Web Code
|
Reference
|
Description
|
Category
|
Price
|
|
3182 |
49550 |
Fan coil controller
Actor, single |
CLIMATE CONTROL |
|
Technical data
- used for controlling fan convectors with max. 3-speed fan motors / air-conditioners
- controlling of room temperature in cooling or heating mode
- KNX/EIB bus coupling for actuating the fan coil control unit via operator panels
or via the building management system
- setpoint adjustment and selection via KNX/EIB bus
- recording of actual temperature via local temperature sensor or KNX/EIB temperature
sensor
- PI controller
- PWM control for thermal valve drives or three-step control for motor-operated
valve drives
- connection for temperature sensor, window contact, overflow contact for condensed
water drip trays
- output for valve drives 24VAC-230VAC
- potential-free inputs for window contact
- outputs for multistage fan control or switch output with KNX/EIB object
- valve control variable may be parameterized as an object for the compatible
KNX/EIB actuators
- the sequence of the different fan speeds may be defined at the start (0-1-2-3 or
0-3-1-2-3)
- operating voltage 24 VAC
- for mounting on DIN rails |
3182
|
49550
|
FAN COIL CONTROLLER
ACTOR, SINGLE
|
CLIMATE CONTROL
|
|
|
3184 |
49582/X |
Room control unit with 2 push-buttons,
housing of stainless steel,
without temperature sensor |
CLIMATE CONTROL |
|
T e c h n i c a l d a t a
approx. 50 g
70 x 70 x 15 mm
EN 50090-2-2
EN 50090-2-2 / EN 61000-6-2 / EN 61326-1997
2-pole KNX/EIB connector
SELV DC 24 V
failure rate 815 fit at 40°C
separate bus coupler with mounting plate,
General data
direct control of heating actuators
- for controlling the fancoil controllers
No. 49550/49551/49552
- direct connection to KNX/EIB
- bus coupler not included
- control knob for temperature setpoint adjustment: the
basic set temperature of the fancoil controller may thus
be modified within a parametrable range of values
- the push-button for fan speed enables the fan stage of
the fancoil controller to be modified
- with the push-button for presence sensing it may be
toggled between normal mode (comfort) and lowering
mode (standby)
- with indicators (LEDs) showing the operating mode of
the fancoil controller (heating/ cooling, fan speed, etc.)
- meant for fixed installations in dry media, it has to be
installed in flush-mounted or surface-mounted boxes |
3184
|
49582/X
|
ROOM CONTROL UNIT WITH 2 PUSH-BUTTONS,
HOUSING OF STAINLESS STEEL,
WITHOUT TEMPERATURE SENSOR
|
CLIMATE CONTROL
|
|
|
3185 |
49581/X |
Room control unit with 2 push-buttons,
plastic housing, white
without temperature sensor |
CLIMATE CONTROL |
|
T e c h n i c a l d a t a
Room control unit RCM to fancoil controller KNX/EIB
without temperature sensor
approx. 25 g
55 x 55 x 15 mm
EN 50090-2-2
EN 50090-2-2 / EN 61000-6-2 / EN 61326-1997
white, further colours are available on request
2-pole KNX/EIB connector
SELV DC 24 V
failure rate 815 fit at 40°C
separate bus coupler with mounting plate, included
1 pce.
General data
- direct control of heating actuators
- for controlling the fancoil controllers
No. 49550/49551/49552
- direct connection to KNX/EIB
- bus coupler not included
- control knob for temperature setpoint adjustment: the
basic set temperature of the fancoil controller may thus
be modified within a parametrable range of values
- the push-button for fan speed enables the fan stage of
the fancoil controller to be modified
- with the push-button for presence sensing it may be
toggled between normal mode (comfort) and lowering
mode (standby)
- with indicators (LEDs) showing the operating mode of
the fancoil controller (heating/ cooling, fan speed, etc.)
- meant for fixed installations in dry media, it has to be
installed in flush-mounted or surface-mounted boxes
|
3185
|
49581/X
|
ROOM CONTROL UNIT WITH 2 PUSH-BUTTONS,
PLASTIC HOUSING, WHITE
WITHOUT TEMPERATURE SENSOR
|
CLIMATE CONTROL
|
|
|
3183 |
49570 |
Accessories
Temperature sensor, prewired with 2 m cable |
SENSORS |
|
The Woertz flat cable systems are increasingly used in applications for
electrical installations. Their widespread and successful implementation
ranges from buildings with sophisticated technical requirements to those
in which the simplicity and flexibility of the installation plays an important
role.
The modularity of the installation is a characteristic of these systems
which is of particular value since it enables modifications and extensions
to be carried out at a later date without any problems. The time savings
and resulting efficiency can thereby be achieved.
With the flat cable system, it is not necessary to cut the installed cables.
Junctions can be created e.g. for the fan coil controller using special outlet
boxes in the exact position required - even at a later date if necessary. The power supply and data bus interface of the device are implemented
on the same flat cable.
Prefabrication is highly recommended to achieve even greater operating efficiency: the connected appliances may be completely wired beforehand
and fitted with the flat cable boxes. On the building site the connection boxes are then simply placed on the flat cable and the pointed
screws tightened in order to establish the electrical contact.
Since the reliability of the flat cable installation systems is extremely high, they are more and more integrated in very important industrial projects.The Woertz flat cable systems are increasingly used in applications for
electrical installations. Their widespread and successful implementation
ranges from buildings with sophisticated technical requirements to those
in which the simplicity and flexibility of the installation plays an important
role.
The modularity of the installation is a characteristic of these systems
which is of particular value since it enables modifications and extensions
to be carried out at a later date without any problems. The time savings
and resulting efficiency can thereby be achieved.
With the flat cable system, it is not necessary to cut the installed cables.
Junctions can be created e.g. for the fan coil controller using special outlet
boxes in the exact position required - even at a later date if necessary. The power supply and data bus interface of the device are implemented
on the same flat cable.
Prefabrication is highly recommended to achieve even greater operating efficiency: the connected appliances may be completely wired beforehand
and fitted with the flat cable boxes. On the building site the connection boxes are then simply placed on the flat cable and the pointed
screws tightened in order to establish the electrical contact.
Since the reliability of the flat cable installation systems is extremely high, they are more and more integrated in very important industrial projects. |
3183
|
49570
|
ACCESSORIES
TEMPERATURE SENSOR, PREWIRED WITH 2 M CABLE
|
SENSORS
|
|
|
8801 |
51078 |
CAJA DE EMPALMES PARA EMPOTRAR EN SUELO |
SIN FAMILIA |
|
CAJA DE EMPALMES PARA EMPOTRAR EN SUELO |
8801
|
51078
|
CAJA DE EMPALMES PARA EMPOTRAR EN SUELO
|
SIN FAMILIA
|
|
|
8877 |
51082 |
PIEZA PARA FIJACIÓN ENCHUFES PARA CAJAS DE EMPOTRAR DE SUELO |
SIN FAMILIA |
|
|
8877
|
51082
|
PIEZA PARA FIJACIÓN ENCHUFES PARA CAJAS DE EMPOTRAR DE SUELO
|
SIN FAMILIA
|
|
|
8878 |
51072 |
CAJA DE EMPALMES PARA EMPOTRAR EN SUELO |
SIN FAMILIA |
|
|
8878
|
51072
|
CAJA DE EMPALMES PARA EMPOTRAR EN SUELO
|
SIN FAMILIA
|
|
|
18059 |
49552 |
Fan Coil Actuator 24vac |
CLIMATE CONTROL |
|
REG fan coil regulator, gray plastic housing, with digital outputs, actual temperature detection by local or KNX temperature sensor, (1 TE = 18 mm), IP20, for cooling, without power supply, regulation of 1 to 3-stage fan convectors / Air-conditioning, control of room temperature in cooling operation, 70 × 107 × 58 mm |
18059
|
49552
|
FAN COIL ACTUATOR 24VAC
|
CLIMATE CONTROL
|
|