KO5 2-GANG ROCKER WITH 2 TRANSPARENT LENSES, cd 500, white PUSH BUTTONS
CD 500 2-gang rocker with lens illumination possible for switch insert ref.-no.: 505 U 5 for switch insert with indicator light ref.-no.: 505 KOU 5 for push-button insert ref.-no.: 535 U 5 for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: CD 595 KO5
3042
CD 595 KO5 2-GANG ROCKER WITH 2 TRANSPARENT LENSES, CD 500, WHITE PUSH BUTTONS
3067 AS 590-5 KNX Push button BCU 2-gang rocker, full plate whte PUSH BUTTONS
KNX Push button BCU 2-gang rocker, full plate for switch insert ref.-no.: 505 U, 509 U for push switch insert ref.-no.: 505 TU, 509 TU for push-button insert ref.-no.: 535 U, 539 U for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU. Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590-5
3067
AS 590-5 KNX PUSH BUTTON BCU 2-GANG ROCKER, FULL PLATE WHTE PUSH BUTTONS
3068 AS 591-5 KNX Push button BCU 2-gang rocker, PUSH BUTTONS
KNX Push button BCU 2-gang rocker for switch insert ref.-no.: 505 U, 509 U for push switch insert ref.-no.: 505 TU, 509 TU for push-button insert ref.-no.: 535 U, 539 U for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591-5
3068
AS 591-5 KNX PUSH BUTTON BCU 2-GANG ROCKER, PUSH BUTTONS
3071 AS 590-5 MP KNX Push button BCU 2-gang rocker with symbols, full plate , ivory PUSH BUTTONS
KNX Push button BCU 2-gang rocker with symbols, full plate for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590-5 MP
3071
AS 590-5 MP KNX PUSH BUTTON BCU 2-GANG ROCKER WITH SYMBOLS, FULL PLATE , IVORY PUSH BUTTONS
3072 AS 591-5 MP 2-gang rocker with symbols, ivory PUSH BUTTONS
KNX Push button BCU 2-gang rocker with symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591-5 MP
3072
AS 591-5 MP 2-GANG ROCKER WITH SYMBOLS, IVORY PUSH BUTTONS
3075 AS 590-5 P AS 500 2-gang rocker with symbols, full plate, white PUSH BUTTONS
AS 500 2-gang rocker with symbols, full plate for blind switch insert ref.-no.: 509 VU for blind push-button insert ref.-no.: 539 VU for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU. Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590-5 P
3075
AS 590-5 P AS 500 2-GANG ROCKER WITH SYMBOLS, FULL PLATE, WHITE PUSH BUTTONS
3076 AS 591-5 P AS 500 2-gang rocker with symbols, white PUSH BUTTONS
AS 500 2-gang rocker with symbols for blind switch insert ref.-no.: 509 VU for blind push-button insert ref.-no.: 539 VU for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591-5 P
3076
AS 591-5 P AS 500 2-GANG ROCKER WITH SYMBOLS, WHITE PUSH BUTTONS
3079 AS 590-5 KO5 2-gang rocker with lens, full plate, whitem, as 500 PUSH BUTTONS
AS 500 2-gang rocker with lens, full plate illumination possible for switch insert ref.-no.: 505 U 5 for switch insert with indicator light ref.-no.: 505 KOU 5 for push-button insert ref.-no.: 535 U 5 for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU. Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590-5 KO5
3079
AS 590-5 KO5 2-GANG ROCKER WITH LENS, FULL PLATE, WHITEM, AS 500 PUSH BUTTONS
3080 AS 591-5 KO5 AS 500 2-gang rocker with lens, white PUSH BUTTONS
AS 500 2-gang rocker with lens illumination possible for switch insert ref.-no.: 505 U 5 for switch insert with indicator light ref.-no.: 505 KOU 5 for push-button insert ref.-no.: 535 U 5 for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591-5 KO5
3080
AS 591-5 KO5 AS 500 2-GANG ROCKER WITH LENS, WHITE PUSH BUTTONS
3083 AS 590-5 KO5MP KNX Push button BCU 2-gang rocker with lens and symbols, full plate, white PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols, full plate for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590-5 KO5MP
3083
AS 590-5 KO5MP KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS, FULL PLATE, WHITE PUSH BUTTONS
3084 AS 591-5 KO5MP KNX Push button BCU 2-gang rocker with lens and symbols , white PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591-5 KO5MP
3084
AS 591-5 KO5MP KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS , WHITE PUSH BUTTONS
3087 AS 590-5 KO5P KNX Push button BCU 2-gang rocker with lens and symbols, full plate , white PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols, full plate for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: ivory Version: full plate Manufacturer: JUNG Ref.-no.: AS 590-5 KO5P
3087
AS 590-5 KO5P KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS, FULL PLATE , WHITE PUSH BUTTONS
3088 AS 591-5 KO5P KNX Push button BCU 2-gang rocker with lens and symbols, PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: ivory Version: centre plate Manufacturer: JUNG Ref.-no.: AS 591-5 KO5P
3088
AS 591-5 KO5P KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS, PUSH BUTTONS
3091 A 595 WW 2-GANG ROCKER (A 500, A PLUS) FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
A 500 2-gang rocker for switch insert ref.-no.: 505 U, 509 U for push switch insert ref.-no.: 505 TU, 509 TU for push-button insert ref.-no.: 535 U, 539 U for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: white Manufacturer: JUNG Ref.-no.: A 595 WW
3091
A 595 WW 2-GANG ROCKER (A 500, A PLUS) FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
3093 A 595 MP WW 2-GANG ROCKER WITH SYMBOLS (A 500, A PLUS) FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
KNX Push button BCU 2-gang rocker with symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: white Manufacturer: JUNG Ref.-no.: A 595 MP WW
3093
A 595 MP WW 2-GANG ROCKER WITH SYMBOLS (A 500, A PLUS) FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
3095 A 595 P WW 2-GANG ROCKER WITH SYMBOLS PUSH BUTTONS
A 500 2-gang rocker with symbols for blind switch insert ref.-no.: 509 VU for blind push-button insert ref.-no.: 539 VU for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: white Manufacturer: JUNG Ref.-no.: A 595 P WW
3095
A 595 P WW 2-GANG ROCKER WITH SYMBOLS PUSH BUTTONS
3097 A 595 KO5 WW 2-GANG ROCKER WITH TRANSPARENT LENS FOR 2-GANG SWITCH INSERT WITH INDICATOR LIGHT PILOT PUSH BUTTONS
A 500 2-gang rocker with lens illumination possible for switch insert ref.-no.: 505 U 5 for switch insert with indicator light ref.-no.: 505 KOU 5 for push-button insert ref.-no.: 535 U 5 for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: white Manufacturer: JUNG Ref.-no.: A 595 KO5 WW
3097
A 595 KO5 WW 2-GANG ROCKER WITH TRANSPARENT LENS FOR 2-GANG SWITCH INSERT WITH INDICATOR LIGHT PILOT PUSH BUTTONS
3099 A 595 KO5MP WW KNX Push button BCU 2-gang rocker with lens and symbols PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: white Manufacturer: JUNG Ref.-no.: A 595 KO5MP WW
3099
A 595 KO5MP WW KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS PUSH BUTTONS
3101 A 595 KO5P WW WIPPE MIT LICHTLEITER UND SYMBOLEN FÜR TASTER BA 2FACH KNX Push button BCU 2-gang rocker with lens and symbols white PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: white Manufacturer: JUNG Ref.-no.: A 595 KO5P WW
3101
A 595 KO5P WW WIPPE MIT LICHTLEITER UND SYMBOLEN FÜR TASTER BA 2FACH KNX PUSH BUTTON BCU 2-GANG ROCKER WITH LENS AND SYMBOLS WHITE PUSH BUTTONS
3103 SL 595 WW 2-GANG ROCKER FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
SL 500 2-gang rocker for switch insert ref.-no.: 505 U, 509 U for push switch insert ref.-no.: 505 TU, 509 TU for push-button insert ref.-no.: 535 U, 539 U for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: white Manufacturer: JUNG Ref.-no.: SL 595 WW
3103
SL 595 WW 2-GANG ROCKER FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
3106 SL 595 P WW 2-GANG ROCKER WITH SYMBOLSM FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
SL 500 2-gang rocker with symbols for blind switch insert ref.-no.: 509 VU for blind push-button insert ref.-no.: 539 VU for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: white Manufacturer: JUNG Ref.-no.: SL 595 P WW
3106
SL 595 P WW 2-GANG ROCKER WITH SYMBOLSM FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
3109 SL 595 KO5 WW 2-GANG ROCKER WITH TRANSPARENT LENS.FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
SL 500 2-gang rocker with lens for switch insert ref.-no.: 505 U 5 for switch insert with indicator light ref.-no.: 505 KOU 5 for push-button insert ref.-no.: 535 U 5 for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: white Manufacturer: JUNG Ref.-no.: SL 595 KO5 WW
3109
SL 595 KO5 WW 2-GANG ROCKER WITH TRANSPARENT LENS.FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
3112 SL 595 KO5P WW 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: white Manufacturer: JUNG Ref.-no.: SL 595 KO5P WW
3112
SL 595 KO5P WW 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU PUSH BUTTONS
3115 LS 995 2-GANG ROCKER LS 990, IVORY SIN FAMILIA
LS 990 2-gang rocker for switch insert ref.-no.: 505 U, 509 U for push switch insert ref.-no.: 505 TU, 509 TU for push-button insert ref.-no.: 535 U, 539 U for multi switch insert ref.-no.: 532-4 U (not metal versions) for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED For rockers to be illuminated use ref.-no. ..KO.. Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: LS 995
3115
LS 995 2-GANG ROCKER LS 990, IVORY SIN FAMILIA
3121 LS 995 MP 2-GANG ROCKER WITH SYMBOLS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Push button BCU 2-gang rocker with symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: LS 995 MP
3121
LS 995 MP 2-GANG ROCKER WITH SYMBOLS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
3126 LS 995 P 2-GANG ROCKER WITH SYMBOLS FOR 2-GANG PUSH-BUTTON BCU , WHITE SIN FAMILIA
LS 990 2-gang rocker with symbols for blind switch insert ref.-no.: 509 VU for blind push-button insert ref.-no.: 539 VU for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: white Manufacturer: JUNG Ref.-no.: LS 995 P WW
3126
LS 995 P 2-GANG ROCKER WITH SYMBOLS FOR 2-GANG PUSH-BUTTON BCU , WHITE SIN FAMILIA
3129 LS 995 P SW 2-GANG ROCKER WITH SYMBOLS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Taster BA Wippe mit Symbolen für Jalousie-Schalter Art.-Nr.: 509 VU für Jalousie-Taster Art.-Nr.: 539 VU für Taster BA 2fach Tasterstellung Art.-Nr.: 2072.01 LED Mit Dichtungsflansch Art.-Nr.: 551 WU und programmspezifischen "IP 44-Rahmen" ist der Schutzgrad IP 44 gewährleistet. Farbe: SCHARZ
3129
LS 995 P SW 2-GANG ROCKER WITH SYMBOLS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
3132 LS 995 KO5 2-GANG ROCKER WITH TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU, IVORY SIN FAMILIA
LS 990 2-gang rocker with lens illumination possible for switch insert ref.-no.: 505 U 5 for switch insert with indicator light ref.-no.: 505 KOU 5 for push-button insert ref.-no.: 535 U 5 for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED switch position ref.-no.: 2072.01 LED Protection level IP 44 is ensured with sealing gasket ref.-no. 551 WU and "IP 44 frame" of the respective design range. Colour: ivory Manufacturer: JUNG Ref.-no.: LS 995 KO5
3132
LS 995 KO5 2-GANG ROCKER WITH TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU, IVORY SIN FAMILIA
3135 LS 995 KO5 SW 2-GANG ROCKER WITH TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Taster BA Wippe mit Lichtleiter für Serienschalter Art.-Nr.: 505 U 5 für Serien-Wipp-Kontrollschalter Art.-Nr.: 505 KOU 5 für Doppel-Taster Art.-Nr.: 535 U 5 für Taster BA 2fach Mittenstellung Art.-Nr.: 2072.02 LED Tasterstellung Art.-Nr.: 2072.01 LED Mit Dichtungsflansch Art.-Nr.: 551 WU und programmspezifischen "IP 44-Rahmen" ist der Schutzgrad IP 44 gewährleistet. Farbe: schwarz
3135
LS 995 KO5 SW 2-GANG ROCKER WITH TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
3138 LS 995 KO5MP 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG IVORY PUSH-BUTTON BCU SIN FAMILIA
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU neutral position ref.-no.: 2072.02 LED Colour: ivory Manufacturer: JUNG Ref.-no.: LS 995 KO5MP
3138
LS 995 KO5MP 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG IVORY PUSH-BUTTON BCU SIN FAMILIA
3141 LS 995 KO5MP SW 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Taster BA Wippe mit Lichtleiter und Symbolen für Taster BA 2fach Mittenstellung Art.-Nr.: 2072.02 LED Farbe: lichtgrau (ähnlich RAL 7035) Fabrikat : Jung Art.-Nr.: LS 995 KO5MP LG
3141
LS 995 KO5MP SW 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
3144 LS 995 KO5P 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Push button BCU 2-gang rocker with lens and symbols for 2-gang push-button BCU switch position ref.-no.: 2072.01 LED Colour: ivory Manufacturer: JUNG Ref.-no.: LS 995 KO5P
3144
LS 995 KO5P 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
3147 LS 995 KO5P SW 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Taster BA Wippe mit Lichtleiter und Symbolen für Taster BA 2fach Tasterstellung Art.-Nr.: 2072.01 LED Farbe: schwarz
3147
LS 995 KO5P SW 2-GANG ROCKER WITH SYMBOLS AND TRANSPARENT LENS FOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
3154 800 NT 1-GANG ROCKER FOR 1-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Push button BCU 1-gang rocker with lens for 1-gang push-button BCU neutral position ref.-no.: 8071.02 LED W switch position ref.-no.: 8071.01 LED W Version: with lens Manufacturer: JUNG Ref.-no.: 800 NT
3154
800 NT 1-GANG ROCKER FOR 1-GANG PUSH-BUTTON BCU SIN FAMILIA
3155 800 P 1-GANG ROCKER WITH SYMBOLS, FOR 1-GANG PUSH-BUTTON BCU PUSH BUTTONS
KNX Push button BCU 1-gang rocker with lens and symbols for 1-gang push-button BCU neutral position ref.-no.: 8071.02 LED W Version: with symbols and lens Manufacturer: JUNG Ref.-no.: 800 P
3155
800 P 1-GANG ROCKER WITH SYMBOLS, FOR 1-GANG PUSH-BUTTON BCU PUSH BUTTONS
3156 800 NA 1-GANG ROCKER WITH INSCRIPTION PLATE FOR 1-GANG PUSH-BUTTON BCU PUSH BUTTONS
Rocker with inscription field 1-gang rocker for 1-gang push-button BCU neutral position ref.-no.: 8071.02 LED W switch position ref.-no.: 8071.01 LED W (illumination possible, see insert) Version: with inscription field 22 x 48 mm Manufacturer: JUNG Ref.-no.: 800 NA
3156
800 NA 1-GANG ROCKER WITH INSCRIPTION PLATE FOR 1-GANG PUSH-BUTTON BCU PUSH BUTTONS
3157 800 KO 1-GANG ROCKER WITH RED TRANSPARENT LENS FOR 1-GANG PUSH-BUTTON BCU PUSH BUTTONS
KNX Push button BCU 1-gang rocker with great lens for 1-gang push-button BCU neutral position ref.-no.: 8071.02 LED W switch position ref.-no.: 8071.01 LED W Version: with red symbol Manufacturer: JUNG Ref.-no.: 800 KO
3157
800 KO 1-GANG ROCKER WITH RED TRANSPARENT LENS FOR 1-GANG PUSH-BUTTON BCU PUSH BUTTONS
3158 33 AN L Accessories and spare parts Symbols SIN FAMILIA
Accessories and spare parts Symbols für Wipp-Kontrollschalter und Taster im Programm WG 800 Colour: anthracite Version: symbol light Manufacturer: JUNG Ref.-no.: 33 AN L
3158
33 AN L ACCESSORIES AND SPARE PARTS SYMBOLS SIN FAMILIA
3159 33 AN K Accessories and spare parts Symbols SIN FAMILIA
Accessories and spare parts Symbols für Wipp-Kontrollschalter und Taster im Programm WG 800 Colour: anthracite Version: symbol light Manufacturer: JUNG Ref.-no.: 33 AN L
3159
33 AN K ACCESSORIES AND SPARE PARTS SYMBOLS SIN FAMILIA
3160 33 AN T Accessories and spare parts Symbols SIN FAMILIA
Accessories and spare parts Symbols für Wipp-Kontrollschalter und Taster im Programm WG 800 Colour: anthracite Version: symbol door Manufacturer: JUNG Ref.-no.: 33 AN T
3160
33 AN T ACCESSORIES AND SPARE PARTS SYMBOLS SIN FAMILIA
3161 33 AN N Accessories and spare parts Symbols SIN FAMILIA
Accessories and spare parts Symbols für Wipp-Kontrollschalter und Taster im Programm WG 800 Colour: anthracite Version: neutral Manufacturer: JUNG Ref.-no.: 33 AN N
3161
33 AN N ACCESSORIES AND SPARE PARTS SYMBOLS SIN FAMILIA
3163 33 GN SYMBOLS FOR SWITCHES WITH INDICATOR LIGHT SIN FAMILIA
Symbols für Wippen Art.-Nrn.: CD 590 KO .. und CD 590 NAKO .. für Abdeckungen Art.-Nrn.: 5560 KO, 5561 KO, 5560 KO WW und 5561 KO WW für Wipp-Kontrollschalter und Taster im Programm WG 600 für Wipp-Kontrollschalter und Taster im Programm AP 600 Colour: green Version: neutral Manufacturer: JUNG Ref.-no.: 33 GN
3163
33 GN SYMBOLS FOR SWITCHES WITH INDICATOR LIGHT SIN FAMILIA
3164 33 KLAR SYMBOLS FOR SWITCHES WITH INDICATOR LIGH AND PUSH-BUTTONS SIN FAMILIA
Symbols für Wippen Art.-Nrn.: CD 590 KO .. und CD 590 NAKO .. für Abdeckungen Art.-Nrn.: 5560 KO, 5561 KO, 5560 KO WW und 5561 KO WW für Wipp-Kontrollschalter und Taster im Programm WG 600 für Wipp-Kontrollschalter und Taster im Programm AP 600 Colour: transparent Manufacturer: JUNG Ref.-no.: 33 KLAR
3164
33 KLAR SYMBOLS FOR SWITCHES WITH INDICATOR LIGH AND PUSH-BUTTONS SIN FAMILIA
3165 33 NR SYMBOLS FOR SWITCHES WITH INDICATOR LIGHT AND PUSH-BUTTONS SIN FAMILIA
Symbols für Wippen Art.-Nrn.: CD 590 KO .. und CD 590 NAKO .. für Abdeckungen Art.-Nrn.: 5560 KO, 5561 KO, 5560 KO WW und 5561 KO WW für Wipp-Kontrollschalter und Taster im Programm WG 600 für Wipp-Kontrollschalter und Taster im Programm AP 600 Colour: red Version: neutral Manufacturer: JUNG Ref.-no.: 33 NR
3165
33 NR SYMBOLS FOR SWITCHES WITH INDICATOR LIGHT AND PUSH-BUTTONS SIN FAMILIA
3168 805 NT 2-GANG ROCKERFOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA
KNX Push button BCU 2-gang rocker with lens for 2-gang push-button BCU neutral position ref.-no.: 8072.02 LED W switch position ref.-no.: 8072.01 LED W Version: with lens Manufacturer: JUNG Ref.-no.: 805 NT
3168
805 NT 2-GANG ROCKERFOR 2-GANG PUSH-BUTTON BCU SIN FAMILIA