Order by:   Filter results: 
Web Code Reference Description Category Price
5275 647393 Switch actuator REG-K/8x230/16 with manual mode ACTUATORS - OUTPUTS
For independent switching of two loads via make contacts. With integrated bus coupler and screw terminals. For installation on DIN rails EN 50022. The 230 V switch output can be operated with a manual switch. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded. KNX software functions: Operation as break or make contact, delay functions for each channel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus voltage failure and recovery, parameterisable download behaviour. Nominal voltage: AC 230 V, 50-60 Hz For each switching contact: Nominal current: 16 A, cos? = 0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA Capacitive load: AC 230 V, 16 A, max. 200 ?F Device width: 2.5 modules = approx. 45 mm
5275
647393 SWITCH ACTUATOR REG-K/8X230/16 WITH MANUAL MODE ACTUATORS - OUTPUTS
1455 576397 Multiple control relay for roller shutters REG 2 A, AC 250 V ACTUATORS - OUTPUTS
For installation on DIN rails. For controlling up to 2 roller shutter motors locally, in groups or centrally. With separation of load and control circuit, as well as forced locking in both directions of movement. Motors are controlled individually using a roller shutter rocker switch and centrally using the blind time switches or blind push-buttons of the Merten blind control system. Mains voltage: AC 230 V, 50 Hz ±10 % Power consumption: 10 mA in relay operation Switching voltage: max. AC 250 V Switching current: max. 2 A Temperature range: 0 -60 °C Terminals: max. 1.5 mm2 Device width: 2 modules = approx. 36 mm
1455
576397 MULTIPLE CONTROL RELAY FOR ROLLER SHUTTERS REG 2 A, AC 250 V ACTUATORS - OUTPUTS
1456 576398 Multiple control relay for roller shutters,flush-mounted ACTUATORS - OUTPUTS
Suitable for a size 60 flush-mounted box. Flat 22 mm design. For local control using push-buttons, installation in a deep flush-mounted box. For controlling up to 2 roller shutter motors locally, in groups or centrally. With separation of load and control circuit, as well as forced locking in both directions of movement. Motors are controlled individually using a roller shutter rocker switch and centrally using the blind time switches or blind push-buttons of the Merten blind control system. Mains voltage: AC 230 V/50 Hz ±10% Control voltage: AC 230 V, ±10% Power consumption: 10 mA in relay mode Switching voltage: max. AC 250 V Switching capacity: max. 6 A Temperature range: 0-60 °C Terminals: max. 1.5 mm2 Dimensions: 22x49x52 mm (HxWxD) Installation: (Deep) flush-mounted box
1456
576398 MULTIPLE CONTROL RELAY FOR ROLLER SHUTTERS,FLUSH-MOUNTED ACTUATORS - OUTPUTS
1700 625199 INSTABUS push-button module 1-gang, System M PUSH BUTTONS
EIB push-button module, 1-gang for system m Push-button module without rocker. With programmable status display. ~ In KNX, to be completed with: Rocker for push-button module, 1- gang, art. no. System M6191.., 6251... Rocker for push-button module, 1-gang, with 1/0 imprint, art. no. System M 6193.., 6254... Rocker for push-button module, 1-gang, with up/down arrow imprint, art. no. System M 6194.., 6255...
1700
625199 INSTABUS PUSH-BUTTON MODULE 1-GANG, SYSTEM M PUSH BUTTONS
1705 625299 INSTABUS push-button module 2-gang, System M , white polar PUSH BUTTONS
INSTABUS push-button with push-button module (System M / System Design) On the basis of this installation principle, the push-button module is fully equipped with an integrated bus coupler. The retaining ring for the screw fixing is attached to the installation box. The physical address is programmed after the bus connection terminal with push-button and LED is plugged on to the back of the push-button module. The rocker is plugged onto the push-button module in the desired colour. Push-button module and frame are then put on to the retaining ring. The push-button module provides you with two or four button surfaces, two in the case of 1-gang push-buttons and four in the case of 2-gang push-buttons. t The keys can be programmed to carry out the following functions: switching, dimming, controlling blinds and retrieving scenes. Available push-button modules: • 1-gang and 2-gang for System M
1705
625299 INSTABUS PUSH-BUTTON MODULE 2-GANG, SYSTEM M , WHITE POLAR PUSH BUTTONS
1716 626199 INSTABUS push-button module 1-gang, System Design PUSH BUTTONS
For System Design Push-button module without rocker. With programmable status display. The Merten push-button module provides you with the following: – one button/two operating surfaces in the case of a 1-gang push-button – two buttons/four operating surfaces in the case of the 2-gang push-button The push-buttons can be set to perform various functions, allowing you, for example, to switch lighting on and off or dim it, to control the blinds or to retrieve stored scenes. In KNX, to be completed with: Rocker for 1-gang push-button module, art. no. System Design 6261... Rocker for push-button module, 1-gang, with 1/0 imprint, art. no. System Design 6264. Rocker for push-button module, 1-gang, with up/down arrow imprint, art. no. System Design 6265..
1716
626199 INSTABUS PUSH-BUTTON MODULE 1-GANG, SYSTEM DESIGN PUSH BUTTONS
1722 626299 INSTABUS push-button module 2-gang, System Design PUSH BUTTONS
For System Design Push-button module without rocker. With programmable status display. The Merten push-button module provides you with the following: - one button/two operating surfaces in the case of a 1-gang push-button - two buttons/four operating surfaces in the case of the 2-gang push-button The push-buttons can be set to perform various functions, allowing you, for example, to switch lighting on and off or dim it, to control the blinds or to retrieve stored scenes. In KNX, to be completed with: Rockers for 2-gang push-button module, art. no. System Design 6262... Rockers for push-button module, 2-gang, with 1/0 and up/down arrow imprint, art. no. System Design 6266... Rockers for push-button module, 2-gang, with up/down arrow and 1/0 imprint, art. no. System Design 6267... Rockers for push-button module, 2-gang, with up/down arrow imprint, art. no. System Design 6268
1722
626299 INSTABUS PUSH-BUTTON MODULE 2-GANG, SYSTEM DESIGN PUSH BUTTONS
1747 629993 Switch actuator, flush-mounted/230/16 polar white ACTUATORS - OUTPUTS
Switch actuator, flush-mounted/230/16 External auxiliary voltage: none Power supply from the bus: DC 24 V/approx. 10 mA Insulation voltage: 4 kV between bus and AC 230 V Switch contacts: 1 x make contacts Nominal voltage: AC 230 V, 50 to 60 Hz Nominal current: 16 A at cos ? = 1 10 A inductive load at cos ? = 0.6 Connected load: Incandescent lamps: AC 230 V, max. 2700 W with 20,000 switching cycles Halogen lamps: AC 230 V, max. 1700 W with 20,000 switching cycles Fluorescent lamps: AC 230 V, max. 1000 VA, with parallel correction, with 5,000 switching cycles Capacitive load: AC 230 V, 10 A, max. 105 µF with 5,000 switching cycles Fuse: The switch contact must be protected by a seriesconnected circuit-breaker Switching frequency: max. 10 per minute at nominal load Ambient temperature: Operation: -5 °C to +45 °C Storage: -25 °C to +55 °C Transport: -25 °C to +70 °
1747
629993 SWITCH ACTUATOR, FLUSH-MOUNTED/230/16 POLAR WHITE ACTUATORS - OUTPUTS
1786 647893 Switch actuator REG-K/8x230/16 with manual mode ACTUATORS - OUTPUTS
For independent switching of 8 loads via make contacts. All 230 V switch outputs can be operated with manual switches. With integrated bus coupler. For installation on DIN rails EN 50022. The device is connected to the mains via screw terminals; every second L connection is bridged internally. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded. KNX software functions: Operation as break or make contact, delay functions for each channel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus voltage failure and recovery, parameterisable download behaviour. Nominal voltage: AC 230 V, 50-60 Hz Per switch contact: Nominal current: 16 A, cos?? =0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA Capacitive load: AC 230 V, 16 A, max. 200 µF Device width: 8 modules = approx. 144 mm Contents: With bus connecting terminal and cable cover.
1786
647893 SWITCH ACTUATOR REG-K/8X230/16 WITH MANUAL MODE ACTUATORS - OUTPUTS
1790 648493 Switching actuator REG-K/12x230/16 with manual actuation ACTUATORS - OUTPUTS
For independent switching of 12 loads via make contacts. All 230 V switch outputs can be operated with manual switches. With integrated bus coupler. The device is connected to the mains via screw terminals; every second L connection is bridged internally. For installation on DIN rails EN50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded. KNX software functions: Operation as break or make contact, delay functions for each channel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus voltage failure and recovery, parameterisable download behaviour. Nominal voltage: AC 230 V, 50-60 Hz Per switch contact: Nominal current: 16 A, cos?? =0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA Capacitive load: AC 230 V, 16 A, max. 200 µF Device width: 12 modules = approx. 216 mm Contents: With bus connecting terminal and cable cover.
1790
648493 SWITCHING ACTUATOR REG-K/12X230/16 WITH MANUAL ACTUATION ACTUATORS - OUTPUTS
1799 649808 Blind actuator REG-K/8x/10 with manual mode ACTUATORS - OUTPUTS
Zum unabhängigen Steuern von 8 Jalousie- /Rollladenantrieben. Die Funktion der Jalousiekanle ist frei konfigurierbar. Alle Jalousieausgänge lassen sich mit Tasten manuell betätigen. Mit integriertem Busankoppler. Für die Montage auf DIN-Hutschienen EN 50022. Der Busanschluss erfolgt übe reine Busanschlussklemme, eine Datenschiene ist nicht erforderlich. Anzeige der Kanalzustnde über LEDs. Eine grüne LED zeigt die Betriebsbereitschaft an. Softwarefunktionen KNX: Jalousiefunktionen: Jalousietyp. Laufzeit. Pausenzeit. Schrittzeit. Differenzierte Sperrfunktionen und Wetteralarme. 8-Bit-Positionierung für Höhe und Lamelle. Szenen. Hand- /Automatikfunktion. Differenzierte Status- und Rückmeldefunktionen. Je Jalousieausgang: Nennspannung: AC 230 V, 50-60 Hz Nennstrom: 10 A, cos Phi = 0,6 Motorlast: AC 230 V, max. 1000 W Externe Hilfsspannung: AC 110-240 V, 50- 60 Hz, max. 2 VA Gertebreite: 8 TE = ca. 144 mm Ausführung: lichtgrau Fabrikat: Merten Art.-Nr.: 649808 oder gleichwertig
1799
649808 BLIND ACTUATOR REG-K/8X/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
1832 663591 Wind sensor with 0-10 V interface SENSORS
Wind sensor with 0-10 V interface the wind sensor evaleates the wind speed and converts it into an analogue 0-10 V output voltage. For external installation and connection to the weather station REG-K/4-gang or the analogue input REG-K/4-gang. These two devices provide the supply voltage necessary to operate the sensor. Measuring range: 0.7 ... 40 m/s, linear Output: 0 ... 10 V External power supply: Voltage: 24 V DC (18-32 V DC) Power consumption: approx. 12 mA General specifications: Type of protection: IP 65 Load: max. 60 m/s transient Incoming cable: 3 m, LiYY 6 x 0.25 mm2 Fixing method: Mounting bracket Mounting position: vertical ˜ In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Analogue input module REG/4-gang, art. no. 682192. — Contents: With mounting bracket
1832
663591 WIND SENSOR WITH 0-10 V INTERFACE SENSORS
1833 663592 Wind sensor with 0-10 V interface and heating SENSORS
Wind sensor with 0-10 V interface and heating. The wind sensor evaluates the wind speed and converts it into an analogue 0-10 V output voltage. The integrated heater can be operated via an external power supply of AC 24 V/500 mA for troublefree operation in frosty weather. For external installation and connection to the weather station REG-K/4-gang or the analogue input REG-K/4-gang. These two devices provide the supply voltage necessary to operate the sensor. Measuring range: 0.7 ... 40 m/s, linear Output: 0 ... 10 V External power supply: Voltage: 24 V DC (18-32 V DC) Power consumption: approx. 12 mA Heating: 24 V DC/AC PTC element (80° C) General specifications: Type of protection: IP 65 Load: max. 60 m/s transient Incoming cable: 3 m, LiYY 6 x 0.25 mm2 Fixing method: Mounting bracket Mounting position: vertical ˜ In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Analogue input module REG/4-gang, art. no. 682192. Accessories: Power supply REG, AC 24 V / 1 A, art. no. 663529. — Contents: With mounting bracket polar white
1833
663592 WIND SENSOR WITH 0-10 V INTERFACE AND HEATING SENSORS
1835 663594 Twilight sensor SENSORS
Twilight sensor The twiliht sensor is required to recod and evaluate brightness. Brightness is recorded via a photoelectric diode and electronically converted into an analogue output signal of 0 V - 10 V. For external installation and connection to the weather station REG-K/4-gang or the analogue input REG-K/4-gang. These two devices provide the supply voltage necessary to operate the sensor. Measuring range: 0 to 255 lux, linear Output: 0 ... 10 V short-circuit-proof External power supply: Voltage: 24 V DC (15-30 V DC) Power consumption: approx. 5 mA General specifications: Incoming cable: using PG7 screw fitting Recommended cable: 3 x 0.25 mm2 Type of protection: IP 65 Dimensions: 58 x 35 x 64 (W x H xD) ˜ In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Analogue input module REG/4-gang, art. no. 682192
1835
663594 TWILIGHT SENSOR SENSORS
1836 663595 Rain sensor SENSORS
Rain sensor The rain sensor is used to record and evaluate precipitation and is intended for external mounting. A sensor evaluates the conductivity of the rainwater. The heating is controlled by a microprocessor which supplies an output signal of 0 V or 10 V. The end of the rainfall can be recorded almost immediately with the help of an in-built heater. The heater requires an additional voltage of 24 V AC or DC. For external installation and connection to the weather station REG-K/4-gang or the analogue input REG-K/4-gang. These two devices provide the supply voltage necessary to operate the sensor. Output: 0 V dry, 10 V rain External power supply: Voltage: 24 V DC (15-30 V DC) Power consumption: approx. 10 mA (without heating) Heating: 24 V DC/AC max. 4.5 W General specifications: Type of protection: IP 65 Incoming cable: 3 m, UYY 5 x 0.25 mm2 Fixing method: Mounting bracket Mounting position: approx. 45° ˜ In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Analogue input module REG/4-gang, art. no. 682192. Accessories: Power supply REG, AC 24 V / 1 A, art. no. 663529. — Contents: With holder for installing the sensor on walls and masts.
1836
663595 RAIN SENSOR SENSORS
1837 663596 Temperature sensor SENSORS
Temperature sensor The temperature is measured with the temperature sensor and converted into an analogue output signal of 0-10 V. For external installation and connection to the weather station REG-K/4-gang or the analogue input REG-K/4-gang. These two devices provide the supply voltage necessary to operate the sensor. Measuring range: -30° C to +70° C linear Output: 0 ... 10 V short-circuit-proof External power supply: Voltage: 24 V DC (15-30 V DC) Power consumption: approx. 3 mA General specifications: Incoming cable: using PG7 screw fitting Recommended cable: 3 x 0.25 mm2 Type of protection: IP 65 Dimensions: 58 x 35 x 64 (W x H x D) ˜ In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Analogue input module REG/4-gang, art. no. 682192
1837
663596 TEMPERATURE SENSOR SENSORS
1840 663692 Weather combi-sensor DCF-77 SENSORS
The weather combi-sensor includes a wind sensor, precipitation sensor, twilight sensor and three brightness sensors (East, South, West). With integral DCF-77 receiver, antenna rotatable through 45° and integral heating. Suitable for external installation on a wall or on a mast. The sensor is connected to a weather station REG-K/4-gang. The weather data is evaluated in the weather station. The necessary power supplies are provided by the weather station with connected power supply REG. Power supply: AC 24 V (+/- 15 %) Power consumption: max. 600 mA (with heating) Sensors: 6 Wind speed: 1 ... 40 m/s (?? 0.5 m/s) Brightness: 0 ... 110 klux (+/- 10 %) Twilight 0 ... 250 lux Type of protection: IP 65 when installed Temperature range: - 40 °C ... + 60 °C (non-icing) Fixing method: Mounting bracket Dimensions: 130x200 mm (??xH) In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Note: If weather-dependent automatic functions are to be carried out, use the blind actuators art. no. 6498...
1840
663692 WEATHER COMBI-SENSOR DCF-77 SENSORS
1843 668091 DCF-77 antenna TIME TRANSMITTERS - SWITCHES
The DCF-77 antenna is connected to the year time switch REG/4/324 DCF-77 (art. no. 677029). Using the antenna, the DCF receiver in the year time switch can receive the DCF-77 time signal via radio to synchronise the clock. The antenna should be connected to a year time switch REG-K/4/324 DCF-77. Type of protection: IP 65 ˜ In KNX, to be completed with: Year time switch REG-K/4/324 DCF-77, art. no. 677029, KNX Time sender REG-K Art. Nr. 677290. — Contents: With mounting bracket.
1843
668091 DCF-77 ANTENNA TIME TRANSMITTERS ...
1845 668990 Lead gel battery DC 12 V, 7,2 Ah SYSTEM DEVICES
Lead gel battery Lead gel battery to connect to the emergency input of the power supply 320 REG-K with battery connection. Also for powering the outdoor siren with flashlight, TeleConnect or IC 1 Internet controller. Nominal voltage: DC 12 V Capacity: 7.2 Ah ˜ In KNX, to be completed with: Power supply 320 REG-K with battery connection, art. no. 683129.
1845
668990 LEAD GEL BATTERY DC 12 V, 7,2 AH SYSTEM DEVICES
1850 671198 Bus coupling unit insert, 1-gang without neutral position PUSH BUTTONS
Bus coupling insert, 1-gang The rocker for switches and push-button switches, the rocker marked "0"/ "1", the rocker with labelling field and the rocker with opening for symbols from System Basis, System Design and OctoColor can all be fitted on the 1-gang bus coupling insert. With programmable operating or status display for rockers with opening for symbols. We can also adapt the switch ranges AQUADESIGN, AQUACLASSIC and ANTI-VANDALISM for the 1-gang bus coupling insert as a special version. With integrated bus coupler. In the version with middle position, the rockers can be moved up and down (three-way rocker). In the version without middle position, telegrams are only generated when the lower half of the rocker is pressed (twoway rocker). For mounting in the size 60 installation box. With push-button and LED for programming. KNX software functions: For art. no. 671198: Switching. Toggling. Status display. For art. no. 671199: Switching. Dimming. Blinds. Toggling. Status display
1850
671198 BUS COUPLING UNIT INSERT, 1-GANG WITHOUT NEUTRAL POSITION PUSH BUTTONS
1851 671199 Bus coupling unit insert, 1-gang with neutral position PUSH BUTTONS
Bus coupling insert, 1-gang The rocker for switches and push-button switches, the rocker marked "0"/ "1", the rocker with labelling field and the rocker with opening for symbols from System Basis, System Design and OctoColor can all be fitted on the 1-gang bus coupling insert. With programmable operating or status display for rockers with opening for symbols. We can also adapt the switch ranges AQUADESIGN, AQUACLASSIC and ANTI-VANDALISM for the 1-gang bus coupling insert as a special version. With integrated bus coupler. In the version with middle position, the rockers can be moved up and down (three-way rocker). In the version without middle position, telegrams are only generated when the lower half of the rocker is pressed (twoway rocker). For mounting in the size 60 installation box. With push-button and LED for programming. KNX software functions: For art. no. 671198: Switching. Toggling. Status display. For art. no. 671199: Switching. Dimming. Blinds. Toggling. Status display
1851
671199 BUS COUPLING UNIT INSERT, 1-GANG WITH NEUTRAL POSITION PUSH BUTTONS
1852 671298 Bus coupling unit insert, 2-gang without neutral position PUSH BUTTONS
Bus coupling insert, 2-gang the rocke for tho-cicuit switches, rocker for roller shutter switches and push-buttons from System Basis, System M, System Design and OCTOCOLOR can all be fitted on the 2-gang bus coupling insert. We can also adapt the switch ranges AQUADESIGN and AQUACLASSIC for the 2-gang bus coupling insert as a special version. With integrated bus coupler. In the version with middle position, the rockers can be moved up and down (three-way rocker). In the version without middle position, telegrams are only generated when the lower half of the rocker is pressed (twoway rocker). For mounting in the size 60 installation box. With push-button and LED for programming. KNX software functions: For art. no. 671298: Switching. Toggling. Dimming. 1 group of blinds. For art. no. 671299: Switching. Toggling. Dimming. 2 groups of blinds without middle position
1852
671298 BUS COUPLING UNIT INSERT, 2-GANG WITHOUT NEUTRAL POSITION PUSH BUTTONS
1853 671299 Bus coupling unit insert, 2-gang with neutral position PUSH BUTTONS
Bus coupling insert, 2-gang the rocker for tho-circuit switches, the rocker for roller shutter switches and push-buttons from System Basis, System M, System Design and OCTOCOLOR can all be fitted on the 2-gang bus coupling insert. We can also adapt the switch ranges AQUADESIGN and AQUACLASSIC for the 2-gang bus coupling insert as a special version. With integrated bus coupler. In the version with middle position, the rockers can be moved up and down (three-way rocker). In the version without middle position, telegrams are only generated when the lower half of the rocker is pressed (twoway rocker). For mounting in the size 60 installation box. With push-button and LED for programming. KNX software functions: For art. no. 671298: Switching. Toggling. Dimming. 1 group of blinds. For art. no. 671299: Switching. Toggling. Dimming. 2 groups of blinds.
1853
671299 BUS COUPLING UNIT INSERT, 2-GANG WITH NEUTRAL POSITION PUSH BUTTONS
1920 681799 USB interface, flush-mounted GATEWAYS
USB interface, flush-mounted For connecting a programming or diagnostics device with a USB1.1 or USB2 interface to the INSTABUS EIB. For screw mounting in the size 60 installation box. With integrated bus coupler. The device is connected to the bus with a bus connecting terminal. Compatible with ETS 3. Mounting depth: 20 mm ˜ To be completed with:Central plate for telephone socket-outlet TAE, art. no. System M 2960.., 2979.., System Design 2978... — Contents: With bus connecting terminal
1920
681799 USB INTERFACE, FLUSH-MOUNTED GATEWAYS
1921 681829 USB interface REG-K GATEWAYS
USB interface REG-K For connecting a programming or diagnostics device with a USB1.1 or USB2 interface to the INSTABUS EIB. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. With integrated bus coupler. Device width: 2 modules = approx. 36 mm — Contents: With bus connecting terminal and cable cover
1921
681829 USB INTERFACE REG-K GATEWAYS
1924 682191 Analogue input REG-K/4-gang INPUTS
Analogue input REG-K 4-gang The analogue input records and processes analogue sensor signals. Up to four analogue sensors can be connected in any combination. In connection with the analogue input module REG/4-gang, 8 analogue inputs are available, to which the connection is made using the sub-bus. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. Evaluation and limit value processing is performed in the analogue input. With continuity checking of the 4 ... 20 mA inputs. Auxiliary voltage: AC 24 V (+/-10 %) Analogue inputs: 4 Current interface: 0 ... 20 mA, 4 ... 20 mA Voltage interface: 0 ... 1 V, 0 ... 10 V Outputs: DC 24 V, 100 mA Continuity checking: 4 ... 20 mA Device width: 4 modules = approx. 72 mm In KNX, to be completed with: Power supply REG, AC 24 V / 1 A, art. no. 663529. Accessories: Analogue input module REG/4-gang, art. no. 682192. Wind sensor with 0-10 V interface, art. no. 663591. Wind sensor with 0-10 V interface and heating, art. no. 663592. Rain sensor, art. no. 663595. Brightness sensor, art. no. 663593: Twilight sensor, art. no. 663594: Temperature sensor, art. no. 663596. Contents: With bus connecting terminal and cable cover.
1924
682191 ANALOGUE INPUT REG-K/4-GANG INPUTS
1925 682192 Analogue input module REG/ 4-gang SENSORS
Analogue input module REG/ 4-gang Extension module to extend weather station REG-K/4-gang and analogue input REG-K/4-gang from 4 to 8 analogue outputs. Connections are made using the sub-bus. Up to four analogue sensors can be connected in any combination. For installation on DIN rails EN 50022. Evaluation and limit value processing is performed in the analogue input or weather station. With continuity checking of the 4 ... 20 mA inputs. Auxiliary voltage: AC 24 V (+/-10 %) Rating: max. 4 VA Analogue inputs: 4 Current interface: 0 ... 20 mA, 4 ... 20 mA Voltage interface: 0 ... 1 V, 0 ... 10 V (DC) A/D conversion: 14 bit Outputs: DC 24 V, 100 mA Continuity checking: 4 ... 20 mA Device width: 4 modules = approx. 72 mm In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Power supply REG, AC 24 V / 1 A, art. no. 663529. Accessories: Wind sensor with 0-10 V interface, art. no. 663591. Wind sensor with 0-10 V interface and heating, art. no. 663592. Rain sensor, art. no. 663595. Brightness sensor, art. no. 663593: Twilight sensor, art. no. 663594: Temperature sensor, art. no. 663596. — Contents: With sub-bus jumper
1925
682192 ANALOGUE INPUT MODULE REG/ 4-GANG SENSORS
1926 682291 Analogue actuator REG-K/4-gang ACTUATORS - OUTPUTS
Analogue actuator REG-K/4-gang The output channels can be parameterised for different current and voltage signals to control different analogue variables (e.g. servomotors). The actuator has four analogue outputs. For use in connection with the analogue actuator module REG/4-gang, 8 analogue outputs are provided. Connections are made using the sub-bus. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. With continuity checking of the current outputs. Auxiliary voltage: AC 24 V (+/-10 %) Analogue outputs: 4 Current signals: 0 ... 20 mA, 4 ... 20 mA Voltage signals: 0 ... 1 V, 0.. 10 V Continuity checking: 4 ... 20 mA Outputs: DC 24 V, 100 mA (total) Device width: 4 modules = approx. 72 mm ˜ In KNX, to be completed with: Power supply REG, AC 24 V / 1 A, art. no. 663529. Accessories: Analogue actuator module REG/4-gang, art. no. 682292. — Contents: With bus connecting terminal and cable cover
1926
682291 ANALOGUE ACTUATOR REG-K/4-GANG ACTUATORS - OUTPUTS
1927 682292 Analogue actuator module REG/ 4-gang ACTUATORS - OUTPUTS
Analogue actuator module REG/ 4-gang Extension module to extend analogue actuator REG-K/4-gang from 4 to 8 analogue outputs. Connections are made using the sub-bus. The output channels can be independently parameterised for different current and voltage signals to control different control values (e.g. servomotors). For installation on DIN rails EN 50022. Auxiliary voltage: AC 24 V (+/-10 %) Analogue outputs: 4 Current signals: 0 ... 20 mA, 4 ... 20 mA Voltage signals: 0 ... 1 V, 0.. 10 V (DC) Continuity checking: 4 ... 20 mA Outputs: DC 24 V, 100 mA (total) Device width: 4 modules = approx. 72 mm ˜ In KNX, to be completed with: Analogue actuator REG-K/4-gang, art. no. 682291. — Contents: With sub-bus jumper.
1927
682292 ANALOGUE ACTUATOR MODULE REG/ 4-GANG ACTUATORS - OUTPUTS
1936 682991 Weather station REG-K/4-gang SENSORS
Weather station REG-K/4-gang The weather station records and processes analogue sensor signals such as wind speed, brightness, twilight, precipitation and a DCF-77 signal. Up to four analogue sensors and the DCF-77 weather combi-sensor can be connected in any combination. In connection with the 4-gang analogue input module, 8 analogue inputs are available, to which the connection is made using the sub-bus. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. If DCF-77 weather combi-sensors are used, it is possible to access a pre-configured setting in the software. The measured values are converted by the weather station into 1 byte / 2 byte telegrams (EIS 6/5 value). This enables bus devices (visualisation software, measured value displays) to access the control processes, generate signals or control weather-dependent processes. Programming is performed using the ETS tool for the weather station
1936
682991 WEATHER STATION REG-K/4-GANG SENSORS
1947 689701 Bus connection terminal, red/dark grey SYSTEM DEVICES
Bus connecting terminal For connecting max. 4 core pairs to an INSTABUS EIB REG-K, flush-mounted, surfacemounted or built-in device, can also be used as a branch terminal. Consists of two interlocked terminal parts in red ("+") and dark grey ("-"), each with 4 plug-in terminals. For solid conductors with a diameter of 0.6 to 0.8 mm.
1947
689701 BUS CONNECTION TERMINAL, RED/DARK GREY SYSTEM DEVICES
4692 670804 Push-button interface 4-gang plus INPUTS
green Input 3 (art. no. 680704 only) 3. Technical data Initialisation: After a bus voltage failure or a bus resetthe push-button interface will not be ready for operation for at least 17 seconds. Power supply from the bus: DC 24 V/< 10 mA Inputs: Use: connection of floating contacts Contact resistance: < 500 O (with closed contact) Outputs: Use: connection of low-current LEDs (< 1 mA) Contact voltage Uk: < 3 V (SELV) Contact current: < 0.5 mA Display element: programming LED Operating element:programming button Ambient temperature: Operation -5 °C to +45 °C Storage -25 °C to +55 °C Transport -25 °C to +70 °C Max. humidity: 93 % relative humidity, no moisture condensation Environment: the device is designed for use at up to 2000 m above sea level (MSL). Protection class: II Type of protection: IP 20 Connections: Inputs, outputs: Art. no. 670802 each 2 and GD, single-core Art. no. 670804 each 4 and GD, single-core Maximum cable length: 7.5 m
4692
670804 PUSH-BUTTON INTERFACE 4-GANG PLUS INPUTS
4693 646630 Dimming actuator REG-K/2X230/300W ACTUATORS - OUTPUTS
For switching and dimming incandescent lamps and dimmable, wound transformers (ohmic / inductive load). (Phase control) With integral bus coupler, plug-in screw terminals, short-circuit and overload protection and soft start function to protect the lamps. For installation onto DIN rails EN 50022. Bus connection is via bus terminals, a data rail is not necessary. Readiness for operation is indicated by a green LED after the application has been loaded, and an overload of one channel or both channels is indicated by a flashing light. KNX software functions: Starting behaviour, memory function, dimming speed, switching off by relative dimming, configurable minimum brightness and behaviour on bus voltage failure/recovery are programmable. Nominal voltage: AC 230 V, 50 Hz Nominal power: per channel: max. 300 W/VA per channel: max. 300 W/VA Minimum load: 25 W/VA Short-circuit protection: via fuse Device width: 6 modules = approx. 108 mm Contents: With bus connecting terminal and cable cover.
4693
646630 DIMMING ACTUATOR REG-K/2X230/300W ACTUATORS - OUTPUTS
4694 644692 Binary input REG-K/ 8x230 INPUTS
Binary input REG-K/8x230 For connecting eight conventional devices with AC 230 V outputs to the KNX. With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded. KNX software functions: Switching, dimming or blind control via 1 or 2 inputs. Positioning values for blind control (8-bit). Pulse edges with 1-, 2-, 4-, or 8-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with 2-byte telegrams. 8-bit linear regulator. Disable function. Break/make contact. Debounce time. Input voltage: AC 230V, 50-60Hz Inputs: 8 Input current: AC approx. 7 mA Line length: max. 100 m Device width: 4 modules = approx. 72 mm - Contents: With bus connecting terminal and cable cover.
4694
644692 BINARY INPUT REG-K/ 8X230 INPUTS
4695 649315 Universal dimming actuator REG-K/4x230/150W ACTUATORS - OUTPUTS
Universal dimming actuator REG-K/4x230/150 W AC 230 V, 50-60 Hz For switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, shortcircuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN 50022. The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of inductive and capacitive loads cannot be connected. Bus connection is via bus terminals, a data rail is not necessary. INSTABUS EIB software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/ without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery. Nominal voltage: AC 220 - 230 V, 50/60 Hz Nominal power/channel: max. 150 W/VA 20 W minimum load (ohmic) 50 VA minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC 230 V, 50/ 60 Hz (same phase as the dimming channels) Device width: 6 modules = approx. 105 mm ˜ Extension unit operation: With mechanical push-buttons (make contact). With extension insert, art. no. 573999, extension TELE insert, art. no. 573998. — Contents: With bus connecting terminal and cable cover.
4695
649315 UNIVERSAL DIMMING ACTUATOR REG-K/4X230/150W ACTUATORS - OUTPUTS
4760 617125 Push-button, 1-gang plus, active white, glossy PUSH BUTTONS
Push-button, 1-gang plus For System M. With integrated bus coupling unit. Push-button with 2 operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions.
4760
617125 PUSH-BUTTON, 1-GANG PLUS, ACTIVE WHITE, GLOSSY PUSH BUTTONS
4808 627544 Push-button, 1-gang plus, white PUSH BUTTONS
Push-button, 1-gang plus For System M. With integrated bus coupling unit. Push-button with 2 operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions.
4808
627544 PUSH-BUTTON, 1-GANG PLUS, WHITE PUSH BUTTONS
4812 627644 Push-button, 2-gang plus, white, System M PUSH BUTTONS
Push-button, 2-gang plus For System M. With integrated bus coupler. Push-button with 5 operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions.
4812
627644 PUSH-BUTTON, 2-GANG PLUS, WHITE, SYSTEM M PUSH BUTTONS
4816 627844 Push-button, 4-gang plus,For System M. With integrated bus coupling unit. white PUSH BUTTONS
Push-button, 4-gang plus For System M. With integrated bus coupling unit. Push-button with 8 operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. The device is connected to the bus line with a bus connecting terminal.
4816
627844 PUSH-BUTTON, 4-GANG PLUS,FOR SYSTEM M. WITH INTEGRATED BUS COUPLING UNIT. WHITE PUSH BUTTONS
4820 627944 Push-button, 4-gang plus with IR,receiver For System M. With integrated bus coupling unit. white GATEWAYS
Im Design System M. Mit integriertem Busankoppler. Taster mit 8 Bedientasten, Betriebs-, Statusanzeige und Schriftfeld. Die Betriebsanzeige kann auch als Orientierungslicht verwendet werden. Die jeweiligen Funktionen der Tasten können mit einer IR-Fernbedienung angesteuert werden. Die Steuerung mit einer Merten Distance- IR-Fernbedienung ist bereits im Taster vorprogrammiert. Viele andere IR- Fernbedienungen (z. B. vorhandene TV- oder CD-Player-Fernbedienung) können am Taster angelernt werden. Das Gerät wird übereine Busanschlussklemme mit der Busleitung verbunden. Softwarefunktionen KNX: Schalten, Umschalten, Dimmen (ein- /zweiflächig), Jalousie (ein- /zweiflächig), Flanken lst 1,- 2-, 4- oder 8-Bit-Telegramme aus (Unterscheidung kurze/lange Betätigung), Flanken mit 2-Byte-Telegrammen (Unterscheidung kurze/lange Betätigung), 8-Bit-Schieberegler, Szenenabruf, Szenenspeicherung, Sperrfunktionen. Zubehr: Beschriftungsbgen fr Multifunktions-Taster mit IR-Empfnger Art.-Nr. 618419/20. Sender: IR-Fernbedienung Distance Art.- Nr. 570222. Material: Thermoplast edelmatt Ausführung: wei Fabrikat: Merten Art.-Nr.: 627944 oder gleichwertig
4820
627944 PUSH-BUTTON, 4-GANG PLUS WITH IR,RECEIVER FOR SYSTEM M. WITH INTEGRATED BUS COUPLING UNIT. WHITE GATEWAYS
4842 644792 Binary input REG-K/8x24 INPUTS
Binary input REG-K/8x24 For connecting 8 conventional devices with AC/ DC 24 V outputs to INSTABUS EIB. With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.
4842
644792 BINARY INPUT REG-K/8X24 INPUTS
4844 649802 Blind actuator REG-K/2x/10 with manual mode ACTUATORS - OUTPUTS
Blind actuator REG-K/2x/10 with manual mode For independent control of 2 blind/roller shutter drives. The function of the blind channels is freely configurable. All blind outputs can be operated manually using push-button operation. With integrated bus coupling unit. For installation onto DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. INSTABUS EIB software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Differentiated disable functions and weather alarms. 8-bit positioning for height and slat. Scenes. Manual/automatic mode. Differentiated status and status feedback functions. For each blind output: Nominal voltage: AC 230 V, 50-60 Hz Nominal current: 10 A, cos? = 0.6 Motor load: AC 230 V, max. 1000 W Device width: 4 modules = approx. 72 mm
4844
649802 BLIND ACTUATOR REG-K/2X/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
4845 649804 Blind actuator REG-K/4x/10 with manual mode ACTUATORS - OUTPUTS
Blind actuator REG-K/4x/10 with manual mode For independent control of 4 blind/roller shutter drives. The functions of the blind channels is freely configurable. All blind outputs can be operated manually using push-button operation. With integrated bus coupling unit. For installation onto DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.
4845
649804 BLIND ACTUATOR REG-K/4X/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
4849 670802 Push-button interface, 2-gang plus INPUTS
Push-button interface, 2-gang plus Generates an internal signal voltage for connecting two conventional push-buttons or floating contacts, and for connecting two low-current LEDs. The cores are 30 cm long and can be extended to max. 7.5 m. For installation in a conventional 60 mm switch box.
4849
670802 PUSH-BUTTON INTERFACE, 2-GANG PLUS INPUTS
5249 646808 Switch actuator REG-K/8x230/6 8-gang ACTUATORS - OUTPUTS
For independent switching of eight loads via make contacts. With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded. KNX software functions: Operation as break or make contact, delay functions for each channel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus voltage failure and recovery, parameterisable download behaviour. Nominal voltage: AC 230 V, 50-60 Hz For each switching contact: Nominal current: 6 A, cos? = 0.6 Incandescent lamps: AC 230 V, max. 1380 W Halogen lamps: AC 230 V, max. 1380 W Fluorescent lamps: AC 230 V, max. 1000 VA Capacitive load: AC 230 V, 6 A, max. 105 ?F Device width: 4 modules = approx. 72 mm
5249
646808 SWITCH ACTUATOR REG-K/8X230/6 8-GANG ACTUATORS - OUTPUTS
5276 649208 Switch actuator REG-K/8x230/10 with manual mode ACTUATORS - OUTPUTS
For independent switching of up to 8 loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-button operation. With integrated bus coupler. For installation on DIN rails EN 50022. Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. KNX software functions: Operation as break contact/make contact. Programmable behaviour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel. Power supply: Nominal voltage: AC 230 V, 50-60 Hz For each switch output: Nominal current: 10 A, cos?? = 1; 10 A, cos? = 0.6 Incandescent lamps: AC 230 V, max. 2000 W Halogen lamps: AC 230 V, max. 1700 W Fluorescent lamps: AC 230 V, max. 1800 W, uncompensated AC 230 V, max. 1000 W with parallel compensation Capacitive load: AC 230 V, max. 105 ?F Device width: 4 modules = approx. 72 mm - Contents: With bus connecting terminal and cable cover.
5276
649208 SWITCH ACTUATOR REG-K/8X230/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
5277 649202 Switch actuator REG-K/2x230/10 with manual mode ACTUATORS - OUTPUTS
Switch actuator REG-K/2x230/10 with manual mode For independent switching of up to 2 loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-button operation. With integrated bus coupler. For installation on DIN rails EN 50022. Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. KNX software functions: Operation as break contact/make contact. Programmable behaviour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel. Power supply: Nominal voltage: AC 230 V, 50-60 Hz For each switch output: Nominal current: 10 A, cos?? = 1; 10 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 2000 W Halogen lamps: AC 230 V, max. 1700 W Fluorescent lamps: AC 230 V, max. 1800 W, uncompensated AC 230 V, max. 1000 W with parallel compensation Capacitive load: AC 230 V, max. 105 ?F Device width: 2.5 modules = approx. 45 mm
5277
649202 SWITCH ACTUATOR REG-K/2X230/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
5278 649204 Switch actuator REG-K/4x230/10 with manual mode ACTUATORS - OUTPUTS
Switch actuator REG-K/4x230/10 with manual mode For independent switching of up to 4 loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-button operation. With integrated bus coupler. For installation on DIN rails EN 50022. Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. KNX software functions: Operation as break contact/make contact. Programmable behaviour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel. Power supply: Nominal voltage: AC 230 V, 50-60 Hz For each switch output: Nominal current: 10 A, cos?? = 1; 10 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 2000 W Halogen lamps: AC 230 V, max. 1700 W Fluorescent lamps: AC 230 V, max. 1800 W, uncompensated AC 230 V, max. 1000 W with parallel compensation Capacitive load: AC 230 V, max. 105
5278
649204 SWITCH ACTUATOR REG-K/4X230/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
5279 649212 Switch actuator REG-K/12x230/ 10 with manual mode ACTUATORS - OUTPUTS
Switch actuator REG-K/12x230/ 10 with manual mode For independent switching of up to 12 loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-button operation. With integrated bus coupler. For installation on DIN rails EN 50022. Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. KNX software functions: Operation as break contact/make contact. Programmable behaviour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel. Power supply: Nominal voltage: AC 230 V, 50-60 Hz External auxiliary voltage: AC 110-240 V, 50- 60 Hz, max. 2 VA For each switch output: Nominal current: 10 A, cos?? = 1; 10 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 2000 W Halogen lamps: AC 230 V, max. 1700 W Fluorescent lamps: AC 230 V, max. 1800 W, uncompensated AC 230 V, max. 1000 W with parallel compensation Capacitive load: AC 230 V, max. 105 ?F Device width: 6 modules = approx. 108 mm
5279
649212 SWITCH ACTUATOR REG-K/12X230/ 10 WITH MANUAL MODE ACTUATORS - OUTPUTS
5280 646704 Blind actuator REG-K/4x/6 ACTUATORS - OUTPUTS
Blind actuator REG-K/4x/6 For independent control of 4 blind/roller shutter drives. With integrated bus coupler and plug-in screw terminals. For installation onto DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded. KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Weather alarms. 8-bit positioning for height and slats. Scenes. Automatic function. Differentiated status and feedback functions. For each blind output: Nominal voltage: AC 230 V, 50-60 Hz Nominal current: 6 A, cos?? = 0.6 Motor load: AC 230 V, max. 1000 W Device width: 4 modules = approx. 72 mm
5280
646704 BLIND ACTUATOR REG-K/4X/6 ACTUATORS - OUTPUTS
5283 649704 Roller shutter actuator REG-K/4x/10 with manual mode ACTUATORS - OUTPUTS
For independent control of 4 roller shutter drives. The function of the roller shutter channels is freely configurable. All roller shutter outputs can be operated manually using push-button operation. With integrated bus coupler. For installation onto DIN rails EN 50022. Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. KNX software functions: Roller shutter functions: Running time. Idle time. Differentiated disable functions and weather alarms. 8-bit positioning for height. Scenes. Manual/ automatic function. Differentiated status and status feedback functions. For each roller shutter output: Nominal voltage: AC 230 V, 50-60 Hz Nominal current: 10 A, cos?? = 0.6 Motor load: AC 230 V, max. 1000 W Device width: 4 modules = approx. 72 mm Contents: With bus connecting terminal and cable cover.
5283
649704 ROLLER SHUTTER ACTUATOR REG-K/4X/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
5305 648704 Blind actuator REG-K/4x24/6 with manual mode ACTUATORS - OUTPUTS
Blind actuator REG-K/4x24/6 with manual mode For independent control of 4 blind/roller shutter drives. The function of the blind channels is freely configurable. All blind outputs can be operated manually using push-button operation. With integrated bus coupler. For installation onto DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation. KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Differentiated disable functions and weather alarms. 8-bit positioning for height and slat. Scenes. Manual/automatic mode. Differentiated status and status feedback functions. For each blind output: Nominal voltage: DC 24 V ±10 % Nominal current: 6 A Load types: 24 V direct current drives Device width: 4 modules = approx. 72 mm
5305
648704 BLIND ACTUATOR REG-K/4X24/6 WITH MANUAL MODE ACTUATORS - OUTPUTS
5363 649908 Blind/switch actuator REG-K/8x/16x/10 m. ACTUATORS - OUTPUTS
For independent control of up to 8 blind/roller
shutter drives or for switching up to 16 loads via
make contacts. The function of the blind or switching
channels is freely configurable. All blind/switch
outputs can be operated manually using push-buttons.
With integrated bus coupling unit. For installation
on DIN rails EN 50022.

The bus is connected using a bus connecting terminal;
a data rail is not necessary. Channel status
display via LEDs. A green LED indicates readiness
for operation.

KNX software functions:
Blind functions: Blind type. Running time. Idle
time. Step interval. Weather alarm. 8-bit positioning
for height and slats. Scenes. Status and feedback
function.
Switch actuator functions: Operation as break
contact/make contact. Programmable behaviour
for download. Delay functions for each channel.
Staircase lighting function with/without manual
OFF function. Cut-out warning for staircase lighting
function. Scenes. Central function. Disable function.
Logic operation or priority control. Status
feedback function for each channel.

Power supply:
Nominal voltage: AC 230 V, 50-60 Hz
External auxiliary voltage: AC 110-240 V, 50-
60 Hz, max. 2 VA
For each blind output:
Nominal current:10 A, cos?? = 0.6
Motor load: AC 230 V, max. 1000 W
For each switch output:
Nominal current: 10 A, cos?? = 1; 10 A, cos?? = 0.6
Incandescent lamps: AC 230 V, max. 2000 W
Halogen lamps: AC 230 V, max. 1700 W
Fluorescent lamps:
AC 230 V, max. 1800 W, uncompensated
AC 230 V, max. 1000 W with parallel compensation
Capacitive load: AC 230 V, max. 105 µF
Device width: 8 modules = approx. 144 mm

Note: The blind actuator/switch actuator cannot be used in conjunction
with the weather-dependent automatic functions of the
weather combi-sensor/DCF77 art. no. 663692. If you require these
functions then use the blind actuators art. no. 6498...

Contents: With bus connecting terminal and cable cover.
5363
649908 BLIND/SWITCH ACTUATOR REG-K/8X/16X/10 M. ACTUATORS - OUTPUTS
5364 649912 Blind / switch actuator REG-K/ 12x/24x/10 with manual mode ACTUATORS - OUTPUTS
For independent control of up to 12 blind/roller
shutter drives or for switching up to 24 loads via
make contacts. The function of the blind or switching
channels is freely configurable. All blind/switch
outputs can be operated manually using push-buttons.
With integrated bus coupler. For installation
on DIN rails EN 50022.

The bus is connected using a bus connecting terminal;
a data rail is not necessary. Channel status
display via LEDs. A green LED indicates readiness
for operation.

KNX software functions:
Blind functions: Blind type. Running time. Idle
time. Step interval. Weather alarm. 8-bit positioning
for height and slats. Scenes. Status and feedback
function.
Switch actuator functions: Operation as break
contact/make contact. Programmable behaviour
for download. Delay functions for each channel.
Staircase lighting function with/without manual
OFF function. Cut-out warning for staircase lighting
function. Scenes. Central function. Disable function.
Logic operation or priority control. Status
feedback function for each channel.

Power supply:
Nominal voltage: AC 230 V, 50-60 Hz
External auxiliary voltage: AC 110-240 V, 50-
60 Hz, max. 2 VA
For each blind output:
Nominal current: 10 A, cos?? = 0.6
Motor load: AC 230 V, max. 1000 W
For each switch output:
Nominal current: 10 A, cos?? = 1; 10 A, cos?? = 0.6
Incandescent lamps: AC 230 V, max. 2000 W
Halogen lamps: AC 230 V, max. 1700 W
Fluorescent lamps:
AC 230 V, max. 1800 W, uncompensated
AC 230 V, max. 1000 W parallel-compensated
Capacitive load: AC 230 V, max. 105 ?F
Device width: 12 TE = approx. 216 mm
5364
649912 BLIND / SWITCH ACTUATOR REG-K/ 12X/24X/10 WITH MANUAL MODE ACTUATORS - OUTPUTS
5369 649350 Universal dimming actuator REG-K/230/500 W ACTUATORS - OUTPUTS
Universal dimming actuator REG-K/230/500 W AC 230 V, 50-60 Hz For switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, shortcircuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN 50022. The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of inductive and capacitive loads cannot be connected. Bus connection is via bus terminals, a data rail is not necessary. KNX software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/ without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery. Nominal voltage: AC 220 - 230 V, 50/60 Hz Nominal power/channel: max. 500 W/VA 20 W minimum load (ohmic) 50 VA minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC 230 V, 50/ 60 Hz (same phase as the dimming channel) Device width: 4 modules = approx. 72 mm
5369
649350 UNIVERSAL DIMMING ACTUATOR REG-K/230/500 W ACTUATORS - OUTPUTS
5545 680204 Coupler REG-K SYSTEM DEVICES
For logical connection and electrical isolation of lines and areas. For mounting on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. Contact established with the primary and secondary line via bus connecting terminal. Device width: 2 modules = approx. 36 mm - Contents: With 2 bus connecting terminals.
5545
680204 COUPLER REG-K SYSTEM DEVICES
5549 647593 Switch actuator REG-K/4x230/16 with manual mode ACTUATORS - OUTPUTS
For independent switching of four loads via make contacts. With integrated bus coupler 2 and screw terminals. For installation on DIN rails EN 50022. The 230 V switch output can be operated with a manual switch. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded. KNX software functions: Operation as break or make contact, delay functions for each channel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus voltage failure and recovery, parameterisable download behaviour. Nominal voltage: AC 230 V, 50-60 Hz For each switching contact: Nominal current: 16 A, cos?? = 0,6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA Capacitive load: AC 230 V, 16 A, max. 200 ?F Device width: 4 TE = approx. 72 mm
5549
647593 SWITCH ACTUATOR REG-K/4X230/16 WITH MANUAL MODE ACTUATORS - OUTPUTS
5560 628444 Push-button 4-gang plus with IR white GATEWAYS
For System Design. With integrated bus coupling unit. Push-button with eight operating buttons, operating display, eight blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The functions of each of the keys can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Merten IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught to the pushbuttons. The device is connected to the bus line with a bus connecting terminal. KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. ~ Accessories: Labelling sheets for push-button plus art. no. 617819. Transmitter: IR remote control Distance, art. no. 570222. - Contents: With protective hood for plaster. With bus connecting terminal.
5560
628444 PUSH-BUTTON 4-GANG PLUS WITH IR WHITE GATEWAYS
5564 628244 Push-button 3-gang plus white PUSH BUTTONS
Im Design System Fläche. Mit integriertem Busankoppler. Taster mit 6 Bedientasten, Betriebsanzeige, 6 separat ansteuerbaren blauen Statusanzeigen und Schriftfeld. Die blaue Betriebsanzeige kann auch als Orientierungslicht verwendet werden. Der untere Schriftfeldbereich ist als zustzliche Bedientaste parametrierbar. Die Tasten sind als Tastenpaar (zweiflächig) oder als Einzeltasten frei parametrierbar. Das Gerät wird übereine Busanschlussklemme mit der Busleitung verbunden. Softwarefunktionen KNX: Schalten, Umschalten, Dimmen (ein- /zweiflächig), Jalousie (ein- /zweiflächig), Flanken lst 1,- 2-, 4- oder 8-Bit-Telegramme aus (Unterscheidung kurze/lange Betätigung), Flanken mit 2-Byte-Telegrammen (Unterscheidung kurze/lange Betätigung), 8-Bit-Schieberegler, Szenenabruf, Szenenspeicherung, Sperrfunktionen. Zubehr: Beschriftungsbogen für Taster plus Art.-Nr. 617819. Material: Thermoplast brillant Ausführung: wei Fabrikat: Merten Art.-Nr.: 628244 oder gleichwertig
5564
628244 PUSH-BUTTON 3-GANG PLUS WHITE PUSH BUTTONS
5568 628044 Push-button, 1-gang plus white PUSH BUTTONS
For System Design. With integrated bus coupling unit. Push-button with two operating buttons, operating display, two blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. ~ Accessories: Labelling sheets for push-button plus art. no. 617819. - Contents: With protective hood for plaster. With bus connecting terminal.
5568
628044 PUSH-BUTTON, 1-GANG PLUS WHITE PUSH BUTTONS
5572 628144 Push-button 2-gang plus white PUSH BUTTONS
Push-button, 2-gang plus For System Design. With integrated bus coupling unit. Push-button with four operating buttons, operating display, four blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. ~ Accessories: Labelling sheets for push-button plus art. no. 617819. - Contents: With protective hood for plaster. With bus connecting terminal.
5572
628144 PUSH-BUTTON 2-GANG PLUS WHITE PUSH BUTTONS
5576 628344 Push-button 4-gang plus white PUSH BUTTONS
For System Design. With integrated bus coupling unit. Push-button with eight operating buttons, operating display, eight blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. ~ Accessories: Labelling sheets for push-button plus art. no. 617819. - Contents: With protective hood for plaster. With bus connecting terminal.
5576
628344 PUSH-BUTTON 4-GANG PLUS WHITE PUSH BUTTONS
8478 630919 KNX ARGUS Presence with light control and IR receiver DETECTORS
Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are transmitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightnessdependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS. Light control enables the required brightness in a room to be achieved permanently. Dimming and the optional use of a second lighting group maintains a constant brightness. Individual ARGUS Presence configurations can be changed or other KNX devices can be controlled remotely using the IR receiver. With integrated bus coupling unit. For ceiling mounting in a size 60 mounting box, optimal installation at 2.5 m. Can also be mounted to ceilings using the surface mounting housing for ARGUS Presence. KNX software functions: · Five movement/presence blocks: up to four functions · can be triggered per block. Telegrams: 1 bit, 1 byte, 2 bytes. · An additional light control block: brightness can be maintained constant by dimming and an additional · adjustable level. · IR receiver function. IR configuration: setting the brightness threshold, staircase timer factors or range. · Normal operation, master, slave, monitoring, safety pause, disable function. Four movement sensors: the sensitivity and range can be set separately for each sensor. Self-adjusting staircase timer. Actual brightness value: can be detected via the internal and/or an external light sensor. Actual value correction. Angle of detection: 360° Range: a radius of max. 7 m (at a mounting height of 2.50 m) Number of levels: 6 Number of zones: 136 with 544 switching segments Number of movement sensors: 4, separately adjustable Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX Number of IR channels: 10 for controlling KNX devices, 10 for configuration EC Directives: Low-voltage guideline 73/23/EEC and EMC guideline 89/336/EEC
8478
630919 KNX ARGUS PRESENCE WITH LIGHT CONTROL AND IR RECEIVER DETECTORS
8611 663990 KNX Basic weather station. polar white SENSORS
This universal weather station with direct bus connection provides the KNX system with all the relevant weather data. Wind, rain, brightness and temperature - the KNX Basic weather station records all weather data in one device. The incoming data can be used individually or in various combinations and dependencies. There are seven different channels with threshold values that can be configured separately for this purpose. Four universal channels permit any combination of measured values. The three so-called ``sunshade channels`` are optimised specifically for awning, blind and roller shutter applications. In addition there is a ``sunshade automatic`` feature which allows blinds and awnings to be controlled inde-pendently and directly, without manual adjustment. The blinds are automatically adjusted according to the brightness, for instance, so as to provide comfortable lighting conditions at all times. The recorded weather data is evaluated in the device itself and transmitted to the KNX system. The measured data for wind, brightness and temperature are transmitted as a 2-byte value, while rain is sent as 1-bit information. All the sensors including the electronics are combined in one compact device. In order to avoid measuring faults, e.g. as a result of dew, the rain sensor is dried by an integrated heating system (230 V) as required. Even when it comes to installation, the KNX Basic weather station boasts great versatility. The device is easy to mount to a pole, a ceiling or the corner of a building.
8611
663990 KNX BASIC WEATHER STATION. POLAR WHITE SENSORS
8867 630644 KNX ARGUS Presence 180/2.20 m flushmounted DETECTORS
The ARGUS Presence 180/2.20 m UP (referred to below as ARGUS) is a flush-mounted KNX presence detector for indoor installation. It detects moving heat sources, e.g. people, within a radius of 180° and to a distance of approx. 8 m to the right and left and approx.12 m to the front. The ARGUS is designed for installation at a height of 2.2 m. A mounting height of 1.1 m is also possible, although this will halve the range. With anti-crawl protection, movement directly beneath the device is also detected.
8867
630644 KNX ARGUS PRESENCE 180/2.20 M FLUSHMOUNTED DETECTORS
9016 616844 Room temperature control unit FM with 4-gang push-button interface CLIMATE CONTROL
Proper use - Individual room temperature control in KNX installations - Flush mounting in cavity walls or in solid walls. Product properties - Measurement of room temperature and comparison with temperature setpoint - Specification of setpoint by selection of operating mode - Operating modes comfort, standby, night economy, frost/heat protection - Heating and cooling - Heating and cooling with base and additional levels - Adjusting wheel for setpoint correction - Presence key - Status LED - Push-button interface with four inputs or two outputs, for example, for window contacts, pushbuttons, LEDs, etc. - Functions of the inputs: switching, dimming, blinds control, light scene extension unit, brightness or temperature valuator - Optional: external temperature sensor for room temperature measurement (art. no. 616790)
9016
616844 ROOM TEMPERATURE CONTROL UNIT FM WITH 4-GANG PUSH-BUTTON INTERFACE CLIMATE CONTROL
9023 616944 Room temperature control unit FM with 4-gang push-button interface CLIMATE CONTROL
Proper use - Individual room temperature control in KNX installations - Flush mounting in cavity walls or in solid walls. Product properties - Measurement of room temperature and comparison with temperature setpoint - Specification of setpoint by selection of operating mode - Operating modes comfort, standby, night economy, frost/heat protection - Heating and cooling - Heating and cooling with base and additional levels - Adjusting wheel for setpoint correction - Presence key - Status LED - Push-button interface with four inputs or two outputs, for example, for window contacts, pushbuttons, LEDs, etc. - Functions of the inputs: switching, dimming, blinds control, light scene extension unit, brightness or temperature valuator - Optional: external temperature sensor for room temperature measurement (art. no. 616790)
9023
616944 ROOM TEMPERATURE CONTROL UNIT FM WITH 4-GANG PUSH-BUTTON INTERFACE CLIMATE CONTROL
9028 644492 Binary input REG-K/4x10 INPUTS
The binary input REG-K/4x10 has four inputs and is used for connecting four conventional push-buttons or floating contacts such as window or relay contacts. The device makes a contact supply voltage (SELV) available which is electrically isolated from the bus voltage. A separate power supply is not required. The function of the channels is determined by the loaded application software.
9028
644492 BINARY INPUT REG-K/4X10 INPUTS
9029 644592 Binary input REG-K/8x10 INPUTS
The Merten binary input REG-K/8x10 is used to connect floating contacts, push-buttons or switches to the EIB.
9029
644592 BINARY INPUT REG-K/8X10 INPUTS
9030 644892 Binary input REG-K/4x24 INPUTS
The Merten binary input REG-K/4x24 is used to connect conventional 24 V devices (such as door and window contacts) to the KNX bus.
9030
644892 BINARY INPUT REG-K/4X24 INPUTS
9031 644992 Binary input REG-K/4x230 INPUTS
The Merten binary input REG-K/4x230 is used to connect conventional 230 V devices (such as movement detectors and light-sensitive switches) to the KNX bus..
9031
644992 BINARY INPUT REG-K/4X230 INPUTS
9033 632644 KNX ARGUS 180, flush-mounted DETECTORS
The ARGUS 180 flush-mounted (referred to below as ARGUS) is a flush-mounted KNX movement detector for indoor installation. It detects moving heat sources, e.g. people, within a radius of 180° and up to a distance of approx. 8 m. The ARGUS is designed for installation at a height of 1.1 m. The movement detector will not switch the lighting on until it detects movement in front of the device when the ambient brightness is too low. If movement is no longer detected in the activated state, the integrated staircase timer will switch the lighting back off. The ETS application includes 5 independent movement blocks, each with 4 output objects.
9033
632644 KNX ARGUS 180, FLUSH-MOUNTED DETECTORS
9079 631844 KNX ARGUS 180, flush-mounted DETECTORS
KNX ARGUS 180, flush-mounted For System Design. Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted. With integrated bus coupling unit. KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: 1 bit, 1 byte, 2 bytes. Normal operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Self-adjusting staircase timer. Angle of detection: 180° Range: 8 m (for mounting height of 1.1 m) Number of levels: 1 Number of zones: 14 Sensitivity: infinitely adjustable (ETS or potentiometer) Light sensor: infinitely adjustable from approx. 10 to 2000 Lux (ETS or potentiometer) Time: adjustable in steps from 1 s to 8 min (potentiometer) or adjustable from 1 s to 255 hours (ETS) EC Directives: Low-voltage guideline 73/23/EEC and EMC guideline 89/336/EEC - Contents: With bus connecting terminal and supporting plate.
9079
631844 KNX ARGUS 180, FLUSH-MOUNTED DETECTORS
9082 632744 KNX ARGUS 180/2.20m UP, SYSTEM M DETECTORS
KNX ARGUS 180/2.20 m flushmounted For System M. Indoor movement detector with anti-crawl protection. When a movement is detected, a data telegram defined by the programming is transmitted. With integrated bus coupling unit. For wall mounting in a size 60 mounting box, optimal installation at 2.2 m. KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: 1 bit, 1 byte, 2 bytes. Normal operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-adjusting staircase timer. Angle of detection: 180° Range: 8 m right/left, 12 m to the front (for a mounting height of 2.20 m) Mounting height: 2.2 m or 1.1 m with half the range Number of levels: 6 Number of zones: 46 Number of movement sensors: 2, sector-orientated, adjustable Sensitivity: infinitely adjustable (ETS or potentiometer) Light sensor: infinitely adjustable from approx. 10 to 2000 Lux (ETS or potentiometer) Time: adjustable in steps from 1 s to 8 min (potentiometer) or adjustable from 1 s to 255 hours (ETS) EC Directives: Low-voltage guideline 73/23/EEC and EMC guideline 89/336/EEC - Contents: With bus connecting terminal and supporting plate. With cover segments to limit the area of detection
9082
632744 KNX ARGUS 180/2.20M UP, SYSTEM M DETECTORS
9087 632519 ARGUS 220 - KNX movement detector DETECTORS
The ARGUS 220 is a KNX movement detector which can be used both indoors and outdoors due to its IP 55 protection rating. Surface monitoring of 220° for larger house fronts and areas of the house (max. range of 16 m) is combined with a 360° short-range zone with a radius of approx. 4 m. The operating elements for setting the brightness, time and sensitivity (range) as well as the programming area and a red LED for displaying the programming are located under the cover plate for protection. The physical address is programmed using a programming magnet (e.g. art. no. 639190). The ARGUS can be mounted on the wall or ceiling and also on to corners or fixed pipes with the mounting bracket (art. no. 5652 ..) which is available as an accessory. The integrated functional display lights up when movement is detected and thus simplifies the alignment of the device at the installation site. You can also optionally switch off the functional display via a parameter setting. The area of detection can be adapted to the local conditions due to the horizontally, vertically and axially adjustable sensor head. You can also block unwanted zones or sources of interference (e.g. trees) from the area of detection using the masking segments provided. The device is fitted with a light sensor whose brightness threshold can be set from approx. 3 to 1000 lux. Depending on the application, it is also possible to use the device as a light-sensitive switch or to link the brightness threshold with the detection of movement. Several movement detectors can be combined together in a system. The power is supplied via the bus line. No additional mains connection is required. As the bus line is connected directly to the terminal block in the wall connection box, a bus connecting terminal is not required.
9087
632519 ARGUS 220 - KNX MOVEMENT DETECTOR DETECTORS
9128 630719 KNX ARGUS Presence Basic DETECTORS
Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are transmitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightnessdependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS. With integrated bus coupling unit. For ceiling mounting in a size 60 mounting box, optimal installation at 2.5 m. Can also be mounted to ceilings using the surface mounting housing for ARGUS Presence. KNX software functions: Two movement/presence blocks: up to four functions can be triggered per block. Telegrams: 1 bit, 1 byte, 2 bytes. Normal operation (no master/slave), safety pause, disable function. Self-adjusting staircase timer. Actual brightness value: can be specified via the internal and/or an external light sensor. Angle of detection: 360° Range: a radius of max. 7 m (at a mounting height of 2.50 m) Number of levels: 6 Number of zones: 136 with 544 switching segments Number of movement sensors: 4 Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX EC Directives: Low-voltage guideline 73/23/EEC and EMC guideline 89/336/EEC ~ Accessories: Surface-mounted housing for ARGUS Presence, art. no. 550619. - Contents: With bus connecting terminal and supporting plate.
9128
630719 KNX ARGUS PRESENCE BASIC DETECTORS
9130 630819 KNX ARGUS Presence Basic DETECTORS
KNX ARGUS Presence Basic Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are transmitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightnessdependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS. With integrated bus coupling unit. For ceiling mounting in a size 60 mounting box, optimal installation at 2.5 m. Can also be mounted to ceilings using the surface mounting housing for ARGUS Presence. KNX software functions: Two movement/presence blocks: up to four functions can be triggered per block. Telegrams: 1 bit, 1 byte, 2 bytes. Normal operation (no master/slave), safety pause, disable function. Self-adjusting staircase timer. Actual brightness value: can be specified via the internal and/or an external light sensor. Angle of detection: 360° Range: a radius of max. 7 m (at a mounting height of 2.50 m) Number of levels: 6 Number of zones: 136 with 544 switching segments Number of movement sensors: 4 Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX EC Directives: Low-voltage guideline 73/23/EEC and EMC guideline 89/336/EEC ~ Accessories: Surface-mounted housing for ARGUS Presence, art. no. 550619. - Contents: With bus connecting terminal and supporting plate.
9130
630819 KNX ARGUS PRESENCE BASIC DETECTORS
9134 663991 KNX brightness and temperature sensor SENSORS
The weather station measures temperature and brightness. The measured values can be sent to the bus. The sensor has 2 different channel types: • 4 universal channels • 1 sun protection channel The universal channels can be used for sub-tasks (e.g. only brightness threshold) or for a combination of brightness and temperature. A channel is made up of up to 2 logically linked weather conditions: • If the brightness is above/below the threshold AND • If the temperature is above/below the threshold AND A non-relevant condition (e.g. temperature) can be set to the value "any" and is then ignored in logical linking. As a result of the satisfaction or non-satisfaction of this AND link, a telegram is sent to the associated channel object (e.g. channel 1.1). If required, an additional second object (e.g. channel 1.2) can be activated and thus send another telegram. Each universal channel has one lock object and one teach in object for the brightness threshold.
9134
663991 KNX BRIGHTNESS AND TEMPERATURE SENSOR SENSORS
9209 677290 KNX Time sender REG-K TIME TRANSMITTERS - SWITCHES
The time sender sends time and date on the KNX bus and can be operated with or without a DCF antenna. The time sender is set in the factory to time and date. Toggling summer time/winter time – Switching between summer time and winter time takes place on the basis of the quartz time and the changover rule specified. – The rule for Central European summer time and winter time is preprogrammed in the factory. This can be changed in the application. – If no DCF signal is received, summer time and winter time will be calculated automatically.
9209
677290 KNX TIME SENDER REG-K TIME TRANSMITTERS ...
9220 684016 KNX power supply unit REG-K/160 mA SYSTEM DEVICES
The KNX power supply REG-K (referred to below as the power supply) is connected to a bus system and makes the energy available for the bus devices on a line. At least one power supply is required per bus line. The power supply unit has an integrated choke which isolates the data telegrams from the power supply. The power supply unit provides a stabilised safety extra low voltage (SELV) of DC 30 V. It is short-circuit resistant, and features a voltage and current limiter. Excessively high output currents are indicated by a red display (overcurrent). The max. cable length between the power supply and the furthest bus device is 350 m. The bus devices on the connected line can be reset using a button on the power supply. The state (RESET) is indicated by the red display (RESET) on the device. The green display (RUN) indicates that the power supply is ready for operation. The power supply is to be installed in the DIN rail as per DIN EN 60715. A data rail is not required.
9220
684016 KNX POWER SUPPLY UNIT REG-K/160 MA SYSTEM DEVICES
9221 684032 KNX power supply unit REG-K/320 mA SYSTEM DEVICES
The KNX power supply REG-K (referred to below as the power supply) is connected to a bus system and makes the energy available for the bus devices on a line. At least one power supply is required per bus line. The power supply unit has an integrated choke which isolates the data telegrams from the power supply. The power supply unit provides a stabilised safety extra low voltage (SELV) of DC 30 V. It is short-circuit resistant, and features a voltage and current limiter. Excessively high output currents are indicated by a red display (overcurrent). The max. cable length between the power supply and the furthest bus device is 350 m. The bus devices on the connected line can be reset using a button on the power supply. The state (RESET) is indicated by the red display (RESET) on the device. The green display (RUN) indicates that the power supply is ready for operation. The power supply is to be installed in the DIN rail as per DIN EN 60715. A data rail is not required.
9221
684032 KNX POWER SUPPLY UNIT REG-K/320 MA SYSTEM DEVICES
9222 684064 KNX power supply unit REG-K/640 mA SYSTEM DEVICES
The KNX power supply REG-K (referred to below as the power supply) is connected to a bus system and makes the energy available for the bus devices on a line. At least one power supply is required per bus line. The power supply unit has an integrated choke which isolates the data telegrams from the power supply. The power supply unit provides a stabilised safety extra low voltage (SELV) of DC 30 V. It is short-circuit resistant, and features a voltage and current limiter. Excessively high output currents are indicated by a red display (overcurrent). The max. cable length between the power supply and the furthest bus device is 350 m. The bus devices on the connected line can be reset using a button on the power supply. The state (RESET) is indicated by the red display (RESET) on the device. The green display (RUN) indicates that the power supply is ready for operation. The power supply is to be installed in the DIN rail as per DIN EN 60715. A data rail is not required.
9222
684064 KNX POWER SUPPLY UNIT REG-K/640 MA SYSTEM DEVICES
9225 683816 KNX power supply unit REG-K/160 mA with emergency power input SYSTEM DEVICES
The KNX power supply REG-K is connected to a bus system and makes the energy available for the bus devices on a line. At least one power supply is required per bus line. The power supply unit has an integrated choke which isolates the data telegrams from the power supply. The power supply unit provides a stabilised safety extralow voltage (SELV) of DC 30 V. It is short-circuit resistant, and features a voltage and current limiter. Excessively high output currents are indicated by a red display (overcurrent). The max. cable length between the power supply and the furthest bus device is 350 m. The bus devices on the connected line can be reset using a button on the power supply. The state (RESET) is indicated by the red display (RESET) on the device. The green display (RUN) indicates that the power supply is ready for operation. The power supply is to be installed in the DIN rail as per DIN EN 60715. A data rail is not required.
9225
683816 KNX POWER SUPPLY UNIT REG-K/160 MA WITH EMERGENCY POWER INPUT SYSTEM DEVICES
9226 683832 KNX power supply unit REG-K/320 mA with emergency power input SYSTEM DEVICES
The KNX power supply REG-K is connected to a bus system and makes the energy available for the bus devices on a line. At least one power supply is required per bus line. The power supply unit has an integrated choke which isolates the data telegrams from the power supply. The power supply unit provides a stabilised safety extralow voltage (SELV) of DC 30 V. It is short-circuit resistant, and features a voltage and current limiter. Excessively high output currents are indicated by a red display (overcurrent). The max. cable length between the power supply and the furthest bus device is 350 m. The bus devices on the connected line can be reset using a button on the power supply. The state (RESET) is indicated by the red display (RESET) on the device. The green display (RUN) indicates that the power supply is ready for operation. The power supply is to be installed in the DIN rail as per DIN EN 60715. A data rail is not required.
9226
683832 KNX POWER SUPPLY UNIT REG-K/320 MA WITH EMERGENCY POWER INPUT SYSTEM DEVICES
9227 683890 KNX power supply unit REG-K/640 mA with emergency power input SYSTEM DEVICES
The KNX power supply REG-K is connected to a bus system and makes the energy available for the bus devices on a line. At least one power supply is required per bus line. The power supply unit has an integrated choke which isolates the data telegrams from the power supply. The power supply unit provides a stabilised safety extralow voltage (SELV) of DC 30 V. It is short-circuit resistant, and features a voltage and current limiter. Excessively high output currents are indicated by a red display (overcurrent). The max. cable length between the power supply and the furthest bus device is 350 m. The bus devices on the connected line can be reset using a button on the power supply. The state (RESET) is indicated by the red display (RESET) on the device. The green display (RUN) indicates that the power supply is ready for operation. The power supply is to be installed in the DIN rail as per DIN EN 60715. A data rail is not required.
9227
683890 KNX POWER SUPPLY UNIT REG-K/640 MA WITH EMERGENCY POWER INPUT SYSTEM DEVICES
9231 683901 REG emergency power supply SYSTEM DEVICES
To buffer the bus voltage. If a complete mains failure occurs, an external lead gel battery with a voltage of DC 12 V (SELV) can be connected to the REG power supply for buffering. The lead gel battery is recharged or maintained in its charged state by integrated charging electronics. A binary input can be connected in order to register the operational statuses (mains voltage, error warning, battery operation). For installation on DIN rails EN 60715. A data rail is not necessary. Mains voltage: AC 110 - 230 V, 50-60 Hz Output to power supply: Output voltage: DC 30 V ±2 V Output current: without battery with mains supply max. 300 mA, with battery without mains supply max. 640 mA Short-circuit current: < 1.5 A Charging current: max. 1 A Connections: plug-in screw terminal for main connector, operating state (4-pin, 3 floating contacts) and emergency power supply. Plug-in terminal for battery connection (two 1 mm pins) Device width: 4 TE = approx. 72 mm In KNX, to be completed with: KNX power supply REG-K/160 mA with emergency power input, art. no. 683816. KNX power supply REG-K/320 mA with emergency power input, art. no. 683832. KNX power supply REG-K/640 mA with emergency power input, art. no. 683890. Accessories: Lead gel battery, art. no. 668990. Lead gel battery, art. no. 668991. Binary input REG-K/4x10 art. no. 644492. Binary input REG-K/8x10, art. no. 644592. Contents: With connecting terminal and cable cover
9231
683901 REG EMERGENCY POWER SUPPLY SYSTEM DEVICES
9233 680329 KNX IP-Router REG-K SYSTEM DEVICES
The KNX/IP router enables telegrams to be forwarded between different lines via LAN (IP) as a rapid backbone. The device can additionally serve as a programming interface in order to connect a PC with the KNX bus (e.g. for ETS programming with suitable ETS). The IP address can be assigned dynamically via a DHCP server or via manual configuration (ETS parameter). The device operates in accordance with the KNXnet/IP specification using Core, device management, tunnelling and routing. The KNX/IP router forwards telegrams in both directions whilst taking a filter table into account and can buffer up to 150 telegrams. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. Supply voltage: DC 12-30 V (at DC 24 V 40 mA), AC 12-24 V Device width: 2 modules = approx. 36 mm In KNX, to be completed with: Power supply REG, DC 24 V/0.4 A, art. no. 693003. Power supply REG, DC 24 V/1.25 A, art. no. 693004. Power supply REG, AC 24 V / 1 A, art. no. 663529. Also alternatively Power over Ethernet (PoE). Contents: With bus connecting terminal.
9233
680329 KNX IP-ROUTER REG-K SYSTEM DEVICES
9235 647395 Switch actuator REG-K/2x230/ 16 with manual mode and current detection ACTUATORS - OUTPUTS
For independent switching of two loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All 230 V switch outputs can be operated with manual switches. With integrated bus coupling unit. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals. KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function. Nominal voltage: AC 230 V, 50 - 60 Hz Per switching contact: Nominal current: 16 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA, with parallel compensation Capacitive load: AC 230 V, 16 A, max. 200 µF Motor load: AC 230 V, max. 1000 W Current detection load current: Detection range: 0.1 A to 16 A (sine effective value or DC) Sensing accuracy: +/- 8% of the current value at hand (sine) and +/- 100 mA Frequency: 50/60 Hz Description: 100 mA Device width: 2.5 TE = approx. 45 mm Contents: With bus connecting terminal and cable cover.
9235
647395 SWITCH ACTUATOR REG-K/2X230/ 16 WITH MANUAL MODE AND CURRENT DETECTION ACTUATORS - OUTPUTS
9236 647595 Switch actuator REG-K/4x230/ 16 with manual mode and current detection ACTUATORS - OUTPUTS
For independent switching of four loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All 230 V switch outputs can be operated with manual switches. With integrated bus coupling unit. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals. KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function. Nominal voltage: AC 230 V, 50 - 60 Hz Per switching contact: Nominal current: 16 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA, with parallel compensation Capacitive load: AC 230 V, 16 A, max. 200 µF Motor load: AC 230 V, max. 1000 W Current detection load current: Detection range: 0.1 A to 16 A (sine effective value or DC) Sensing accuracy: +/- 8% of the current value at hand (sine) and +/- 100 mA Frequency: 50/60 Hz Description: 100 mA Device width: 4 TE = approx. 72 mm Contents: With bus connecting terminal and cable cover.
9236
647595 SWITCH ACTUATOR REG-K/4X230/ 16 WITH MANUAL MODE AND CURRENT DETECTION ACTUATORS - OUTPUTS
9237 647895 Switch actuator REG-K/8x230/ 16 with manual mode and current detection ACTUATORS - OUTPUTS
For independently switching 8 loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All 230 V switch outputs can be operated with manual switches. With integrated bus coupling unit. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals. KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function. Nominal voltage: AC 230 V, 50 - 60 Hz Per switching contact: Nominal current: 16 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA, with parallel compensation Capacitive load: AC 230 V, 16 A, max. 200 µF Motor load: AC 230 V, max. 1000 W Current detection load current: Detection range: 0.1 A to 16 A (sine effective value or DC) Sensing accuracy: +/- 8% of the current value at hand (sine) and +/- 100 mA Frequency: 50/60 Hz Description: 100 mA Device width: 8 TE = approx. 144 mm Contents: With bus connecting terminal and cable cover.
9237
647895 SWITCH ACTUATOR REG-K/8X230/ 16 WITH MANUAL MODE AND CURRENT DETECTION ACTUATORS - OUTPUTS
9238 648495 Switch actuator REG-K/12x230/ 16 with manual mode and current detection ACTUATORS - OUTPUTS
For independently switching 12 loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All 230 V switch outputs can be operated with manual switches. With integrated bus coupling unit. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals. KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function. Nominal voltage: AC 230 V, 50 - 60 Hz Per switching contact: Nominal current: 16 A, cos?? = 0.6 Incandescent lamps: AC 230 V, max. 3600 W Halogen lamps: AC 230 V, max. 2500 W Fluorescent lamps: AC 230 V, max. 2500 VA, with parallel compensation Capacitive load: AC 230 V, 16 A, max. 200 µF Motor load: AC 230 V, max. 1000 W Current detection load current: Detection range: 0.1 A to 16 A (sine effective value or DC) Sensing accuracy: +/- 8% of the current value at hand (sine) and +/- 100 mA Frequency: 50/60 Hz Description: 100 mA Device width: 12 TE = approx. 216 mm Contents: With bus connecting terminal and cable cover.
9238
648495 SWITCH ACTUATOR REG-K/12X230/ 16 WITH MANUAL MODE AND CURRENT DETECTION ACTUATORS - OUTPUTS
9268 649310 Universal dimming actuator REG-K/2x230/1000 W AC 230 V, 50-60 Hz ACTUATORS - OUTPUTS
For switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, shortcircuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN 50022. The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of inductive and capacitive loads cannot be connected. Bus connection is via bus terminals, a data rail is not necessary. KNX software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/ without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery. Nominal voltage: AC 220 - 230 V, 50/60 Hz Nominal power/channel: max. 1000 W/VA 20 W minimum load (ohmic) 50 VA minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC 230 V, 50/ 60 Hz (same phase as the dimming channel) Device width: 4 modules = approx. 72 mm Extension unit operation: With mechanical push-buttons (make contact). With extension insert, art. no. 573999, extension TELE insert, art. no. 573998. Contents: With bus connecting terminal and cable cover.
9268
649310 UNIVERSAL DIMMING ACTUATOR REG-K/2X230/1000 W AC 230 V, 50-60 HZ ACTUATORS - OUTPUTS
9269 647091 Control unit 0-10 V REG-K/1-gang with manual mode ACTUATORS - OUTPUTS
For connecting devices with 0-10 V interface to KNX. With integrated bus coupler and screw terminals (230 V) or plug-in screw terminals (0-10 V). The 230 V switch output can be operated with a manual switch. For installation onto DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. KNX software functions: Different dimming curves and dimming speeds, the same dimming time, memory function, ON/ OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery. Switch contact: for switching the electronic ballasts/ transformers Switching voltage: AC 230 V Switching current:16 A, cos?? = 0.6 Switching capacity: AC 230 V, 3600 W, cos?? = 1 Capacitive load: AC 230 V, 3600 W, 200 µF Halogen lamps: AC 230 V, 2500 W Fluorescent lamps: AC 230 V, max. 5000 W, uncompensated AC 230 V, max. 2500 VA, with parallel compensation 0-10 V interface: for dimming the electronic ballasts/ transformers Voltage range: DC 0-10 V Device width: 2.5 TE = approx. 45 mm Contents: With bus connecting terminal and cable cover.
9269
647091 CONTROL UNIT 0-10 V REG-K/1-GANG WITH MANUAL MODE ACTUATORS - OUTPUTS
9270 646991 Control unit 0-10 V REG-K/3-gang with manual mode ACTUATORS - OUTPUTS
For connecting devices with 0-10 V interface to KNX. With integrated bus coupler and screw terminals (230 V) or plug-in screw terminals (0-10 V). Each individual 230 V switch output can be operated manually with a manual switch. For installation onto DIN rails EN 50022. The bus is connected using a bus connecting terminal; a data rail is not necessary. KNX software functions: Different dimming curves and dimming speeds, the same dimming time, memory function, ON/ OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery. Switch contact: for switching the electronic ballasts/ transformers Switching voltage: AC 230 V Switching current:16 A, cos?? = 0.6 Switching capacity: AC 230 V, 3600 W, cos?? = 1 Capacitive load: AC 230 V, 3600 W, 200 µF Halogen lamps: AC 230 V, 2500 W Fluorescent lamps: AC 230 V, max. 5000 W, uncompensated AC 230 V, max. 2500 VA, with parallel compensation 0-10 V interface: for dimming the electronic ballasts/ transformers Voltage range: DC 0-10 V Device width: 4 TE = approx. 72 mm Contents: With bus connecting terminal and cable cover.
9270
646991 CONTROL UNIT 0-10 V REG-K/3-GANG WITH MANUAL MODE ACTUATORS - OUTPUTS
9274 645094 KNX fan coil actuator REG-K CLIMATE CONTROL
For heating, ventilation and air conditioning control. For controlling fan convectors with up to three speeds, as well as for controlling three-step motor drives (continuous/pulse-width-modulated) or two-step thermal drives. The actuator supports 2-pipe and 4-pipe systems. Two floating binary inputs for window contact and level contact for condensed water container, for example. Connection of 1-speed to 3-speed fans. The multi-function push-button with room temperature control from version 3A can be used to activate the fan coil actuator. With integrated bus coupler. For installation on DIN rails EN 60715. The bus is connected using a bus connecting terminal; a data rail is not necessary. KNX software functions: Fan control: In automatic mode, the fan speeds are controlled dependently by the control value of the multi-function push-button. The three fan speeds and automatic mode can be switched via EIB telegram. The fan can be controlled either directly or via actuators / suitable dimming actuators. Fan speed feedback is possible via corresponding status feedback objects e.g. status LED of the push-button. The fan speed as well as the automatic status (Auto)can be displayed on the display of the multi-function push-button with TCU. Valve control: Type of controller: PI controller (PWM and continuous). Controller mode: Heating and/or cooling with common or separate valve outputs. Operating modes: The operating mode is selected in the multi-function push-button with TCU Power supply: AC 230 V ±10 %, 50/60 Hz Power consumption: max. 3 VA Outputs: 3 floating contacts (fan coil), 2 semi-conductor switches (valve connections) Switching capacity for valves: 0.5 A, AC 24V - 230 V Additional relay switching capacity: 16 A Fan relay switching capacity: 8 A Inputs: 2, max. cable length 5 m Operation: Key for fan levels and heating/cooling mode Displays: 9 status LEDs Device width: 4 modules = approx. 72 mm Accessories: Multi-function push-button with room temperature control unit, art. no. 6232.., 6273.. , 6236..,6274.., 6287.., 6288.., 626008. Thermoelectric valve drive 24 V art. no. 639126. Version : light grey
9274
645094 KNX FAN COIL ACTUATOR REG-K CLIMATE CONTROL
16352 MEG6710-0002 KNX universal dimmer, 2x230/300W ACTUATORS - OUTPUTS

 Dimming actuator bus system 4...300W Bus system KNX, Other bus systems None, Model Dimming actuator, Mounting method DRA, Width in number of modular spacings 4, Bus connection included, Local operation/hand operation, With LED indication, Number of outputs 2, Output power 4 ... 300W, Type of load Universal, Voltage 230 ... 230V, Frequency 50 ... 60Hz, Degree of protection (IP) IP20,

16352
MEG6710-0002 KNX UNIVERSAL DIMMER, 2X230/300W ACTUATORS - OUTPUTS
11025 MEG6212-0444 Button panel for bus system, white PUSH BUTTONS
Button panel for bus system Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of actuation points 6, With display, Status-LED, Manual set point setting, Temperature controller, Timer clock, With anti-theft/dismantling protection, Central functional unit for senders/actuators, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour Cream white/electro white, RAL-number (akin) 1013, Degree of protection (IP) IP20, Bus connection included
11025
MEG6212-0444 BUTTON PANEL FOR BUS SYSTEM, WHITE PUSH BUTTONS
12063 676090 KNX Logicmodul Basic CONTROLLERS

Combining different building functions makes many aspects of daily life easier, whether in the office or at home. The new logic module Basic REG-K is a perfect supplement to KNX applications – an optimal logic operation and controlling building functions are made simply possible.

Intelligent control – KNX Logic module Basic REG-K
Thanks to the logic module, special logic operations can be initiated between actuators and sensors creating numerous logic functions for controlled KNX devices. This added value in comfort, security and savings in energy and costs is made possible by the numerous functions that the logic module offers.

The KNX Logic module Basic REG-K offers comfort
Flexible conference rooms with movable walls need a flexible connection between push buttons and switch/dim or blind actuators. That is a typical application for logic module’s multiplexer function.

The KNX Logic module Basic REG-K offers security
Do you want to make sure that you closed all the windows when you left the house? This is easy with the logic module. With this device, all the window contacts are linked and the status of the windows can be clearly shown, for example, on an info display in the corridor.

The KNX Logic module Basic REG-K saves energy, time and money
Supermarkets, for example, do not switch off their lights completely at night. Thanks to the logic module, the lights age at the same rate because a different row of lights is switched on every night. This rotating system saves the service technician time and the operator saves money.

12063
676090 KNX LOGICMODUL BASIC CONTROLLERS
12597 412160 412160 Wippe aluminium PUSH BUTTONS
Merten Schaltersysteme 412160 Wippe aluminium
12597
412160 412160 WIPPE ALUMINIUM PUSH BUTTONS
12720 MEG6600-0603 Energy meter 3x230V/16A SMART METERING
Energy meter for bus system Bus system KNX, Other bus systems None, Model Energy meter, Connection type Direct, S0 impulse interface None, Tariff switch,
12720
MEG6600-0603 ENERGY METER 3X230V/16A SMART METERING
13357 MEG6214-4044 Button panel for bus system 4fold CLIMATE CONTROL
Button panel for bus system Bus system KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of actuation points 10, With display, Status-LED, IR sensor, Manual set point setting, Temperature controller, Timer clock, With anti-theft/dismantling protection, Central functional unit for senders/actuators, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour Cream white/electro white, RAL-number (akin) 1013, Degree of protection (IP) IP20, Bus connection included,
13357
MEG6214-4044 BUTTON PANEL FOR BUS SYSTEM 4FOLD CLIMATE CONTROL
13636 MEG6214-0344 Button panel for bus system, 4 fold CLIMATE CONTROL
utton panel for bus system Bus system KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of actuation points 10, With display, Status-LED, IR sensor, Manual set point setting, Temperature controller, Timer clock, With anti-theft/dismantling protection, Central functional unit for senders/actuators, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Matt, Colour White, RAL-number (akin) 9010, Degree of protection (IP) IP20, Bus connection included,
13636
MEG6214-0344 BUTTON PANEL FOR BUS SYSTEM, 4 FOLD CLIMATE CONTROL
13908 MEG6500-0113 KNX InSideControl IP-Gateway VISUALIZATION
Ethernet Interface for bus system Bus system KNX, Model Ethernet, Width in number of modular spacings 2, Bus connection included, With LED indication, 
13908
MEG6500-0113 KNX INSIDECONTROL IP-GATEWAY VISUALIZATION
15865 MEG6725-0001 KNX DALI-Gateway REG-K/1/16 GATEWAYS

The KNX DALI gateway REG-K/1/16(64)/64/IP1 (referred to below as the gateway) connects the KNX bus with the DALI bus. Lights with DALI ECGs (electronic ballasts) can therefore be integrated into an overall KNX architecture and operated via the multitude of existing KNX devices.

The device transforms switch and dim commands fromthe connected KNX system into DALI telegrams and statusinformation from the DALI bus into KNX telegrams.

ECGs can be switched, dimmed and set to a defined value in 16 groups per gateway. In addition to group control, the gateway offers the possibility to individually control up to 64 ECGs

15865
MEG6725-0001 KNX DALI-GATEWAY REG-K/1/16 GATEWAYS
16150 MEG6501-0001 U.motion KNX Server VISUALIZATION

The U.motion KNX Server/Server Plus is a web-based visualisation system for home and building

automation based on KNX. The server acts as master and allows the control of the KNX devices

through U.motion Client Touches, smartphones, tablet PCs, and any kind of device (PC/MAC) with

a working browser. The remote access to the visualisation is possible with a smartphone, tablet

PCs or any standard computer with a working browser (PC/MAC).

The confi guration and use of this server takes place directly through its web interface, which can

be accessed through a conventional browser. The customisable graphical interface with diff erent

themes is optimised for visualisation on diff erent mobile and fi xed devices. There are various

extension possibilities thanks to functions like scenarios, time scheduling, logics, conditions,

integrators, virtual objects, complexe objects, notifi cations on screen and by e-mail, IP cameras,

as well as support for VoIP integrations (VoIP is only available for the U.motion KNX Server Plus).

The confi guration is possible directly on the server and offl ine via the U.motion Builder (available

for free).

16150
MEG6501-0001 U.MOTION KNX SERVER VISUALIZATION
16151 MEG6501-0002 U.motion KNX Server Plus VISUALIZATION

The U.motion KNX Server/Server Plus is a web-based visualisation system for home and building automation based on KNX. The server acts as master and allows the control of the KNX devices through U.motion Client Touches, smartphones, tablet PCs, and any kind of device (PC/MAC) with a working browser. The remote access to the visualisation is possible with a smartphone, tablet PCs or any standard computer with a working browser (PC/MAC). The confi guration and use of this server takes place directly through its web interface, which can be accessed through a conventional browser. The customisable graphical interface with diff erent themes is optimised for visualisation on diff erent mobile and fi xed devices. There are various extension possibilities thanks to functions like scenarios, time scheduling, logics, conditions, integrators, virtual objects, complexe objects, notifi cations on screen and by e-mail, IP cameras, as well as support for VoIP integrations (VoIP is only available for the U.motion KNX Server Plus). The confi guration is possible directly on the server and offl ine via the U.motion Builder (available for free).

16151
MEG6501-0002 U.MOTION KNX SERVER PLUS VISUALIZATION
16152 MEG6730-0001 Heating actuator 6 channel AC 24V/230V CLIMATE CONTROL

The heating actuator is used for the activation of electrothermal actuators (ETA) for heating orcooling systems. It possesses 6 electronic outputs, each of which can silently activate up to 4(AC 230 V) or 2 (AC 24 V) actuators. Both deenergised closed and deenergised opened actuators can be connected.

16152
MEG6730-0001 HEATING ACTUATOR 6 CHANNEL AC 24V/230V CLIMATE CONTROL
16201 MEG6003-0006 KNX Actuator, Blind- a.Heatingt.FM w.3 Inputs ACTUATORS - OUTPUTS
The device is used to control electrical loads of three different building systems that are typically
used in a residential, office or hotel room:
The first output (O1) allows the control of electrically-operated Venetian blinds, roller shutters,
awnings, venting louvers or similar blinds for 230 V AC mains voltage. The relay contacts for the
movement directions (up, down) are bistable, meaning that the last switching status set also
remains intact, should the mains voltage fail.
Furthermore, the device has one additional electronic switching output (O2), which allows silent
control of electrothermal valve drives for heating or cooling systems. Up to 2 electrothermal
valve drives can be connected to these electronic output, which is protected against overload
and short-circuit.
The functionalities that can be preset with the ETS for the Venetian blind output include, for
instance, separately configurable travelling times, enlarged feedback functions, assignment to
up to 5 different safety functions, an extensive sun protection function, and incorporation into
scenes or forced-position applications.
The electronic switching output has the following scope of functions: conversion of constant
command value telegrams into a pulse-width modulated output signal (PWM). This provides
quasi-constant activation of the connected valve drives. Alternatively, conversion of switching
command values. Status messaging for valve position and cyclical monitoring of the command
value telegrams. Emergency operation in the event of bus voltage return and forced position via
bus telegram in summer and winter mode. Alarm message in case of short-circuit or overload of
the switching output and anti-sticking protection for the valves. Valve drives that are closed or
open when deenergised can be connected. The status message "valve closed" can be
transmitted to the bus for further processing or displaying the information on other bus devices.
Besides the two outputs, the device possesses three additional inputs, which can have an
internal effect on the Venetian blind output or, alternatively, affect the KNX/EIB separately,
depending on the ETS configuration. The connected potential-free switch or button contacts are
downloaded to the device via a shared reference potential. With the internal effect, inputs 1 and
2 directly operate the Venetian blind output. With the effect on the bus, the inputs can,
independently of one another, transmit telegrams for switching or dimming for Venetian blind
control or value encoder use (dimming value encoder, light scene extension).
The connection of 230 V signals or other external voltages to the extension inputs is not
permitted!
16201
MEG6003-0006 KNX ACTUATOR, BLIND- A.HEATINGT.FM W.3 INPUTS ACTUATORS - OUTPUTS
16451 MEG6212-0344 Push-Button 2-gang plus with room temperature controller, System M CLIMATE CONTROL
Im Design System M.
Komfortable Steuerungseinheit mit 4 Bedientasten,
Betriebs-, Statusanzeige und Schriftfeld.
Die Betriebsanzeige kann auch als Orientierungslicht
verwendet werden.
Mit Raumtemperaturregler und Display.
Mit 5 roten LEDs.
Der Raumtemperaturregler ist für Heizung und
Kühlung mit stufenlos verstellbaren KNX-Stellantrieben
oder zur Ansteuerung von Schaltaktoren
und Heizungsaktoren verwendbar. Mit weiß
hinterleuchtetem Display zur Darstellung von z.
B. Uhrzeit, Datum, Temperatur und Betriebsmodus.
For System M. Convenient control unit with 4 operating buttons, operating and status display and labeling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With 5 red LEDs. The room thermostat is suitable for heating and cooling with infinitely adjustable KNX valve drives or to trigger switch actuators and heating actuators. With white backlit display for showing eg the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working / non-working day (external control), display mode, time, switching times and brightness of the display. The buttons are as a pair (dual-surface) or as single buttons freely programmable .. With integrated bus coupler. The bus is connected using a bus connecting terminal. KNX software functions: Functions button: Switching, toggling, dimming, blind control (relative or absolute), pulse edges Dissolve 1, - 2 -, 4 - or 8-bit telegrams (distinction between short / long operation), pulse edges with 2-byte read telegrams (distinction between short / long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronization, alarm function, external temperature value cyclically, fan control, operating modes, setpoint shift. Functions of the room temperature controller: Controller Type: 2-step control, continuous PI control, switching PI control (PWM). Output: Continuous in the range 0 .. 100 % or switching ON / OFF. Controller mode:
Heating with one controller output.
Cooling with one controller output.
Heating and cooling with separate controller outputs.
Heating and cooling with one controller output.
2-step heating with 2 control outputs.
2-step cooling with 2 control outputs.
2-stage heating and cooling with 4 control outputs. Operating modes: Comfort, comfort extension, standby, night setback, Frost-/Hitzeschutz. Move all setpoints. Save all setpoint temperatures and operating modes when reset. Monitor external temperature. Additional Output of control value as 1 byte value on the PWM. Monitoring function for the actual temperature, valve protection function .. function scene. Operation: Menu. Contents: With bus connecting terminal and supporting plate. With Screw for protection against dismantling. With protective hood for plaster. Material: Thermoplastic brilliant. Color: polar white glossy.
16451
MEG6212-0344 PUSH-BUTTON 2-GANG PLUS WITH ROOM TEMPERATURE CONTROLLER, SYSTEM M CLIMATE CONTROL
18216 MEG6700-0002 Switching Actuator 2 channels Capacitive Outputs ACTUATORS - OUTPUTS
For the independent switching of 2 loads through making contacts. All 230 V switching outputs can be manually activated with manual switches. With an integrated bus coupler.
A green LED indicates that the application is ready for use.
KNX Software Functions:
Function of ladder lighting time with or without manual function off WARNING for ladder lighting time function, link, active regeneration per channel, central function, parameterization of bus voltage and grog.

Voltage (rated voltage): AC 100-240 V, 50-60 Hz
Tolerance range: minimum AC 90 V - Max AC 265 V per contact switch:
Rated current: 16 A, inductive load cosf = 0.6
power
Incandescent lamps: AC 100, up to 1600 W, AC MAX 3600 W, 230 V, 240 V AC, up to 3840 W
Halogen lamps: AC MAX 1080 W, 100 V, AC up to 2500 W, 230 V, 240 V AC, Max 2500 W
Fluorescent lamps: AC 100, maximum 900 VA, Max 2000 VA AC 240 V, 230 V AC, max. 2000 VA parallel offset
Capacitive load: AC 230 V, 16 A, maximum 105 ?f
Device width: 2.5 = approx. 45 mm
18216
MEG6700-0002 SWITCHING ACTUATOR 2 CHANNELS CAPACITIVE OUTPUTS ACTUATORS - OUTPUTS
18217 MEG6700-0004 4-Channel Actuator 16A Capacitive Loads ACTUATORS - OUTPUTS
For independent switching of 2 loads via NO contacts. All 230 V switch outputs can be manually operated by hand switches. With integrated bus coupler.
A green LED indicates that the application is ready for operation.
Software functions KNX:
Staircase lighting function with / without manual OFF function, switch-off warning for staircase lighting time function, link, active feedback signal per channel, central function, parameterization for bus voltage failure and recovery.

Rated voltage (nominal voltage): AC 100-240 V, 50-60 Hz


Tolerance range: min. AC 90 V - max. AC 265V
For each switching contact:
Rated current: 16 A, inductive load cosf = 0.6
rated capacity

Incandescent lamps: AC 100, max. 1600 W
AC 230 V, max. 3600 W
AC 240 V, max. 3840 W

Halogen lamps: AC 100 V, max. 1080 W
AC 230 V, max. 2500 W
AC 240 V, max. 2500 W

Fluorescent lamps: AC 100, max. 900 VA
AC 230 V, max. 2000 VA
AC 240 V, max. 2000 VA

Parallel compensated
Capacitive load: AC 230 V, 16 A, max. 105 µF
Width of the device: 2.5 TE = approx. 45 mm
18217
MEG6700-0004 4-CHANNEL ACTUATOR 16A CAPACITIVE LOADS ACTUATORS - OUTPUTS
18218 MEG6700-0008 8-channel actuator. Capacitive loads. ACTUATORS - OUTPUTS
For independent switching of 2 loads via NO contacts. All 230 V switch outputs can be manually operated by hand switches. With integrated bus coupler.
A green LED indicates that the application is ready for operation.
Software functions KNX:
Staircase lighting function with / without manual OFF function, switch-off warning for staircase lighting time function, link, active feedback signal per channel, central function, parameterization for bus voltage failure and recovery.

Rated voltage (nominal voltage): AC 100-240 V, 50-60 Hz


Tolerance range: min. AC 90 V - max. AC 265V
For each switching contact:
Rated current: 16 A, inductive load cosf = 0.6

rated capacity
Incandescent lamps: AC 100, max. 1600 W
AC 230 V, max. 3600 W
AC 240 V, max. 3840 W

Halogen lamps: AC 100 V, max. 1080 W
AC 230 V, max. 2500 W
AC 240 V, max. 2500 W

Fluorescent lamps: AC 100, max. 900 VA
AC 230 V, max. 2000 VA
AC 240 V, max. 2000 VA

Parallel compensated

Capacitive load: AC 230 V, 16 A, max. 105 µF

Width of the device: 2.5 TE = approx. 45 mm
18218
MEG6700-0008 8-CHANNEL ACTUATOR. CAPACITIVE LOADS. ACTUATORS - OUTPUTS
1452 550619 Surface-mounted housing for ARGUS Presence DETECTORS
The surface-mounted housing for ARGUS Presence devices also allows them to be surface mounted. To be completed with: ARGUS Presence, art. no. 550590/91. INSTABUS ARGUS Presence, art. no. 6307.., 6308.., 6309
1452
550619 SURFACE-MOUNTED HOUSING FOR ARGUS PRESENCE DETECTORS
1480 618319 Labelling sheets for push-buttons SIN FAMILIA
Labelling sheets for push-buttons For individual labelling of the System M push-buttons with text or symbols. ˜ To be completed with:System M push-button, 1-gang, 2-gang or 4- gang, art. no. 6171.., 6275.., 6208.., 6233.., 6172.., 6276.., 6209.., 6234.., 6174.., 6278.., 6210.., 6238.., 6291.., 6241... Accessories: Labelling software, art. no. 615022. — Contents: 1 sheet for every 28 products.
1480
618319 LABELLING SHEETS FOR PUSH-BUTTONS SIN FAMILIA
1482 618419 Labelling sheets for multi-function push-button with IR receiver PUSH BUTTONS
Labelling sheets for multi-function push-button with IR receiver For individual labelling of the System M multi-function push-button with IR receiver. ˜ To be completed with:System M multi-function push-button with IR receiver, art. no. 6175.., 6279.., 6292.., 6242... Accessories: Labelling software, art. no. 615022. — Contents: 1 sheet for every 28 products.
1482
618419 LABELLING SHEETS FOR MULTI-FUNCTION PUSH-BUTTON WITH IR RECEIVER PUSH BUTTONS
1698 625144 Rocker for 1-gang push-button module white, system m PUSH BUTTONS
Rocker for 1-gang push-button module For System M. The rocker is attached to the 1-gang push-button module. ~ In KNX, to be completed with: EIB push-button module, 1-gang, art. no. System M 625199. Accessories: Protective hood for plaster, System M, art. no. 627591...
1698
625144 ROCKER FOR 1-GANG PUSH-BUTTON MODULE WHITE, SYSTEM M PUSH BUTTONS
1703 625244 Rockers for 2-gang push-button module white ,system PUSH BUTTONS
Rockers for 2-gang push-button module For System M. The rockers are attached to the 2-gang push-button module. ˜ In INSTABUS EIB EASY, to be completed with: Easy push-button module, 2-gang, art. no. 762192
1703
625244 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WHITE ,SYSTEM PUSH BUTTONS
1713 626144 Rocker for 1-gang push-button module white PUSH BUTTONS
Rocker for 1-gang push-button module For System Design. The rocker is attached to the 1-gang push-button module. ~ In INSTABUS EIB EASY, to be completed with: Easy push-button module, 1-gang, art. no. 761191
1713
626144 ROCKER FOR 1-GANG PUSH-BUTTON MODULE WHITE PUSH BUTTONS
1719 626244 Rockers for 2-gang push-button module, white PUSH BUTTONS
Rockers for 2-gang push-button module For System Design. The rockers are attached to the 2-gang push-button module. ˜ In INSTABUS EIB, to be completed with: Push-button module, 2- gang, art. no. 626299. In INSTABUS EIB EASY, to be completed with: Easy push-button module, 2-gang, art. no. 761192
1719
626244 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE, WHITE PUSH BUTTONS
1723 626419 Rocker for 1-gang push-button module with 1/0 imprint polar white PUSH BUTTONS
Rocker for 1-gang push-button module with 1/0 imprint For System Design. The rocker is attached to the 1-gang push-button module. ~ In KNX, to be completed with: EIB push-button module, 1-gang, art. no. System Design 626199. Accessories: Protective hood for plaster, System Design, art. no. 628091... - Availability: New articles available June 2007.
1723
626419 ROCKER FOR 1-GANG PUSH-BUTTON MODULE WITH 1/0 IMPRINT POLAR WHITE PUSH BUTTONS
1724 626519 Rocker for 1-gang push-button module with up/down arrow imprint polar white PUSH BUTTONS
Rocker for 1-gang push-button module with up/down arrow imprint For System Design. The rocker is attached to the 1-gang push-button module. ~ In KNX, to be completed with: EIB push-button module, 1-gang, art. no. System Design 626199. Accessories: Protective hood for plaster, System Design, art. no. 628091... - Availability: New articles available June 2007. Thermoplastic brilliant polar white
1724
626519 ROCKER FOR 1-GANG PUSH-BUTTON MODULE WITH UP/DOWN ARROW IMPRINT POLAR WHITE PUSH BUTTONS
1725 626619 Rockers for 2-gang push-button module with 1/0 and up/down arrow imprint polar white PUSH BUTTONS
Rockers for 2-gang push-button module with 1/0 and up/down arrow imprint For System Design. The rockers are attached to the 2-gang push-button module. ~ To be completed with: Push-button module, 2-gang, art. no. System Design 568199. In KNX, to be completed with: EIB push-button module, 2-gang, art. no. System Design 626299. Accessories: Protective hood for plaster, System Design, art. no. Thermoplastic brilliant polar white 628091... - Availability: New articles available June 2007
1725
626619 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WITH 1/0 AND UP/DOWN ARROW IMPRINT POLAR WHITE PUSH BUTTONS
1726 626719 Rockers for 2-gang push-button module with up/down arrow and 1/0 imprint PUSH BUTTONS
Rockers for 2-gang push-button module with up/down arrow and 1/0 imprint For System Design. The rockers are attached to the 2-gang push-button module. ~ To be completed with: Push-button module, 2-gang, art. no. System Design 568199. In KNX, to be completed with: EIB push-button module, 2-gang, art. no. System Design 626299. Accessories: Protective hood for plaster, System Design, art. no. 628091... - Availability: New articles available June 200 ~ Thermoplastic brilliant polae white
1726
626719 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WITH UP/DOWN ARROW AND 1/0 IMPRINT PUSH BUTTONS
1754 639110 Valve adapter VA10 for thermoelectric valve drive CLIMATE CONTROL
Valve adapter VA10 for thermoelectric valve drive For Dumser, Vescal, Simplex. Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors To be completed with: Thermoelectric valve drive 230 V, art. no. 639125. Thermoelectric valve drive 24 V, art. no. 639124
1754
639110 VALVE ADAPTER VA10 FOR THERMOELECTRIC VALVE DRIVE CLIMATE CONTROL
1759 639150 Ventiladapter VA50 CLIMATE CONTROL
Für Honeywell+Braukmann, Reich, Landis+ Gyr, MNG, Cazzagniga. Ventiladapter zur Anpassung an verschiedene Ventilunterteile und Heizkreisverteiler. Zu komplettieren mit: Thermoelektrischer Stellantrieb 230 V Art.-Nr. 639123, 639125. Thermoelektrischer Stellantrieb 24 V Art.-Nr. 639124. Fabrikat: Merten Art.-Nr.: 639150 oder gleichwertig
1759
639150 VENTILADAPTER VA50 CLIMATE CONTROL
1760 639178 Valve adapter VA78 for thermoelectric valve drive CLIMATE CONTROL
Valve adapter VA78 for thermoelectric valve drive For Danfoss RA. Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors ˜ To be completed with: Thermoelectric valve drive 230 V, art. no. 639125. Thermoelectric valve drive 24 V, art. no. 639124
1760
639178 VALVE ADAPTER VA78 FOR THERMOELECTRIC VALVE DRIVE CLIMATE CONTROL
1761 639180 Valve adapter VA80 for thermoelectric valve drive SIN FAMILIA
Valve adapter VA80 for thermoelectric valve drive For Heimeier, Herb, Onda, Schlösser (from 1993), Oventrop M30x1.5, TeSa. Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors ˜ To be completed with: Thermoelectric valve drive 230 V, art. no. 639125. Thermoelectric valve drive 24 V, art. no. 639124.
1761
639180 VALVE ADAPTER VA80 FOR THERMOELECTRIC VALVE DRIVE SIN FAMILIA
1831 662929 Cable cover for REG-K, light grey OTHER ACCESSORIES
Cable cover for REG-K For covering the stripped bus cable in all REG-K devices. The cable cover guarantees a safe distance between the SELV bus voltage and the mains voltage. light grey
1831
662929 CABLE COVER FOR REG-K, LIGHT GREY OTHER ACCESSORIES
1834 663593 Brightness sensor SENSORS
Brightness sensor The brightness sensor is required for recording and evaluating brightness. Brightness is recorded via a photoelectric diode and electronically converted into an analogue output signal of 0 V - 10 V. For external installation and connection to the weather station REG-K/4-gang or the analogue input REG-K/4-gang. These two devices provide the supply voltage necessary to operate the sensor. Measuring range: 0 to 60,000 lux, linear Output: 0 ... 10 V short-circuit-proof External power supply: Voltage: 24 V DC (15-30 V DC) Power consumption: approx. 5 mA General specifications: Incoming cable: using PG7 screw fitting Recommended cable: 3 x 0.25 mm2 Type of protection: IP 65 Dimensions: 58 x 35 x 64 (W x H x D) ˜ In KNX, to be completed with: Weather station REG-K/4-gang, art. no. 682991. Analogue input REG-K/4-gang, art. no. 682191. Analogue input module REG/4-gang, art. no. 682192
1834
663593 BRIGHTNESS SENSOR SENSORS
1948 689702 Branch terminal, yellow/white SYSTEM DEVICES
Branch terminal, yellow/white Branch terminal comprising two interlocking terminal parts in yellow and white, each with 4 plug-in terminals. For solid conductors with a diameter of 0.6 to 0.8 mm. For wiring the yellow/white cores of the bus cable.
1948
689702 BRANCH TERMINAL, YELLOW/WHITE SYSTEM DEVICES
1953 690098 Protective cover for plaster, black OTHER ACCESSORIES
Protective cover for plaster For protecting the bus coupler, flush-mounted actuators, Easy flush-mounted modules or actuators from damage during painting and decorating work. ˜ In KNX, to be completed with: Bus coupler, flush-mounted, art. no. 690099. Bus coupler, flush-mounted 2, art. no. 690299. Switch actuator, flush-mounted, art. no. 627099. Series actuator, flush-mounted, art. no. 627199. Blind actuator, flush-mounted, art. no. 627299.
1953
690098 PROTECTIVE COVER FOR PLASTER, BLACK OTHER ACCESSORIES
4435 639190 PROGRAMMING MAGNET SYSTEM DEVICES
Programming magnet for: EMO valve drive Art.-Nr. 639119. EMO valve drive with 2 binary inputs Art.-Nr. 639118. KND ARGUS 220 Connect Art.-Nr. 6325...
4435
639190 PROGRAMMING MAGNET SYSTEM DEVICES
4457 663529 Power supply REG, AC 24 V/1 A SYSTEM DEVICES
Power supply REG, AC 24 V/1 A Power supply for 24 V binary inputs, weather station REG-K/4-gang, analogue input module REGK/ 4-gang, rain sensor, wind sensor with 0-10 V interface and heating. For installation onto DIN rails EN 50022. With fuse. Primary supply: AC 230 V, +/- 10 %, 50-60 Hz Output voltage: AC 24 V Output current: max. 1 A Fuse: 5x20 mm, 250 V, T 160 mA Device width: 5 modules = approx. 90 mm ˜ For supplying power to: Binary input REG-K/4x24 art. no. 644890. Binary input REG-K/8x24 art. no. 644790. Binary input REG-K/8x24 art. no. 644792. Weather station REG-K/4-gang, art. no. 682991. Analogue input module REG/4-gang Art. No. 682192. Rain sensor for art. no. 663595. Wind sensor with 0-10V interface and heating, art. no. 663592.
4457
663529 POWER SUPPLY REG, AC 24 V/1 A SYSTEM DEVICES
4725 296019 Central plate for telephone socketoutlet TAE. polar white, glossy SIN FAMILIA
Central plate for telephone socketoutlet TAE For System M. For telephone socket-outlets TAE or TDO, combination socket-outlets RJ45/TAE or flush-mounted USB interface. ˜ To be completed with:Telephone socket-outlet TAE, art. no. 4652...Loudspeaker connection insert art. no. 4670...USB interface, flush-mounted, art. no. 681799.Telephone socket-outlet TDO, art. no. 465930. polar white, glossy
4725
296019 CENTRAL PLATE FOR TELEPHONE SOCKETOUTLET TAE. POLAR WHITE, GLOSSY SIN FAMILIA
4726 296025 Central plate for telephone socketoutlet TAE. active white, glossy SIN FAMILIA
Central plate for telephone socketoutlet TAE For System M. For telephone socket-outlets TAE or TDO, combination socket-outlets RJ45/TAE or flush-mounted USB interface. ˜ To be completed with:Telephone socket-outlet TAE, art. no. 4652...Loudspeaker connection insert art. no. 4670...USB interface, flush-mounted, art. no. 681799.Telephone socket-outlet TDO, art. no. 465930.
4726
296025 CENTRAL PLATE FOR TELEPHONE SOCKETOUTLET TAE. ACTIVE WHITE, GLOSSY SIN FAMILIA
4727 296044 Central plate for telephone socketoutlet TAE, white, glossy SIN FAMILIA
Central plate for telephone socketoutlet TAE For System M. For telephone socket-outlets TAE or TDO, combination socket-outlets RJ45/TAE or flush-mounted USB interface. ˜ To be completed with:Telephone socket-outlet TAE, art. no. 4652...Loudspeaker connection insert art. no. 4670...USB interface, flush-mounted, art. no. 681799.Telephone socket-outlet TDO, art. no. 465930 white, glossy
4727
296044 CENTRAL PLATE FOR TELEPHONE SOCKETOUTLET TAE, WHITE, GLOSSY SIN FAMILIA
4799 626819 Rockers for 2-gang push-button module with up/down arrow imprint, polar white PUSH BUTTONS
Rockers for 2-gang push-button module with up/down arrow imprint For System Design. The rockers are attached to the 2-gang push-button module. ~ To be completed with: Push-button module, 2-gang, art. no. System Design 568199. In INSTABUS EIB EASY, to be completed with: Easy push-button module, 2-gang, art. no. System Design 761192. Accessories: Protective hood for plaster, System Design, art. no. 628091...
4799
626819 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WITH UP/DOWN ARROW IMPRINT, POLAR WHITE PUSH BUTTONS
4853 693003 Power supply REG, 24 V DC / 0.4 A SYSTEM DEVICES
Power supply REG, 24 V DC / 0.4 A Power supply for 24 V binary inputs, IC 1 EIB Internet controller REG-K, panel control REG-K. For installation onto DIN rails EN 50022. With integrated overload and short-circuit protection. Primary supply: AC 230 V, 48-63 Hz Output voltage: DC 24 V +/- 3 % Output current: max. 0.4 A Output power: max. 10 W Device width: 1 module = approx. 18 mm ˜ For supplying power to: Binary input REG-K/4x24 art. no. 644890. Binary input REG-K/8x24 art. no. 644790. Binary input REG-K/8x24 art. no. 644792. IC 1 EIB Internet controller merten@home REG-K, art. no. 6951... Panel control REG-K/12x24 art. no. 675001. Panel control REG-K/8-4x24 art. no. 675101. Universal I/O panel control REG-K/32x24 art. no. 675201.
4853
693003 POWER SUPPLY REG, 24 V DC / 0.4 A SYSTEM DEVICES
4854 693004 Power supply REG, 24 V DC / 1 A SYSTEM DEVICES
Power supply REG, 24 V DC / 1 A Power supply for 24 V binary inputs, IC 1 EIB Internet controller REG-K, panel control REG-K. For installation onto DIN rails EN 50022. With integrated overload and short-circuit protection. Primary supply: AC 90-260 V, 48-63 Hz Output voltage: DC 24 V +/- 3 % Output current: max. 1 A Output power: max. 24 W Device width: 5 modules = approx. 90 mm ˜ For supplying power to: Binary input REG-K/4x24 art. no. 644890. Binary input REG-K/8x24 art. no. 644790. Binary input REG-K/8x24 art. no. 644792. IC 1 EIB Internet controller merten@home REG-K, art. no. 6951... Panel control REG-K/12x24 art. no. 675001. Panel control REG-K/8-4x24 art. no. 675101. Universal I/O panel control REG-K/32x24 art. no. 675201.
4854
693004 POWER SUPPLY REG, 24 V DC / 1 A SYSTEM DEVICES
5542 486119 FRAME POLAR WHITE , SERIE M-PLAN SIN FAMILIA
M-PLAN frame, 1-gang Polar white
5542
486119 FRAME POLAR WHITE , SERIE M-PLAN SIN FAMILIA
5578 488119 FRAME POLAR WHITE , SERIE M-PLAN II SIN FAMILIA
M-PLAN II frame, 1-gang, flushmounted For flush-mounting in walls. To be completed with: Flush-mounting adapter for M-PLAN II frame, art. no. 512403. Accessories: Concrete wall adapter, art. no. 512499
5578
488119 FRAME POLAR WHITE , SERIE M-PLAN II SIN FAMILIA
5579 489178 FRAME SAPPHIRE, SERIE M-PLAN SIN FAMILIA
M-PLAN real glass frame, 1-gang
5579
489178 FRAME SAPPHIRE, SERIE M-PLAN SIN FAMILIA
5596 433119 Rocker polar white SIN FAMILIA
Thermoplastic classy matt Rocker For two-way switch, intermediate switch and pushbutton insert.
5596
433119 ROCKER POLAR WHITE SIN FAMILIA
5637 476119 FRAME POLAR WHITE , SERIE M-PLAN SIN FAMILIA
M-PLAN frame, 1-gang, with labelling option M-PLAN frame, 1-gang, with labelling option ~ Accessories: Labelling strips for M-PLAN frames with labelling option, art. no. 486100. - Contents: 1 labelling strip and 1 window per frame.
5637
476119 FRAME POLAR WHITE , SERIE M-PLAN SIN FAMILIA
5638 466099 Broadband cable/satellite antenna branch-circuit box, 2-gang SIN FAMILIA
Broadband cable/satellite antenna branch-circuit box, 2-gang DIN EN 50083-1/A1, DIN EN 80083-2/A1 Broadband directional coupler box for branch-circuit and star-type distribution systems in broadband cable, communal aerial and satellite distribution systems. With DC transmission via the TV connection. Suitable for flush-mounted boxes of Ø 55-65 mm. With claw and screw fixing. DC transmission: max. 24 V/400 mA Signal: 22 kHz and DiSEqC To be completed with:Central plate for antenna socket-outlet, art. no. System M 2967.., 2975.., System Basis 2948.., System Design 2941.., OCTOCOLOR 2943...
5638
466099 BROADBAND CABLE/SATELLITE ANTENNA BRANCH-CIRCUIT BOX, 2-GANG SIN FAMILIA
5639 297519 Central plate for antenna socketoutlets polar white SIN FAMILIA
For AEG, Astro Bosch, Fuba, Hirschmann, Kathrein, Philips, Polytron, Siemens, Wisi, Zehnder etc. Third opening can be broken open for satellite socket. To be completed with:Broadband cable/satellite through-way box, 2-gang, art. no. 466098.Broadband cable/satellite branch-circuit box, 2-gang, art. no. 466099.Satellite antenna socket-outlet, 3- gang, art. no. 466097
5639
297519 CENTRAL PLATE FOR ANTENNA SOCKETOUTLETS POLAR WHITE SIN FAMILIA
5640 465701 RJ45 insert 8/8 SIN FAMILIA
For connecting analogue or digital terminal units via two 8-pole RJ45 connectors. With screw terminals. ~ To be completed with:Central plate for RJ45 insert, 2-gang, art. no. System M 2961.., 2980.., System Basis 2927.., System Design 2926.., or OCTOCOLOR 2920... - Technical Information: RJ45
5640
465701 RJ45 INSERT 8/8 SIN FAMILIA
5641 298019 Central plate for RJ45 insert, 2-gang polar whait SIN FAMILIA
For System M. For RJ45 inserts 8/8, 2x8, Line 21 RJ45 insert 8/ 8, RJ45 inserts by Rutenbeck or E-DAT designs by BTR. To be completed with:RJ45 insert 8/8, art. no. 465701.RJ45 insert 2x8, art. no. 465702.RJ45 insert 8/8 Cat 5e, art. no. 465703.RJ45 insert 8/8 Cat 6, art. no. 465706.
5641
298019 CENTRAL PLATE FOR RJ45 INSERT, 2-GANG POLAR WHAIT SIN FAMILIA
5664 484219 FRAME POLAR WHITE , SERIE M-SMART SIN FAMILIA
M-SMART frame, 2-gang polar whait For vertical and horizontal installation. Thermoplastic classy matt
5664
484219 FRAME POLAR WHITE , SERIE M-SMART SIN FAMILIA
5665 484319 M-SMART frame, 3-gang polar white SIN FAMILIA
M-SMART frame, 3-gang For vertical and horizontal installation. Thermoplastic classy matt polar white
5665
484319 M-SMART FRAME, 3-GANG POLAR WHITE SIN FAMILIA
5704 565291 MOUNTING BRACKET, POLAR WHITE SIN FAMILIA
Installation bracket for attaching the ARGUS 110/ 220 Basic, Timer or Connect to outer or inner corners. Can also be secured to fixed pipes (VDE 0100) with conventional conduit clips. ~ To be completed with: ARGUS 110/220 Basic, art. no. 565119, 565219. ARGUS 220 Connect art. no. 5654... ARGUS 220 Timer, art. no. 5656... INSTABUS ARGUS 220 Connect art. no. 5315... - Technical Information: ARGUS movement detector (?? p. 492) - Contents: With screws and plugs. Without conduit clip.
5704
565291 MOUNTING BRACKET, POLAR WHITE SIN FAMILIA
5738 481119 FRAME POLAR WHITE , SERIE ARTEC SIN FAMILIA
ARTEC frame, 1-gang Thermoplastic brilliant white
5738
481119 FRAME POLAR WHITE , SERIE ARTEC SIN FAMILIA
6005 435519 Rocker for roller shutter switch and push-button SIN FAMILIA
For roller shutter rocker switch and rocker button insert.
6005
435519 ROCKER FOR ROLLER SHUTTER SWITCH AND PUSH-BUTTON SIN FAMILIA
6015 486219 FRAME POLAR WHITE , SERIE M-PLAN SIN FAMILIA
M-PLAN frame, 2-gang For vertical and horizontal installation. Thermoplastic classy matt polar white
6015
486219 FRAME POLAR WHITE , SERIE M-PLAN SIN FAMILIA
6167 412146 pushbutton 1 gang stainless steel SIN FAMILIA
Rocker For two-way switch, intermediate switch and pushbutton insert.
6167
412146 PUSHBUTTON 1 GANG STAINLESS STEEL SIN FAMILIA
6168 412546 Rocker for two-circuit switch stainless steel SIN FAMILIA
Rocker for two-circuit switch For two-way, double two-way switch and double push-button insert.
6168
412546 ROCKER FOR TWO-CIRCUIT SWITCH STAINLESS STEEL SIN FAMILIA
7697 481246 FRAME STAINLESS STEEL, SERIE ARTEC SIN FAMILIA
ARTEC frame, 2-gang For vertical and horizontal installation. Metallic stainless steel
7697
481246 FRAME STAINLESS STEEL, SERIE ARTEC SIN FAMILIA
7725 435560 Rocker for roller shutter switch and push-button SIN FAMILIA
Rocker for roller shutter switch and push-button For roller shutter rocker switch and rocker button insert.
7725
435560 ROCKER FOR ROLLER SHUTTER SWITCH AND PUSH-BUTTON SIN FAMILIA
7727 617819 Labelling sheets for push-button plus SIN FAMILIA
For individual labelling of the System Design pushbutton plus with text or symbols. ~ To be completed with:System Design push-button plus, art. no. 6280.., 6281.., 6282.., 6283.., 6284... Accessories: Labelling software, art. no. 615022. - Contents: 1 sheet for 20 products
7727
617819 LABELLING SHEETS FOR PUSH-BUTTON PLUS SIN FAMILIA
7728 481944 FRAME WHITE, SERIE ARTEC SIN FAMILIA
~ In KNX, to be completed with: Multi-function push-button, 4-gang, with room temperature control unit, art. no. System Design 6288 ........
7728
481944 FRAME WHITE, SERIE ARTEC SIN FAMILIA
7730 481960 FRAME ALUMINIUM, SERIE ARTEC SIN FAMILIA
Abmessungen: 80,5 x 111,7 mm (BxH) Im KNX zu komplettieren mit: Multifunktions-Taster 4fach mit Raumtemperaturregler System Fläche Art.- Nr. 6288... Material: Thermoplast brillant Ausführung: aluminium Fabrikat: Merten Art.-Nr.: 481960 oder gleichwertig
7730
481960 FRAME ALUMINIUM, SERIE ARTEC SIN FAMILIA
7944 297960 Central plate for telephone socket outlet SIN FAMILIA
For telephone socket-outletsTAE or TDO, combination socket-outlets RJ45/TAE or flush-mounted USB interface. ~ To be completed with: Telephone socket-outlet TAE, art. no. 4652... Telephone socket-outlet TDO, art. no. 465930. Combination socket-outlet RJ45/TAE (Cat 3), art. no. 465707. Line 21 combination socket-outlet RJ45/TAE, art. no. 465709. USB interface, flush-mounted, art. no. 681799.
7944
297960 CENTRAL PLATE FOR TELEPHONE SOCKET OUTLET SIN FAMILIA
7945 433160 Rocker For two-way switch, intermediate switch and pushbutton insert, aluminium SIN FAMILIA
For two-way switch, intermediate switch and pushbutton insert
7945
433160 ROCKER FOR TWO-WAY SWITCH, INTERMEDIATE SWITCH AND PUSHBUTTON INSERT, ALUMINIUM SIN FAMILIA
7946 433560 Rocker for two-circuit switch aluminium SIN FAMILIA
Rocker for two-circuit switch Rocker for two-circuit switch For two-way, double two-way switch and double push-button insert.
7946
433560 ROCKER FOR TWO-CIRCUIT SWITCH ALUMINIUM SIN FAMILIA
8499 478125 FRAME ARTIC WHITE BRIGHT, SERIE M-SMART SIN FAMILIA
Thermoplastic brilliant active white, glossy
8499
478125 FRAME ARTIC WHITE BRIGHT, SERIE M-SMART SIN FAMILIA
9009 625444 Rocker for 1-gang push-button module with 1/0 imprint PUSH BUTTONS
Rocker for 1-gang push-button module with 1/0 imprint For System M. The rocker is attached to the 1-gang push-button module. ~ In KNX, to be completed with: EIB push-button module, 1-gang, art. no. System M 625199. Accessories: Protective hood for plaster, System M, art. no. 627591...
9009
625444 ROCKER FOR 1-GANG PUSH-BUTTON MODULE WITH 1/0 IMPRINT PUSH BUTTONS
9010 625544 Rocker for 1-gang push-button module with up/down arrow imprint PUSH BUTTONS
For System M. The rocker is attached to the 1-gang push-button module. ~ In KNX, to be completed with: EIB push-button module, 1-gang, art. no. System M 625199. Accessories: Protective hood for plaster, System M, art. no. 627591...
9010
625544 ROCKER FOR 1-GANG PUSH-BUTTON MODULE WITH UP/DOWN ARROW IMPRINT PUSH BUTTONS
9011 625644 Rockers for 2-gang push-button module with 1/0 and up/down arrow imprint PUSH BUTTONS
For System M. The rockers are attached to the 2-gang push-button module. ~ To be completed with: Push-button module, 2-gang, art. no. System M 568499. In KNX, to be completed with: EIB push-button module, 2-gang, art. no. System M 625299. Accessories: Protective hood for plaster, System M, art. no. 627591
9011
625644 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WITH 1/0 AND UP/DOWN ARROW IMPRINT PUSH BUTTONS
9012 625744 Rockers for 2-gang push-button module with up/down arrow and 1/0 imprint polar white PUSH BUTTONS
Rockers for 2-gang push-button module with up/down arrow and 1/0 imprint For System M. The rockers are attached to the 2-gang push-button module. ~ To be completed with: Push-button module, 2-gang, art. no. System M 568499. In KNX, to be completed with: EIB push-button module, 2-gang, art. no. System M 625299. Accessories: Protective hood for plaster, System M, art. no. 627591...
9012
625744 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WITH UP/DOWN ARROW AND 1/0 IMPRINT POLAR WHITE PUSH BUTTONS
9013 625844 Rockers for 2-gang push-button module with up/down arrow imprint PUSH BUTTONS
For System M. The rockers are attached to the 2-gang push-button module. ~ To be completed with: Push-button module, 2-gang, art. no. System M 568499. In KNX, to be completed with: EIB push-button module, 2-gang, art. no. System M 625299. Accessories: Protective hood for plaster, System M, art. no. 627591..
9013
625844 ROCKERS FOR 2-GANG PUSH-BUTTON MODULE WITH UP/DOWN ARROW IMPRINT PUSH BUTTONS
9027 616790 SENSOR FOR Room temperature control unit CLIMATE CONTROL
SENSOR FOR Room temperature control unit
9027
616790 SENSOR FOR ROOM TEMPERATURE CONTROL UNIT CLIMATE CONTROL
9066 412560 Rocker for two-circuit switch system flache, aluminium SIN FAMILIA
Rocker for two-circuit switch For two-way, double two-way switch and double push-button insert
9066
412560 ROCKER FOR TWO-CIRCUIT SWITCH SYSTEM FLACHE, ALUMINIUM SIN FAMILIA
9135 663992 mast and corner fastening SENSORS
For mast and corner installation, the wall bracket is installed using a mast and corner fastening
9135
663992 MAST AND CORNER FASTENING SENSORS
9218 488844 MERT Rahmen 2fach ohne Mittelsteg 488844 M-PLAN weiss SIN FAMILIA
Rahmen
9218
488844 MERT RAHMEN 2FACH OHNE MITTELSTEG 488844 M-PLAN WEISS SIN FAMILIA
9232 668991 LEAD GEL BATTERY DC 12 V, 18 AH SYSTEM DEVICES
Lead gel battery for connecting to the emergency power supply REG. Nominal voltage: DC 12 V Capacity: 18 Ah In KNX, to be completed with: REG emergency power supply, art. no. 683901.
9232
668991 LEAD GEL BATTERY DC 12 V, 18 AH SYSTEM DEVICES
9272 639125 Thermoelectric valve drive 230 V CLIMATE CONTROL
Thermoelectric valve drive for opening and closing valves. For 2-step or PWM control of heating, air conditioning and ventilation systems, individual room control of surface heaters, control of heating circuit distributors, radiators, convector heaters, cooling ceilings. Operation is carried out by the heating actuator REG-K/ 6x230/0.05 A or a room temperature control unit (230 V) with 2-step or PWM output. Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors. Functions: • First-open function: The drive is factory-set to de-energised open. This allows the heating to be operated during the building shell phase. • De-energised closed • Functional display (open, closed, intermediate settings) • Adjustment control • Protection against dismantling • Plug-in connecting cable • Plug-in assembly Supply voltage: AC 230 V, 50/60 Hz Starting current: max. 300 mA for max. 200 ms Operating current: 8 mA Power consumption: 1.8 W Lift: approx. 4 mm Running time: 45 s/mm Positioning force: 100 N Circulating medium temperature: 0-100°C Type of protection: IP 54 / II, in all installations Connecting cable: 1 m, 2x0.75 mm?? PVC Dimensions: 60x44x61 mm (HxWxD) To be completed with: Room temperature control insert with switch, art. no. 536302. Valve adapter VA10, art. no. 639110. Valve adapter VA50, art. no 639150. Valve adapter VA78, art. no. 639178. Valve adapter VA80, art. no. 639180. In KNX, to be completed with Heating actuator REG-K/6x230/ 0.05 A, art. no. 645129.
9272
639125 THERMOELECTRIC VALVE DRIVE 230 V CLIMATE CONTROL
9273 639126 Thermoelectric valve drive 24 V CLIMATE CONTROL
Thermoelectric valve drive for opening and closing valves. For 2-step or PWM control of heating, air conditioning and ventilation systems, individual room control of surface heaters, control of heating circuit distributors, radiators, convector heaters, cooling ceilings. Fan coil actuator REG-K or a room temperature control unit (24 V) with 2- step or PWM output activates. Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors. Functions: • First-open function: The drive is factory-set to de-energised open. This allows the heating to be operated during the building shell phase. • De-energised closed • Functional display (open, closed, intermediate settings) • Adjustment control • Protection against dismantling • Plug-in connecting cable • Plug-in assembly Supply voltage: AC/DC 24 V +20%/-10%, 0- 60 Hz Starting current: max. 250 mA for max. 2 min Operating current: 75 mA Power consumption: 1.8 W Lift: approx. 4 mm Running time: 45 s/mm Positioning force: 100 N Medium temperature: 0-100°C Type of protection/protection class: IP 54 / II, in all installation positions Connecting cable: 1 m, 2x0.75 mm?? PVC Dimensions: 60 x 44 x 61 mm (HxWxD) To be completed with: Room temperature control insert with switch, art. no. 536304. Power supply REG, AC 24 V / 1 A, art. no. 663529. Valve adapter VA10, art. no. 639110. Valve adapter VA50, art. no 639150. Valve adapter VA78, art. no. 639178. Valve adapter VA80, art. no. 639180. In KNX, to be completed with: Fan coil actuator REG-K, art. no. 645094. Power supply REG, AC 24 V / 1 A, art. no. 663529. Note: Protective cap AA SK 1000 (aluminium, white RAL 9016) available on request. To install the protective cap, a higher valve adapter must be used (available on request). Check compact radiators in advance to see if they are suitable.
9273
639126 THERMOELECTRIC VALVE DRIVE 24 V CLIMATE CONTROL
9485 518460 Frame System M Aluminium SIN FAMILIA
9485
518460 FRAME SYSTEM M ALUMINIUM SIN FAMILIA
9595 518419 SYSTEM M ADAPTER PUSH BUTTONS
Inserts for System M can be integrated into System Design with the adapter.
9595
518419 SYSTEM M ADAPTER PUSH BUTTONS
10056 MEG2301-4146 MERT SCHUKO-Steckdose 16A MEG2301-4146 Edelstahl AC 250V SIN FAMILIA
- ARTEC-SCHUKO®-Steckdosen haben überwiegend Steckklemmen - Alle Ausführungen mit Schraubklemmen sind entsprechend beschrieben - Beide Klemmenarten sind als Verbindungsklemmen nach VDE 0620 genehmigt D = Duroplast T = Thermoplast M = Metall 16 A, AC 250 V
10056
MEG2301-4146 MERT SCHUKO-STECKDOSE 16A MEG2301-4146 EDELSTAHL AC 250V SIN FAMILIA
10933 MEG6212-4044 Button panel for bus system PUSH BUTTONS
Button panel for bus system Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of actuation points 6, With display, Status-LED, Manual set point setting, Temperature controller, Timer clock, With anti-theft/dismantling protection, Central functional unit for senders/actuators, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour Cream white/electro white, RAL-number (akin) 1013, Degree of protection (IP) IP20, Bus connection included, Colour variant White,
10933
MEG6212-4044 BUTTON PANEL FOR BUS SYSTEM PUSH BUTTONS
12760 489119 Frame white crystal, 1 channel PUSH BUTTONS
Frame white crystal, 1 channel
12760
489119 FRAME WHITE CRYSTAL, 1 CHANNEL PUSH BUTTONS
12921 483144 Frame Antik, 1-gang PUSH BUTTONS
Frame Antik, 1-gang
12921
483144 FRAME ANTIK, 1-GANG PUSH BUTTONS
13566 MEG3429-0344 Doppelwippe mit Kontroll-fenster und Kennzeichnung für Hotelanwendungen PUSH BUTTONS

 

13566
MEG3429-0344 DOPPELWIPPE MIT KONTROLL-FENSTER UND KENNZEICHNUNG FÜR HOTELANWENDUNGEN PUSH BUTTONS
13573 587644 Bell push-button with LED displays SIN FAMILIA
Electronic bell push-button with two LED displays,
bell crossed through/chambermaid.
For use in hotels as a doorbell button on room
doors. Triggering options for the two LED displays
(Do not disturb - red LED; Make up room - green
LED) via the corresponding switch insert and
rocker for two-circuit switch with imprint. Any
number of alternating current bells with a current
consumption of 10-500 mA can be connected. The
power supply comes from a commercially available
safety transformer.
With short-circuit and overvoltage protection.
With screw terminals.
Input voltage:
min. AC 6 V, max. AC 24 V (SELV)
Switching current:
min. 10 mA, max. 500 mA
Connecting terminals:
Screw terminals for 0.8-
1.5 mm
13573
587644 BELL PUSH-BUTTON WITH LED DISPLAYS SIN FAMILIA
13577 MEG3612-0000 2-pole switch flush mounted ,16 AX, AC 250 V SIN FAMILIA
2-pole switch flush mounted Wiring system 2-pole switch, Method of operation Rocker/button, Assembly arrangement Basic element, Number of rockers 1, Mounting method Flush mounted (plaster), Type of fastening Mounting with claw and screw, Material Other, Material quality Other, Halogen free, Illumination Without illumination, Suitable for degree of protection (IP) IP20, Nominal voltage 250V, Rated current 16A, Switching current for fluorescent lamps 16AX, Connection type Plug clamp,
13577
MEG3612-0000 2-POLE SWITCH FLUSH MOUNTED ,16 AX, AC 250 V SIN FAMILIA
13578 MEG3112-0000 2-pole switch flush mounted ,10 AX, AC 250 V SIN FAMILIA
2-pole switch flush mounted Wiring system 2-pole switch, Method of operation Rocker/button, Assembly arrangement Basic element, Number of rockers 1, Mounting method Flush mounted (plaster), Type of fastening Mounting with claw and screw, Material Other, Material quality Other, Halogen free, Illumination Without illumination, Suitable for degree of protection (IP) IP20, Nominal voltage 250V, Rated current 10A, Switching current for fluorescent lamps 10X, Connection type Plug clamp,
13578
MEG3112-0000 2-POLE SWITCH FLUSH MOUNTED ,10 AX, AC 250 V SIN FAMILIA
13579 MEG3150-0000 Push button 1 make contact SIN FAMILIA
Push button 1 make contact (NO) Assembly arrangement Basic element, Model Single push button, Method of operation Rocker, Contacts 1 make contact (NO), Number of rockers 1, Mounting method Flush mounted (plaster), Type of fastening Mounting with claw and screw, Material Other, Material quality Other, Halogen free, Imprint None, Suitable for degree of protection (IP) IP20, Nominal voltage 250V, Rated current 10A, Width of device 73mm, Height of device 73mm, Depth of device 37mm,
13579
MEG3150-0000 PUSH BUTTON 1 MAKE CONTACT SIN FAMILIA
13643 488819 Frame 2-gang white SIN FAMILIA
Frame 1-gang white Number of units 1, Mounting direction Horizontal and vertical, Suitable for flush-mounted installation, Suitable for floor box, Suitable for wall duct, Material Plastic, Material quality Thermoplastic, Halogen free, Surface treatment Untreated, Type of surface Matt, Colour White, RAL-number (akin) 9010, Degree of protection (IP) IP20, Type of fastening Clamping/screw mounting, Width 85,8mm, Height 154,6mm, Depth 10,1mm, Built-in width 0mm, Built-in height 0mm,
13643
488819 FRAME 2-GANG WHITE SIN FAMILIA
13760 MEG2151-0444 Socket outlet american national standard SIN FAMILIA
Socket outlet american national standard Model American National Standard, Number of units 1, Number of socket outlets switchable 0, Cover Central cover plate, Imprint/indication Without imprint, Connection type Screwed terminal, Colour Cream white/electro white, RAL-number (akin) 1013, Special power supply No special power supply, Mounting method Flush mounted (plaster), Type of fastening Mounting with claw and screw, Material Plastic, Material quality Thermoplastic, Halogen free, Surface treatment Untreated, Type of surface Matt, Nominal current 15A, Nominal voltage 125V, Phase pickup None, Suitable for degree of protection (IP) IP20, Width of device 73mm, Height of device 73mm, Depth of device 28mm,
13760
MEG2151-0444 SOCKET OUTLET AMERICAN NATIONAL STANDARD SIN FAMILIA
13766 201219 Socket British standard, 13 A, 250 V AC, polar white SIN FAMILIA
 Socket British standard, 13 A, 250 V AC, polar white
13766
201219 SOCKET BRITISH STANDARD, 13 A, 250 V AC, POLAR WHITE SIN FAMILIA
16928 MEG4020-3619 M-Pure-Rahmen, 2 fach, polarweiß, PUSH BUTTONS
M-Pure-Rahmen, 2 fach, polarweiß,
16928
MEG4020-3619 M-PURE-RAHMEN, 2 FACH, POLARWEIß, PUSH BUTTONS
17311 400244 Frame 2 fold, AQUADESIGN PUSH BUTTONS
AQUADESIGN-Rahmen, 2fach
17311
400244 FRAME 2 FOLD, AQUADESIGN PUSH BUTTONS
17316 400144 AQUADESIGN- frame, 1-fold PUSH BUTTONS
AQUADESIGN- frame, 1fach
17316
400144 AQUADESIGN- FRAME, 1-FOLD PUSH BUTTONS
17322 489260 M-PLAN frame 2 fold PUSH BUTTONS
M-PLAN frame 2 fold
17322
489260 M-PLAN FRAME 2 FOLD PUSH BUTTONS
17332 486460 M-PLAN- frame 4 fold PUSH BUTTONS
M-PLAN- frame 4 fold
17332
486460 M-PLAN- FRAME 4 FOLD PUSH BUTTONS
17334 298360 Central plate for UAE, 1 fach PUSH BUTTONS

Central plate for UAE, 1 fach

17334
298360 CENTRAL PLATE FOR UAE, 1 FACH PUSH BUTTONS
17340 MEG3116-0000 Off / changeover switch insert, 1-pole, 10 AX, AC 250 V, plug-in terminals OTHER ACCESSORIES
Off / changeover switch insert, 1-pole, 10 AX, AC 250 V, plug-in terminals

description
Additional packaging available:
10 AX, AC 250 V. Features: -Front sided retrofitting of QuickFlex lighting modules without switch dismantling. -Frontside measurement and test contacts, accessible without switch dismantling. -Screw screw for claw fixing. - Lowered claws with reset spring. -Highlight galvanized tragring insulated to the claw. With claws and screw fastening. With plug-in clamps. To be completed with: ==> Rocker for switch / pushbutton system M
17340
MEG3116-0000 OFF / CHANGEOVER SWITCH INSERT, 1-POLE, 10 AX, AC 250 V, PLUG-IN TERMINALS OTHER ACCESSORIES
17343 516944 INTERMEDIATE RING WITH HINGED LID OTHER ACCESSORIES
INTERMEDIATE RING WITH HINGED LID
17343
516944 INTERMEDIATE RING WITH HINGED LID OTHER ACCESSORIES
17349 389144 1-M- Frame, 1 fold PUSH BUTTONS
1-M- Frame, 1 fold
17349
389144 1-M- FRAME, 1 FOLD PUSH BUTTONS
17351 389244 1-M-Frame, 2 folds PUSH BUTTONS
1-M-Frame, 2 folds
17351
389244 1-M-FRAME, 2 FOLDS PUSH BUTTONS
17353 389344 1-M-frame, 3 fold PUSH BUTTONS

1-M-frame, 3 fold

17353
389344 1-M-FRAME, 3 FOLD PUSH BUTTONS
17356 389444 1-M-frame 4 fold PUSH BUTTONS
1-M-Rahmen, 4fach
17356
389444 1-M-FRAME 4 FOLD PUSH BUTTONS
17359 389544 1-M-frame, 5 fold SIN FAMILIA
1-M-Rahmen, 5fach
17359
389544 1-M-FRAME, 5 FOLD SIN FAMILIA
17362 MEG3115-0000 Series switch flush mounted 1-polig, 10 AX, AC 250 V OTHER ACCESSORIES
Series switch flush mounted Wiring system Series switch, Method of operation Rocker/button, Assembly arrangement Basic element, Number of modules (module system) 0, Number of rockers 2, Mounting method Flush mounted (plaster), Type of fastening Mounting with claw and screw, With mounting plate, Material Other, Material quality Other, Halogen free, Label space/information surface No, Illumination No, Function lighting Not applicable, Type of lighting Not included, Suitable for degree of protection (IP) IP20, Nominal voltage 250V, Rated current 10A, Switching current for fluorescent lamps 10AX, Connection type Plug clamp, Width of device 73mm, Height of device 73mm, Depth of device 37mm, Built-in depth 28mm,
17362
MEG3115-0000 SERIES SWITCH FLUSH MOUNTED 1-POLIG, 10 AX, AC 250 V OTHER ACCESSORIES
17363 MEG3126-0000 Alternating switc, 1-polig 10 AX, AC 250 V OTHER ACCESSORIES
Alternating-/alternating switch Wiring system Alternating-/alternating switch (2x 3-way), Method of operation Rocker/button, Assembly arrangement Basic element, Number of modules (module system) 0, Number of rockers 2, Mounting method Flush mounted (plaster), Type of fastening Mounting with claw and screw, With mounting plate, Material Other, Material quality Other, Halogen free, Label space/information surface No, Illumination No, Function lighting Not applicable, Type of lighting Not included, Suitable for degree of protection (IP) IP20, Nominal voltage 250V, Rated current 10A, Switching current for fluorescent lamps 10AX, Connection type Plug clamp, Width of device 73mm, Height of device 73mm, Depth of device 37mm, Built-in depth 28mm,
17363
MEG3126-0000 ALTERNATING SWITC, 1-POLIG 10 AX, AC 250 V OTHER ACCESSORIES
17365 297560 Central cover plate SIN FAMILIA
Central cover plate Assembly arrangement Central cover plate, Utilization Coaxial antenna socket outlet, Imprintable label Without indication field, Mounting method Flush mounted (plaster), Material Plastic, Material quality Thermoplastic, Halogen free, Surface treatment Untreated, Type of surface Matt, Colour White, RAL-number (akin) 9010, Type of fastening Mounting with screw, Width of device 57mm, Height of device 56mm, Depth of device 10mm,
17365
297560 CENTRAL COVER PLATE SIN FAMILIA
17370 315460 Card switch, thermoplastic brilliant OTHER ACCESSORIES
Card switch, thermoplastic brilliant
17370
315460 CARD SWITCH, THERMOPLASTIC BRILLIANT OTHER ACCESSORIES
17373 391814 Basic element with central cover plate OTHER ACCESSORIES

Abdeckung für Relais, Rollladenmehrfachsteuerrelais, Summer, Leistungszusätze, KNX-Unterputzgeräte usw.. Durch mechanische Bearbeitung (Bohren, Fräsen, etc.) universell verwendbar. Ohne Krallen, für Schraubbefestigung. Material: Thermoplast edelmatt. Farbe: anthrazit.

17373
391814 BASIC ELEMENT WITH CENTRAL COVER PLATE OTHER ACCESSORIES
17376 486360 M-PLAN-frame, 3fold, Thermoplast brillant, PUSH BUTTONS
M-PLAN-frame, 3fold, Thermoplast brillant,
17376
486360 M-PLAN-FRAME, 3FOLD, THERMOPLAST BRILLANT, PUSH BUTTONS
17380 MEG3156-0000 Push button 1 change-over contact OTHER ACCESSORIES
Push button 1 change-over contact
17380
MEG3156-0000 PUSH BUTTON 1 CHANGE-OVER CONTACT OTHER ACCESSORIES
17381 MEG5111-0300 Intelligent control element, 1 fold OTHER ACCESSORIES
Intelligent control element, 1 fold
17381
MEG5111-0300 INTELLIGENT CONTROL ELEMENT, 1 FOLD OTHER ACCESSORIES
17382 MEG5180-0000 Control unit for light control system, 1-10V OTHER ACCESSORIES
Control unit for light control system Mounting method Flush mounted (plaster), Control current 50mA, Rated current 10A, Nominal voltage 230V, Frequency 60 ... 60Hz, Type of dimming 1-10 V, Method of operation Other, Substation input, Applicable with button, Applicable with movement sensor, Applicable with presence indicator, Applicable with time switch/timer, Applicable with transmission button, Applicable with infrared button, Width of device 73mm, Height of device 73mm, Depth of device 32mm,
17382
MEG5180-0000 CONTROL UNIT FOR LIGHT CONTROL SYSTEM, 1-10V OTHER ACCESSORIES
17386 MEG5250-0460 Cover plate for dimmer PUSH BUTTONS

Cover plate for dimmer

17386
MEG5250-0460 COVER PLATE FOR DIMMER PUSH BUTTONS
17388 MEG5142-0000 Control unit for light control system 1-10V OTHER ACCESSORIES
Control unit for light control system
17388
MEG5142-0000 CONTROL UNIT FOR LIGHT CONTROL SYSTEM 1-10V OTHER ACCESSORIES
17800 515125 Simple Square Frame 86x83mm PUSH BUTTONS

Material: Glossy, antibacterial thermoplastic. Smooth surface and even disinfectant with antibacterial properties.

Color: similar to RAL 9016 color: bright white active.

Outter Dimensions: 86x83mm
 
Inner Dimensions: 55x55mm
17800
515125 SIMPLE SQUARE FRAME 86X83MM PUSH BUTTONS
18053 MEG2300-0414 SCHUKO socket outlet, increased contact protection, plug-in terminals, System M OTHER ACCESSORIES
16 A, AC 250 V. Integrated high contact protection according to VDE 0620 part 1 (child protection). Features: -Flex-sided retrofitting of QuickFlex add-on modules without disassembling the socket. -Screw screw for claw fixing. - Lowered claws with reset spring. -Highlight galvanized tragring insulated to the claw. With claws and screw fastening. With plug-in terminals. Accessories: ==> Extension set overvoltage protection
18053
MEG2300-0414 SCHUKO SOCKET OUTLET, INCREASED CONTACT PROTECTION, PLUG-IN TERMINALS, SYSTEM M OTHER ACCESSORIES
18054 MEG3117-0000 Cross-switch insert, 1-pole, 10 AX, AC 250 V, plug-in terminals OTHER ACCESSORIES
 10 AX, AC 250 V. Features: -Front sided retrofitting of QuickFlex lighting modules without switch dismantling. -Frontside measurement and test contacts, accessible without switch dismantling. -Screw screw for claw fixing. - Lowered claws with reset spring. -Highlight galvanized tragring insulated to the claw. With claws and screw fastening. With plug-in terminals.
18054
MEG3117-0000 CROSS-SWITCH INSERT, 1-POLE, 10 AX, AC 250 V, PLUG-IN TERMINALS OTHER ACCESSORIES
18055 433514 System M double key set OTHER ACCESSORIES
  Rocker for series switch, anthracite, System M
For serial, double-throw switch and double-button operation. To be completed with: ==> Switch and pushbutton, 2-gang. Material: Thermoplast edelmatt. Color anthracite.
18055
433514 SYSTEM M DOUBLE KEY SET OTHER ACCESSORIES
18056 465706 Double RJ45 input cat 6 OTHER ACCESSORIES

For connecting analog or digital terminals via two 8-pin UAE jacks. Connection via LSA terminals. To be completed with: ==> Central plate for UAE use, double system M 2961 .., 2980 .., system area 2926 .., OCTOCOLOR 2920 .. Color: white.

18056
465706 DOUBLE RJ45 INPUT CAT 6 OTHER ACCESSORIES
18057 MEG5250-0414 Central panel with rotary knob, System M OTHER ACCESSORIES
 
Central plate with rotary knob, thermoplast brilliant,
anthracite
18057
MEG5250-0414 CENTRAL PANEL WITH ROTARY KNOB, SYSTEM M OTHER ACCESSORIES
18058 577099 Universal super dimmer insert, 25-420 VA OTHER ACCESSORIES
 For ohmic, inductive and capacitive loads, eg incandescent lamps, dimmable wound transformers or electronic transformers. (Phase gating or phase portion). The universal dimmer automatically detects the connected load. Do not connect any mixing loads. With memory function, can be switched off. Rated voltage: AC 230 V, 50 Hz. Minimum load: 25 VA. Maximum load: 420 VA. Neutral conductor: not required (2 conductor system)
18058
577099 UNIVERSAL SUPER DIMMER INSERT, 25-420 VA OTHER ACCESSORIES
18125 MEG3155-0000 Double button normally open. 10Amp SIN FAMILIA
  Characteristics:
Front-side retrofitting of QuickFlex lighting modules without switch dismantling.
Front-side measuring and test contacts; Accessible without switch dismantling.
Quick-threading screws for claws.
Recessed claws with reset spring.
High-gloss galvanized tragring insulated to the claw.
With claws and screw fastening.
With plug-in clamps
18125
MEG3155-0000 DOUBLE BUTTON NORMALLY OPEN. 10AMP SIN FAMILIA
18126 432525 Double key play SIN FAMILIA
For serial, double-throw switch and double-button operation.
To be completed with: ==> Switch and pushbutton, 2-gang.
Material: Thermoplast brilliant, antibacterial. Smooth and self-disinfecting surface with antibacterial effect.
Color: active white glossy, similar to RAL 9016.
18126
432525 DOUBLE KEY PLAY SIN FAMILIA
18127 MTN402325 Triple Frame Elegance Series SIN FAMILIA
 
18127
MTN402325 TRIPLE FRAME ELEGANCE SERIES SIN FAMILIA
18174 MEG4010-3619 M-Pure-Frame, single PUSH BUTTONS
The M-Pure and M-Pure Decor frames can be combined with more than 280 System M inserts and are available in 1- to 5-way and 2-way without middle crosspieces. KNX and building communication solutions can be implemented on request.
Without the need to change the inserts, frames and rockers are easily interchangeable. System M adapts to all functional and design requirements.

Thermoplast brilliant - active white
For vertical and horizontal mounting.
18174
MEG4010-3619 M-PURE-FRAME, SINGLE PUSH BUTTONS
18432 488860 M-PLAN frame, 2-gang without middle bridge. plastic aluminium color OTHER ACCESSORIES
M-PLAN frame, 2-gang without middle bridge. plastic aluminium color
18432
488860 M-PLAN FRAME, 2-GANG WITHOUT MIDDLE BRIDGE. PLASTIC ALUMINIUM COLOR OTHER ACCESSORIES


KNX SPECIAL CATALOGUES
Different looks for KNX push buttons
Push buttons
Smart metering
Iddero Verso Interactive Presentation

LEARN
Free webinars
uBrick Tutorials
VideoTutorials CBSE


PARTICIPATE
µBrick Trivia
KNX Tips & tricks
TEST
Free test of CBSE visualization

LATEST KNX NEWS
All news

LATEST KNX OFFERS
All offers
DOWNLOADS
KNX - All brands

FUTURASMUS KNX GROUP
Contact
Location
Futurasmus in the world
FOLLOW US
YouTube Channel
Facebook
LinkedIN
Google+
Twitter

KNX++ TRAINING CENTER
Futurasmus Zentrum

CERTIFIED KNX TEST LAB
Futurasmus KNX Lab
SPECIALIZED KNX WHOLESALER CERTIFIED KNX TRAINING CENTRE
Futurasmus KNX Group is a highly specialized and internationally active KNX Wholesaler, being our forte the excellent technical support we provide. You can visit our online catalogue in this website and, if you are a professional, ask for a non binding offer for your KNX projects. Should you be interested in buying KNX components, you are welcome to read our General Sales Conditions and contact our technicians and commercial agents per telephone, e-mail or online help. Since 2003 we have been a Certified Training Centre KNX++, which means that we are entitled to impart the KNX Basic Course as well as the KNX Advanced Course and KNX Tutor Course. We are manufacturer-independent and also offer other specialized and monographic KNX seminars. After teaching more than 1.500 KNX partners, our KNX Trainers have quite a large and positive expertise. Please, contact us for customized KNX training worldwide (groups of at least 8 people) at training@futurasmus-knxgroup.org
USE OF COOKIES
We use our own and third-party cookies, analyzing your browsing habits in out website, with the finality of ensuring the quality, security and improvement of the offered services through the same. In the case that the user does not explicitly state whether to accept the installation of cookies, but continues using our website, it will mean that he has consented expressly, informing him about the possibility to block or remove the installed cookies on his computer by configuring the appropriate settings of the browser. You can get more information on this subject reading our "Cookies Policy".